Hardware List

Results for igt@kms_flip@wf_vblank-ts-check@a-edp1

Machine description: shard-lnl-6

Result: Pass

i915_display_info24 igt_runner24 results24.json results24-xe-load.json i915_display_info_post_exec24 boot24 dmesg24

Detail	Value
Duration	11.66 seconds
Hostname	shard-lnl-6
Igt-Version	IGT-Version: 1.30-g05663ba9a (x86_64) (Linux: 6.14.0-rc4-xe+ x86_64)
Out	Using IGT_SRANDOM=1740802782 for randomisation Opened device: /dev/dri/card0 Using monotonic timestamps Starting subtest: wf_vblank-ts-check Starting dynamic subtest: A-eDP1 2880x1800: 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa Expected frametime: 16664us; measured 16666.1us +- 4.177us accuracy 0.08% Dynamic subtest A-eDP1: SUCCESS (11.664s)
Err	Starting subtest: wf_vblank-ts-check Starting dynamic subtest: A-eDP1 Dynamic subtest A-eDP1: SUCCESS (11.664s)
Dmesg	<6> [155.962297] Console: switching to colour dummy device 80x25 <6> [155.962435] [IGT] kms_flip: executing <7> [155.969110] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:198:DP-1] <7> [155.969133] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:198:DP-1] <7> [155.969305] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) <7> [155.969410] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:198:DP-1] disconnected <7> [155.969765] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:210:DP-2] <7> [155.969776] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:210:DP-2] <7> [155.969897] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) <7> [155.969986] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:210:DP-2] disconnected <7> [155.970342] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:218:DP-3] <7> [155.970353] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:218:DP-3] <7> [155.970470] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (disconnected -> tbt-alt) <7> [155.970557] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:218:DP-3] disconnected <7> [155.970971] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:189:eDP-1] <7> [155.970981] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:189:eDP-1] <7> [155.971729] xe 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [xe]] DSC DPCD: 00 11 00 76 0b 01 01 80 00 01 06 66 08 00 00 00 <7> [155.972277] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000 <7> [155.972392] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [155.972501] xe 0000:00:02.0: [drm:intel_dp_print_rates [xe]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [155.972638] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:189:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 120 Hz <5> [155.972646] [drm] DisplayID checksum invalid, remainder is 248 <5> [155.972648] [drm] DisplayID checksum invalid, remainder is 248 <7> [155.972649] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:189:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <5> [155.972652] [drm] DisplayID checksum invalid, remainder is 248 <7> [155.972653] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:189:eDP-1] ELD monitor <5> [155.972656] [drm] DisplayID checksum invalid, remainder is 248 <7> [155.972658] xe 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:189:eDP-1] ELD size 20, SAD count 0 <5> [155.972661] [drm] DisplayID checksum invalid, remainder is 248 <7> [155.972677] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:189:eDP-1] VRR capable: yes <7> [155.972801] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:189:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [155.973523] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [155.973606] xe 0000:00:02.0: [drm:intel_dp_set_edid [xe]] [CONNECTOR:189:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <5> [155.974569] [drm] DisplayID checksum invalid, remainder is 248 <5> [155.974571] [drm] DisplayID checksum invalid, remainder is 248 <5> [155.974573] [drm] DisplayID checksum invalid, remainder is 248 <7> [155.974608] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:189:eDP-1] probed modes: <7> [155.974625] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [155.974667] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:198:DP-1] <7> [155.974679] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:198:DP-1] <7> [155.974827] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:198:DP-1] disconnected <7> [155.974849] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:210:DP-2] <7> [155.974859] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:210:DP-2] <7> [155.974990] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:210:DP-2] disconnected <7> [155.975009] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:218:DP-3] <7> [155.975019] xe 0000:00:02.0: [drm:intel_dp_detect [xe]] [CONNECTOR:218:DP-3] <7> [155.975150] xe 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:218:DP-3] disconnected <6> [155.975648] [IGT] kms_flip: starting subtest wf_vblank-ts-check <6> [155.976844] [IGT] kms_flip: starting dynamic subtest A-eDP1 <7> [155.977440] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:226] <7> [155.977666] xe 0000:00:02.0: [drm:drm_mode_addfb2] [FB:228] <7> [156.067093] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe A] <7> [156.067416] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.enable (expected yes, found no) <7> [156.067768] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.active (expected yes, found no) <7> [156.068033] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1) <7> [156.068322] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in lane_count (expected 4, found 0) <7> [156.068571] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 6329869/8388608 link 421991/524288, found tu 0, data 0/0 link 0/0) <7> [156.068843] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000) <7> [156.069076] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0) <7> [156.069435] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 2880, found 0) <7> [156.069694] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3040, found 0) <7> [156.069913] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 2880, found 0) <7> [156.070131] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3040, found 0) <7> [156.070393] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2928, found 0) <7> [156.070657] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2960, found 0) <7> [156.070863] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0) <7> [156.071104] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0) <7> [156.071350] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0) <7> [156.071554] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1809, found 0) <7> [156.071734] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1906, found 0) <7> [156.071913] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1906, found 0) <7> [156.072113] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 2880, found 0) <7> [156.072317] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3040, found 0) <7> [156.072486] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 2880, found 0) <7> [156.072649] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3040, found 0) <7> [156.072814] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2928, found 0) <7> [156.072993] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2960, found 0) <7> [156.073154] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0) <7> [156.073311] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0) <7> [156.073467] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0) <7> [156.073616] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1809, found 0) <7> [156.073762] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1906, found 0) <7> [156.073906] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1906, found 0) <7> [156.074052] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0) <7> [156.074221] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0) <7> [156.074359] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0) <7> [156.074498] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0) <7> [156.074633] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 347710, found 0) <7> [156.074762] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 347710, found 0) <7> [156.074906] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in port_clock (expected 432000, found 0) <7> [156.075037] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:82:pipe A] fastset requirement not met, forcing full modeset <7> [156.075234] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no <7> [156.075359] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:82:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0 <7> [156.075545] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] ddb ( 0 - 4054) -> ( 0 - 0), size 4054 -> 0 <7> [156.075680] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:77:cursor A] ddb (4054 - 4096) -> ( 0 - 0), size 42 -> 0 <7> [156.075797] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [156.075905] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] lines 2, 12, 12, 12, 11, 12, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [156.076010] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] blocks 49, 289, 289, 289, 265, 289, 0, 0, 63, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [156.076110] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] min_ddb 55, 319, 319, 319, 293, 319, 0, 0, 64, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [156.076229] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:82:pipe A] data rate 0 num active planes 0 <7> [156.076365] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400 <7> [156.076494] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400 <7> [156.076620] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [156.076741] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [156.076859] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0 <7> [156.076981] xe 0000:00:02.0: [drm:intel_modeset_calc_cdclk [xe]] Can change cdclk via squashing <7> [156.077095] xe 0000:00:02.0: [drm:intel_modeset_calc_cdclk [xe]] New cdclk calculated to be logical 153600 kHz, actual 153600 kHz <7> [156.077221] xe 0000:00:02.0: [drm:intel_modeset_calc_cdclk [xe]] New voltage level calculated to be logical 0, actual 0 <7> [156.077382] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:82:pipe A] enable: no [modeset] <7> [156.077515] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:32:plane 1A] fb: [NOFB], visible: no <7> [156.077627] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:41:plane 2A] fb: [NOFB], visible: no <7> [156.077735] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:50:plane 3A] fb: [NOFB], visible: no <7> [156.077842] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:59:plane 4A] fb: [NOFB], visible: no <7> [156.077948] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:68:plane 5A] fb: [NOFB], visible: no <7> [156.078049] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:77:cursor A] fb: [NOFB], visible: no <7> [156.078230] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [156.078359] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [156.078523] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2 <7> [156.095597] xe 0000:00:02.0: [drm:intel_edp_backlight_off [xe]] <7> [156.297462] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:189:eDP-1] set backlight PWM = 0 <7> [156.297865] xe 0000:00:02.0: [drm:intel_disable_transcoder [xe]] disabling pipe A <7> [156.319338] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 turn panel power off <7> [156.319728] xe 0000:00:02.0: [drm:intel_pps_off_unlocked [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 wait for panel power off time <7> [156.319872] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000 <7> [156.320041] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060 <7> [156.320200] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:188:DDI A/PHY A] - short <7> [156.372316] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000 <7> [156.372621] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:188:DDI A/PHY A] - short <7> [156.394456] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete <7> [156.394846] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:188:DDI A/PHY A] <7> [156.394900] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling AUX_A <7> [156.395390] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring short hpd on eDP [ENCODER:188:DDI A/PHY A] <7> [156.395366] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:32:plane 1A] <7> [156.395958] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:188:DDI A/PHY A] <7> [156.396261] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:197:DDI TC1/PHY TC1] <7> [156.396514] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:199:DP-MST A] <7> [156.396757] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:200:DP-MST B] <7> [156.397038] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:201:DP-MST C] <7> [156.397298] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:209:DDI TC2/PHY TC2] <7> [156.397526] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:211:DP-MST A] <7> [156.397748] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:212:DP-MST B] <7> [156.397964] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:213:DP-MST C] <7> [156.398257] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:217:DDI TC3/PHY TC3] <7> [156.398474] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:219:DP-MST A] <7> [156.398727] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:220:DP-MST B] <7> [156.398939] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:221:DP-MST C] <7> [156.399164] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:189:eDP-1] <7> [156.399423] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no) <7> [156.399651] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: yes -> no (pipe: ) <7> [156.399874] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Post changing CDCLK to 153600 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [156.400192] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no) <7> [156.400501] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=384 <7> [156.400786] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0x1 <7> [156.401250] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling PW_A <7> [156.401685] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:82:pipe A] <7> [156.402034] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:134:pipe B] <7> [156.402439] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:186:pipe C] <7> [156.402701] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe A] <7> [156.402771] xe 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:189:eDP-1] <7> [156.402934] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CONNECTOR:189:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [156.403304] xe 0000:00:02.0: [drm:intel_dp_compute_config_limits [xe]] [ENCODER:188:DDI A/PHY A][CRTC:82:pipe A] DP link limits: pixel clock 347710 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 max link_bpp 30.0000 <7> [156.403591] xe 0000:00:02.0: [drm:intel_dp_compute_link_config [xe]] DP lane count 4 clock 432000 bpp input 30 compressed 0.0000 link rate required 1303913 available 1728000 <7> [156.403881] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:82:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [156.404182] xe 0000:00:02.0: [drm:intel_ddi_compute_config_late [xe]] [ENCODER:188:DDI A/PHY A] [CRTC:82:pipe A] <7> [156.404524] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.enable (expected no, found yes) <7> [156.404830] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.active (expected no, found yes) <7> [156.405126] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0) <7> [156.405407] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in lane_count (expected 0, found 4) <7> [156.405684] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 6329869/8388608 link 421991/524288) <7> [156.405959] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100) <7> [156.406267] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1) <7> [156.406529] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 2880) <7> [156.406778] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3040) <7> [156.407080] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 2880) <7> [156.407347] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3040) <7> [156.407603] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2928) <7> [156.407832] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2960) <7> [156.408044] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800) <7> [156.408279] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800) <7> [156.408479] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803) <7> [156.408675] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1809) <7> [156.408866] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1906) <7> [156.409049] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1906) <7> [156.409248] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 2880) <7> [156.409243] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7> [156.409425] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3040) <7> [156.409461] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:188:DDI A/PHY A] - long <7> [156.409595] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 2880) <7> [156.409651] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 10 <7> [156.409789] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3040) <7> [156.409858] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:188:DDI A/PHY A] <7> [156.409958] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2928) <7> [156.410121] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2960) <7> [156.410276] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800) <7> [156.410428] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800) <7> [156.410574] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803) <7> [156.410716] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1809) <7> [156.410858] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1906) <7> [156.410997] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1906) <7> [156.411137] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1) <7> [156.411294] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2) <7> [156.411441] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8) <7> [156.411570] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30) <7> [156.411692] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 347710) <7> [156.411813] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 347710) <7> [156.411932] xe 0000:00:02.0: [drm:intel_pipe_config_compare [xe]] [CRTC:82:pipe A] fastset requirement not met in port_clock (expected 0, found 432000) <7> [156.412048] xe 0000:00:02.0: [drm:intel_atomic_check [xe]] [CRTC:82:pipe A] fastset requirement not met, forcing full modeset <7> [156.412441] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes <7> [156.412550] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [CRTC:82:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1 <7> [156.412689] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] ddb ( 0 - 0) -> ( 0 - 4054), size 0 -> 4054 <7> [156.412787] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:77:cursor A] ddb ( 0 - 0) -> (4054 - 4096), size 0 -> 42 <7> [156.412880] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,stwm <7> [156.412973] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 2, 12, 12, 12, 11, 12, 0, 0, 0, 3, 0 <7> [156.413060] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 49, 289, 289, 289, 265, 289, 0, 0, 63, 73, 87 <7> [156.413159] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 55, 319, 319, 319, 293, 319, 0, 0, 64, 82, 88 <7> [156.413244] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:82:pipe A] data rate 1390840 num active planes 1 <7> [156.413362] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 1461 qgv_peak_bw: 38400 <7> [156.413471] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 1461 qgv_peak_bw: 38400 <7> [156.413577] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [156.413679] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 1461 qgv_peak_bw: 38400 <7> [156.413779] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 1461 <7> [156.413878] xe 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [xe]] [PLANE:32:plane 1A] min cdclk (173855 kHz) > [CRTC:82:pipe A] min cdclk (0 kHz) <7> [156.413980] xe 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [xe]] new bandwidth min cdclk (27165 kHz) > old min cdclk (0 kHz) <7> [156.414079] xe 0000:00:02.0: [drm:intel_modeset_calc_cdclk [xe]] Can change cdclk via squashing <7> [156.414185] xe 0000:00:02.0: [drm:intel_modeset_calc_cdclk [xe]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz <7> [156.414280] xe 0000:00:02.0: [drm:intel_modeset_calc_cdclk [xe]] New voltage level calculated to be logical 0, actual 0 <7> [156.414387] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [CRTC:82:pipe A] enable: yes [modeset] <7> [156.414494] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [156.414600] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7> [156.414703] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] MST master transcoder: <invalid> <7> [156.414797] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [156.414888] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] joiner: no, pipes: 0x0 <7> [156.414978] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] splitter: disabled, link count 0, overlap 0 <7> [156.415064] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m_n: lanes: 4; data_m: 6329869, data_n: 8388608, link_m: 421991, link_n: 524288, tu: 64 <7> [156.415158] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [156.415245] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] fec: disabled, enhanced framing: disabled <7> [156.415336] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] sdp split: disabled <7> [156.415425] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled <7> [156.415512] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] minimum HBlank: 0 <7> [156.415595] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [156.415668] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] DP SDP: VSC, revision 4, length 14 <7> [156.415739] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pixelformat: RGB <7> [156.415812] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] colorimetry: sRGB <7> [156.415883] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] bpc: 0 <7> [156.415952] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dynamic range: VESA range <7> [156.416021] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] content type: Not defined <7> [156.416089] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] scanline offset: 1 <7> [156.416169] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vblank delay: 0, framestart delay: 1, MSA timing delay: 0 <7> [156.416237] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: no, vmin: 1906, vmax: 2859, flipline: 1906, pipeline full: 0, guardband: 106 vsync start: 103, vsync end: 97 <7> [156.416304] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] vrr: vmin vblank: 1800, vmax vblank: 2753, vmin vtotal: 1906, vmax vtotal: 2859 <7> [156.416368] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] requested mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [156.416431] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] adjusted mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x48 0xa <7> [156.416494] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [156.416557] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe mode: "2880x1800": 60 347710 2880 2928 2960 3040 1800 1803 1809 1906 0x40 0xa <7> [156.416619] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] crtc timings: clock=347710, hd=2880 hb=2880-3040 hs=2928-2960 ht=3040, vd=1800 vb=1800-1906 vs=1803-1809 vt=1906, flags=0xa <7> [156.416681] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] port clock: 432000, pipe src: 2880x1800+0+0, pixel rate 347710 <7> [156.416741] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] linetime: 70, ips linetime: 0 <7> [156.416802] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [156.416862] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [156.416921] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] ips: 0, double wide: 0, drrs: 0 <7> [156.416980] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] dpll_hw_state: dpll: 0x69780, dpll_md: 0x42110, fp0: 0x1a2, fp1: 0x1000000 <7> [156.417038] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [156.417094] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [156.417163] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [156.417231] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [156.417301] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [156.417361] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [156.417422] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [156.417483] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [156.417543] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [156.417604] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [156.417662] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [156.417717] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [156.417773] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:32:plane 1A] fb: [FB:226] 2880x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7> [156.417830] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7> [156.417885] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] src: 2880.000000x1800.000000+0.000000+0.000000 dst: 2880x1800+0+0 <7> [156.417941] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:41:plane 2A] fb: [NOFB], visible: no <7> [156.417996] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:50:plane 3A] fb: [NOFB], visible: no <7> [156.418051] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:59:plane 4A] fb: [NOFB], visible: no <7> [156.418109] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:68:plane 5A] fb: [NOFB], visible: no <7> [156.418170] xe 0000:00:02.0: [drm:intel_crtc_state_dump [xe]] [PLANE:77:cursor A] fb: [NOFB], visible: no <7> [156.420020] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling PW_A <7> [156.420169] xe 0000:00:02.0: [drm:intel_set_cdclk [xe]] Pre changing CDCLK to 192000 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [156.420260] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 4 (mbus joined: no) <7> [156.420360] xe 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [xe]] aud_ts_cdclk set to M=60, N=480 <7> [156.420427] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:188:DDI A/PHY A] <7> [156.420485] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:197:DDI TC1/PHY TC1] <7> [156.420540] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:199:DP-MST A] <7> [156.420593] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:200:DP-MST B] <7> [156.420646] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:201:DP-MST C] <7> [156.420697] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:209:DDI TC2/PHY TC2] <7> [156.420748] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:211:DP-MST A] <7> [156.420798] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:212:DP-MST B] <7> [156.420848] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:213:DP-MST C] <7> [156.420897] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:217:DDI TC3/PHY TC3] <7> [156.420947] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:219:DP-MST A] <7> [156.420996] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:220:DP-MST B] <7> [156.421044] xe 0000:00:02.0: [drm:intel_modeset_verify_disabled [xe]] [ENCODER:221:DP-MST C] <7> [156.421093] xe 0000:00:02.0: [drm:gen9_dbuf_slices_update [xe]] Updating dbuf slices to 0xf <7> [156.421293] xe 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [xe]] Changing mbus joined: no -> yes (pipe: ) <7> [156.421368] xe 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [xe]] Updating dbuf ratio to 8 (mbus joined: yes) <7> [156.421439] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling AUX_A <7> [156.422232] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 turn panel power on <7> [156.422339] xe 0000:00:02.0: [drm:wait_panel_power_cycle [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 wait for panel power cycle (473 ms remaining) <7> [156.897434] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060 <7> [156.979827] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete <7> [156.980206] xe 0000:00:02.0: [drm:intel_pps_on_unlocked [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 wait for panel power on <7> [156.980495] xe 0000:00:02.0: [drm:wait_panel_status [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063 <7> [157.009127] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port F/TC#3: TC port mode reset (tbt-alt -> disconnected) <7> [157.009140] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) <7> [157.009161] xe 0000:00:02.0: [drm:intel_tc_port_reset_mode [xe]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) <7> [157.016590] xe 0000:00:02.0: [drm:icp_irq_handler [xe]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7> [157.017007] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] digital hpd on [ENCODER:188:DDI A/PHY A] - long <7> [157.017391] xe 0000:00:02.0: [drm:intel_hpd_irq_handler [xe]] Received HPD interrupt on PIN 4 - cnt: 20 <7> [157.017791] xe 0000:00:02.0: [drm:intel_dp_hpd_pulse [xe]] ignoring long hpd on eDP [ENCODER:188:DDI A/PHY A] <7> [157.252271] xe 0000:00:02.0: [drm:wait_panel_status [xe]] Wait complete <7> [157.254549] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 turning VDD on <7> [157.254994] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b <7> [157.258700] xe 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 1e 44 c1 00 00 01 c0 02 00 02 00 00 0b 80 <7> [157.260045] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:189:eDP-1][ENCODER:188:DDI A/PHY A][DPRX] Reloading eDP link rates <7> [157.261271] xe 0000:00:02.0: [drm:intel_dp_start_link_train [xe]] [CONNECTOR:189:eDP-1][ENCODER:188:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 05 <7> [157.262670] xe 0000:00:02.0: [drm:intel_dp_set_signal_levels [xe]] [CONNECTOR:189:eDP-1][ENCODER:188:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0 <7> [157.263987] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:189:eDP-1][ENCODER:188:DDI A/PHY A][DPRX] Using DP training pattern TPS1 <7> [157.265509] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:189:eDP-1][ENCODER:188:DDI A/PHY A][DPRX] Clock recovery OK <7> [157.265891] xe 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [xe]] [CONNECTOR:189:eDP-1][ENCODER:188:DDI A/PHY A][DPRX] Using DP training pattern TPS4 <7> [157.267579] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:189:eDP-1][ENCODER:188:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful <7> [157.267924] xe 0000:00:02.0: [drm:intel_dp_link_train_phy [xe]] [CONNECTOR:189:eDP-1][ENCODER:188:DDI A/PHY A][DPRX] Link Training passed at link rate = 432000, lane count = 4 <7> [157.268740] xe 0000:00:02.0: [drm:intel_enable_transcoder [xe]] enabling pipe A <7> [157.269209] xe 0000:00:02.0: [drm:intel_edp_backlight_on [xe]] <7> [157.269547] xe 0000:00:02.0: [drm:intel_backlight_enable [xe]] pipe A <7> [157.269899] xe 0000:00:02.0: [drm:intel_backlight_set_pwm_level [xe]] [CONNECTOR:189:eDP-1] set backlight PWM = 4518 <7> [157.271019] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] reserved 10600448 bytes of contiguous stolen space for FBC, limit: 2 <7> [157.271361] xe 0000:00:02.0: [drm:intel_fbc_update [xe]] Enabling FBC on [PLANE:32:plane 1A] <7> [157.286171] xe 0000:00:02.0: [drm:intel_psr_post_plane_update [xe]] Enabling PSR2 <7> [157.287909] xe 0000:00:02.0: [drm:verify_connector_state [xe]] [CONNECTOR:189:eDP-1] <7> [157.288324] xe 0000:00:02.0: [drm:intel_modeset_verify_crtc [xe]] [CRTC:82:pipe A] <7> [157.308187] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [157.308561] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [157.308879] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [157.572351] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [157.572641] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [157.604145] xe 0000:00:02.0: [drm:intel_power_well_disable [xe]] disabling DC_off <7> [157.604536] xe 0000:00:02.0: [drm:skl_enable_dc6 [xe]] Enabling DC6 <7> [157.604851] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 00 to 02 <7> [159.824922] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 turning VDD off <7> [159.825294] xe 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067 <7> [167.584902] xe 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:228] from all active usage due to RMFB ioctl <7> [167.585124] xe 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:32:plane 1A] because [FB:228] is removed <7> [167.585311] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] ddb ( 0 - 4054) -> ( 0 - 0), size 4054 -> 0 <7> [167.585616] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [167.585871] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] lines 2, 12, 12, 12, 11, 12, 0, 0, 0, 3, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [167.586211] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] blocks 49, 289, 289, 289, 265, 289, 0, 0, 63, 73, 87 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [167.586479] xe 0000:00:02.0: [drm:skl_compute_wm [xe]] [PLANE:32:plane 1A] min_ddb 55, 319, 319, 319, 293, 319, 0, 0, 64, 82, 88 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [167.586740] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] [CRTC:82:pipe A] data rate 0 num active planes 0 <7> [167.587126] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 0: max bw 23530 required 0 qgv_peak_bw: 38400 <7> [167.587484] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 1: max bw 36260 required 0 qgv_peak_bw: 38400 <7> [167.587838] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 2: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [167.588326] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] QGV point 3: max bw 38000 required 0 qgv_peak_bw: 38400 <7> [167.588705] xe 0000:00:02.0: [drm:intel_bw_atomic_check [xe]] Matching peaks QGV bw: 38400 for required data rate: 0 <7> [167.589580] xe 0000:00:02.0: [drm:intel_power_well_enable [xe]] enabling DC_off <7> [167.590141] xe 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [xe]] Setting DC state from 02 to 00 <7> [167.590820] xe 0000:00:02.0: [drm:intel_psr_disable_locked [xe]] Disabling PSR2 <7> [167.601350] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 turning VDD on <7> [167.601787] xe 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [xe]] [ENCODER:188:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f <7> [167.617852] xe 0000:00:02.0: [drm:__intel_fbc_disable [xe]] Disabling FBC on [PLANE:32:plane 1A] <6> [167.641885] [IGT] kms_flip: finished subtest A-eDP1, SUCCESS

Created at 2025-03-01 04:56:26