Hardware List

Results for igt@i915_module_load@load

Machine description: fi-kbl-x1275

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Duration	1.94 seconds
Igt-Version	IGT-Version: 1.30-g5d806121f (x86_64) (Linux: 6.14.0-rc6-CI_DRM_16274-ge2e6ad67ea05+ x86_64)
Out	Using IGT_SRANDOM=1741816438 for randomisation Starting subtest: load Opened device: /dev/dri/card0 Subtest load: SUCCESS (1.941s)
Err	Starting subtest: load Subtest load: SUCCESS (1.941s)
Dmesg	<6> [24.033773] [IGT] i915_module_load: executing <6> [24.319903] [IGT] i915_module_load: starting subtest load <4> [25.080366] <4> [25.080373] ******************************************************** <4> [25.080375] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [25.080376] <4> [25.080377] trace_printk() being used. Allocating extra memory. <4> [25.080378] <4> [25.080380] This means that this is a DEBUG kernel and it is <4> [25.080381] unsafe for production use. <4> [25.080382] <4> [25.080383] If you see this message and you are not debugging <4> [25.080384] the kernel, report this immediately to your vendor! <4> [25.080385] <4> [25.080386] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [25.080387] ******************************************************** <5> [25.107184] Setting dangerous option force_probe - tainting kernel <6> [25.115415] i915 0000:00:02.0: [drm] Found kabylake (device ID 591d) integrated display version 9.00 stepping C0 <7> [25.116856] i915 0000:00:02.0: [drm:intel_wopcm_init_early [i915]] WOPCM: 1024K <7> [25.117168] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no) <7> [25.117384] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint PCH <7> [25.117593] i915 0000:00:02.0: [drm:intel_dmc_wl_init [i915]] Sanitized enable_dmc_wl value: 0 (disabled) <7> [25.117892] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT <7> [25.118181] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing <7> [25.118363] i915 0000:00:02.0: [drm:intel_display_device_info_runtime_init [i915]] rawclk rate: 24000 kHz <7> [25.119420] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M <7> [25.119636] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M <7> [25.119796] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 32M <6> [25.119955] i915 0000:00:02.0: [drm] VT-d active for gfx access <6> [25.119973] i915 0000:00:02.0: vgaarb: deactivate vga console <6> [25.120440] i915 0000:00:02.0: [drm] Using Transparent Hugepages <7> [25.120517] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 8c700047 <7> [25.120743] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 32768K, usable: 31744K <7> [25.120923] i915 0000:00:02.0: [drm:intel_memory_regions_hw_probe [i915]] Memory region(0): system: 7441 MiB [mem 0x00000000-0x1d1179fff], io: n/a <7> [25.121074] i915 0000:00:02.0: [drm:intel_memory_regions_hw_probe [i915]] Memory region(5): stolen-system: 31 MiB [mem 0x8a800000-0x8c6fffff], io: n/a <7> [25.121432] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x71f90018 <7> [25.121701] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0 <7> [25.121921] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported <7> [25.122118] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x <7> [25.122307] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported <7> [25.128861] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483 <7> [25.129065] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported <7> [25.129256] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported <7> [25.129446] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4) <7> [25.129736] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4 <7> [25.129889] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no <7> [25.130040] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [25.130218] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no <7> [25.130388] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no <7> [25.130571] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [25.130722] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no <7> [25.130872] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes <7> [25.131021] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] Num qgv points 0 <7> [25.131173] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2 <7> [25.131322] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] Watermark level 0 adjustment needed: no <7> [25.132188] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz <7> [25.132414] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 196 <7> [25.132664] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7) <7> [25.132886] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5) <7> [25.133088] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100) <7> [25.133288] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19) <7> [25.133555] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 280, min size 848) <7> [25.133788] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 24, min size 34) <7> [25.134044] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148) <7> [25.134244] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366) <7> [25.134441] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305) <7> [25.134679] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 136) <7> [25.134902] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0 <7> [25.135097] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2 <7> [25.135292] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x78c6 <7> [25.135534] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6 <7> [25.135757] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6 <7> [25.135957] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping <7> [25.136151] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [25.136346] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0 <7> [25.136577] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [25.136821] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 3 <7> [25.137013] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [25.137221] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 3 <7> [25.137426] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02 <7> [25.137665] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [25.137917] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [25.138124] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO <7> [25.138322] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [25.138702] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz <7> [25.138898] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max dotclock rate: 675000 kHz <7> [25.139107] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [25.139341] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [25.139581] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [25.139800] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [25.140006] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <6> [25.140238] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io+mem:owns=io+mem <7> [25.140279] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E <7> [25.140521] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B <7> [25.140765] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C <7> [25.140980] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D <7> [25.141211] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin <7> [25.142585] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1 <7> [25.143198] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV <7> [25.143495] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us <7> [25.143759] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec) <7> [25.143951] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec) <7> [25.144170] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec) <7> [25.144360] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec) <7> [25.144591] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec) <7> [25.144865] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec) <7> [25.145179] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec) <7> [25.145430] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec) <7> [25.148764] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available. <7> [25.150857] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0 <7> [25.151182] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:98:DDI A/PHY A] Using AUX CH A (VBT) <7> [25.151492] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:98:DDI A/PHY A] <7> [25.155814] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] DMC 0: <7> [25.156040] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] mmio[0]: 0x8f074 = 0x2fc0 <7> [25.156237] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] mmio[1]: 0x8f004 = 0xb40068 (EVT_HTP) <7> [25.156433] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] mmio[2]: 0x8f034 = 0xc003b400 (EVT_CTL) <7> [25.156511] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0) <7> [25.156744] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2 <6> [25.157041] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4) <7> [25.156957] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2 <7> [25.157167] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is static <7> [25.157375] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa <7> [25.157613] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300 <7> [25.157822] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel manufacturer name: MS_, product code: 3, serial number: 3, year of manufacture: 2002 <7> [25.158016] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName <7> [25.158210] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz <7> [25.158418] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 0, level 255, controller 0 <7> [25.158654] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:1 <7> [25.158903] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:98:DDI A/PHY A] initial power sequencer: PPS 0 <7> [25.159211] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios power_up 0 backlight_on 0 backlight_off 0 power_down 0 power_cycle 0 <7> [25.159397] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000 <7> [25.159622] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100 <7> [25.159806] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 500 <7> [25.159990] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [25.160245] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06 <7> [25.160739] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 turning VDD on <7> [25.161028] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining) <7> [25.161284] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000 <7> [25.161516] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [25.161776] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008 <7> [25.161981] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 panel power wasn't enabled <7> [25.376470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.387469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.398469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.409473] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.420469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.431471] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.442469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.453470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.464469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.475468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.486468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.497470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.508468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.519468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.530468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.541471] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.552468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.563468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.574468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.585470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.596470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.607470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.618469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.629470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.640468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.651468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.662468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.673470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.684470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.695475] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.706469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.717470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.717714] i915 0000:00:02.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110 <7> [25.728468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.739468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.750468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.761470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.772468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.783468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.794468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.805470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.816468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.827469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.838468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.849468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.860468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.871472] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.882470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.893477] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.904469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.915469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.926468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.937469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.948468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.959469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.970468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.981469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [25.992470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [26.003468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [26.014470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [26.025469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [26.036469] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [26.047468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [26.058468] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [26.069470] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [26.069714] i915 0000:00:02.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110 <6> [26.069729] i915 0000:00:02.0: [drm] [ENCODER:98:DDI A/PHY A] failed to retrieve link info, disabling eDP <7> [26.069761] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 turning VDD off <7> [26.070013] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:98:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000 <7> [26.070322] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:98:DDI B/PHY B] Using AUX CH B (VBT) <7> [26.070554] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:98:DDI B/PHY B] <7> [26.071139] i915 0000:00:02.0: [drm:intel_psr_init [i915]] PSR condition failed: Port not supported <7> [26.071352] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:110:DDI C/PHY C] Using AUX CH C (VBT) <7> [26.071594] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:110:DDI C/PHY C] <7> [26.071952] i915 0000:00:02.0: [drm:intel_psr_init [i915]] PSR condition failed: Port not supported <7> [26.072158] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:110:DDI C/PHY C] <7> [26.072345] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:110:DDI C/PHY C] Using DDC pin 0x4 (VBT) <7> [26.073023] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:53:pipe A] hw state readout: disabled <7> [26.073274] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:75:pipe B] hw state readout: disabled <7> [26.073554] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:97:pipe C] hw state readout: disabled <7> [26.073761] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:32:plane 1A] hw state readout: disabled, pipe A <7> [26.073992] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A <7> [26.074198] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:48:cursor A] hw state readout: disabled, pipe A <7> [26.074444] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:54:plane 1B] hw state readout: disabled, pipe B <7> [26.074728] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:62:plane 2B] hw state readout: disabled, pipe B <7> [26.074934] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:70:cursor B] hw state readout: disabled, pipe B <7> [26.075138] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 1C] hw state readout: disabled, pipe C <7> [26.075341] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:84:plane 2C] hw state readout: disabled, pipe C <7> [26.075592] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:92:cursor C] hw state readout: disabled, pipe C <7> [26.075800] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:98:DDI B/PHY B] hw state readout: disabled, pipe A <7> [26.075992] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:100:DP-MST A] hw state readout: disabled, pipe A <7> [26.076185] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:101:DP-MST B] hw state readout: disabled, pipe B <7> [26.076377] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:102:DP-MST C] hw state readout: disabled, pipe C <7> [26.076618] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:110:DDI C/PHY C] hw state readout: disabled, pipe A <7> [26.076811] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:112:DP-MST A] hw state readout: disabled, pipe A <7> [26.077001] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:113:DP-MST B] hw state readout: disabled, pipe B <7> [26.077193] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:114:DP-MST C] hw state readout: disabled, pipe C <7> [26.077400] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1 <7> [26.077706] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [26.077928] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0 <7> [26.078192] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0 <7> [26.078673] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:99:DP-1] hw state readout: disabled <7> [26.078895] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:111:DP-2] hw state readout: disabled <7> [26.079110] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:117:HDMI-A-1] hw state readout: disabled <7> [26.079303] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:32:plane 1A] min_cdclk 0 kHz <7> [26.079556] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz <7> [26.079748] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:48:cursor A] min_cdclk 0 kHz <7> [26.079939] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:54:plane 1B] min_cdclk 0 kHz <7> [26.080131] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:62:plane 2B] min_cdclk 0 kHz <7> [26.080323] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:70:cursor B] min_cdclk 0 kHz <7> [26.080558] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 1C] min_cdclk 0 kHz <7> [26.080750] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:84:plane 2C] min_cdclk 0 kHz <7> [26.080941] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:92:cursor C] min_cdclk 0 kHz <7> [26.081139] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:53:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [26.081332] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:75:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [26.081559] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:97:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [26.081902] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:53:pipe A] enable: no [setup_hw_state] <7> [26.082120] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:75:pipe B] enable: no [setup_hw_state] <7> [26.082318] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:97:pipe C] enable: no [setup_hw_state] <7> [26.082554] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling <7> [26.083032] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture <7> [26.083194] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000] <7> [26.083364] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0 <7> [26.083665] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 6 GT workarounds on global <7> [26.084977] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 8 engine workarounds on rcs'0 <7> [26.085167] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 5 whitelist workarounds on rcs'0 <7> [26.085400] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 14 context workarounds on rcs'0 <7> [26.097657] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed rcs'0 to rcs0 <7> [26.097843] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed bcs'0 to bcs0 <7> [26.098002] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed vcs'0 to vcs0 <7> [26.098160] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed vecs'0 to vecs0 <7> [26.098796] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV <7> [26.102828] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:99:DP-1] adding connector to sysfs <7> [26.104077] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1 <7> [26.106844] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:99:DP-1] generating connector hotplug event <7> [26.106926] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:111:DP-2] adding connector to sysfs <7> [26.107366] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DDI C/PHY C bus for card0-DP-2 <7> [26.108654] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:111:DP-2] generating connector hotplug event <7> [26.108737] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:117:HDMI-A-1] adding connector to sysfs <7> [26.109451] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:117:HDMI-A-1] generating connector hotplug event <6> [26.109550] [drm] Initialized i915 1.6.0 for 0000:00:02.0 on minor 0 <7> [26.111854] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected <6> [26.127305] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6> [26.131243] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input6 <7> [26.132944] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10) <7> [26.135265] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:99:DP-1] <7> [26.135311] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:53:pipe A] not active, skipping <7> [26.135527] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:75:pipe B] not active, skipping <7> [26.135723] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:97:pipe C] not active, skipping <7> [26.135917] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] no active fbs found, not using BIOS config <7> [26.136145] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [26.136660] i915 0000:00:02.0: [drm:drm_client_modeset_probe] <7> [26.140569] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:99:DP-1] status updated from unknown to disconnected (epoch counter 0->1) <7> [26.140784] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-2] <7> [26.142687] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [26.143929] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [26.145752] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:111:DP-2] status updated from unknown to disconnected (epoch counter 0->1) <7> [26.145964] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:117:HDMI-A-1] <7> [26.146576] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [26.146853] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [26.147882] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [26.148194] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [26.148200] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [26.148467] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [26.152884] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [26.152889] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [26.153116] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:117:HDMI-A-1] status updated from unknown to disconnected (epoch counter 0->1) <7> [26.153319] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event <7> [26.153422] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:99:DP-1] <7> [26.153446] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:99:DP-1] <7> [26.158579] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:99:DP-1] disconnected <7> [26.158597] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:111:DP-2] <7> [26.158610] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-2] <7> [26.160486] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [26.161725] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [26.163398] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:111:DP-2] disconnected <7> [26.163415] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:117:HDMI-A-1] <7> [26.163428] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:117:HDMI-A-1] <7> [26.164352] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [26.164584] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [26.165011] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [26.165242] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [26.165246] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [26.165439] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [26.169858] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [26.169863] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [26.170081] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:117:HDMI-A-1] disconnected <7> [26.170098] i915 0000:00:02.0: [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [26.170105] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:99:DP-1] enabled? no <7> [26.170108] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:DP-2] enabled? no <7> [26.170110] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:117:HDMI-A-1] enabled? no <7> [26.170234] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [26.170247] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [26.170272] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane <6> [26.170293] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [26.171347] i915 0000:00:02.0: [drm:drm_client_modeset_probe] <7> [26.171281] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: display version: 9 <7> [26.171581] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: display stepping: C0 <7> [26.171774] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:99:DP-1] <7> [26.171796] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: cursor_needs_physical: no <7> [26.171800] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:99:DP-1] <7> [26.172008] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_cdclk_crawl: no <7> [26.172217] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_cdclk_squash: no <7> [26.172412] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_ddi: yes <7> [26.172644] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dp_mst: yes <7> [26.172916] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dsb: no <7> [26.173194] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_fpga_dbg: yes <7> [26.173412] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_gmch: no <7> [26.173787] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hotplug: yes <7> [26.173983] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hti: no <7> [26.174180] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_ipc: yes <7> [26.174377] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_overlay: no <7> [26.174695] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_psr: yes <7> [26.174999] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_psr_hw_tracking: yes <7> [26.175226] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: overlay_needs_physical: no <7> [26.175520] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: supports_tv: no <7> [26.175797] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hdcp: yes <7> [26.175993] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dmc: yes <7> [26.176188] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dsc: no <7> [26.176384] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: rawclk rate: 24000 kHz <7> [26.176599] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:99:DP-1] disconnected <7> [26.176624] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:111:DP-2] <7> [26.176645] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-2] <7> [26.177077] [drm:intel_dsm_detect.isra.0 [i915]] no _DSM method for intel device <7> [26.177304] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D <7> [26.177587] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C <7> [26.177818] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B <7> [26.178036] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E <7> [26.178288] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: pciid=0x591d rev=0x04 platform=KABYLAKE (subplatform=0x0) gen=9 <7> [26.178452] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: graphics version: 9 <7> [26.178644] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: media version: 9 <7> [26.178826] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: graphics stepping: F0 <7> [26.179007] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: media stepping: F0 <7> [26.179191] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [26.179182] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: gt: 2 <7> [26.179359] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: memory-regions: 0x21 <7> [26.179579] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: page-sizes: 0x11000 <7> [26.179764] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: platform: KABYLAKE <7> [26.179936] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: ppgtt-size: 48 <7> [26.180117] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: ppgtt-type: 2 <7> [26.180298] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: dma_mask_size: 39 <7> [26.180523] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [26.180485] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: is_mobile: no <7> [26.180632] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: require_force_probe: no <7> [26.180806] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: is_dgfx: no <7> [26.180987] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_64bit_reloc: yes <7> [26.181143] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_64k_pages: no <7> [26.181316] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: gpu_reset_clobbers_display: no <7> [26.181503] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_reset_engine: yes <7> [26.181656] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_3d_pipeline: yes <7> [26.181837] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_flat_ccs: no <7> [26.182014] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_global_mocs: no <7> [26.182169] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_gmd_id: no <7> [26.182352] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_gt_uc: yes <7> [26.182518] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:111:DP-2] disconnected <7> [26.182543] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:117:HDMI-A-1] <7> [26.182530] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_heci_pxp: no <7> [26.182564] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:117:HDMI-A-1] <7> [26.182693] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_heci_gscfi: no <7> [26.182866] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_guc_deprivilege: no <7> [26.183025] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_guc_tlb_invalidation: no <7> [26.183170] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_l3_ccs_read: no <7> [26.183353] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_l3_dpf: no <7> [26.183369] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [26.183532] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_llc: yes <7> [26.183693] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_logical_ring_contexts: yes <7> [26.183695] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [26.183865] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_logical_ring_elsq: no <7> [26.184011] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_media_ratio_mode: no <7> [26.184172] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_mslice_steering: no <7> [26.184320] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oa_bpc_reporting: no <7> [26.184475] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oa_slice_contrib_limits: no <7> [26.184581] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [26.184703] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oam: no <7> [26.184890] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [26.184849] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_one_eu_per_fuse_bit: no <7> [26.184896] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [26.184994] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_pxp: no <7> [26.185138] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rc6: yes <7> [26.185160] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [26.185283] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rc6p: no <7> [26.185428] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rps: yes <7> [26.185707] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_runtime_pm: yes <7> [26.185946] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_snoop: no <7> [26.186166] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_coherent_ggtt: yes <7> [26.186387] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: tuning_thread_rr_after_dep: no <7> [26.186618] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: unfenced_needs_alignment: no <7> [26.186859] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: hws_needs_physical: no <7> [26.187058] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_pooled_eu: no <7> [26.187203] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: iommu: enabled <7> [26.187369] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: available engines: 40403 <7> [26.187550] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice total: 1, mask=0001 <7> [26.187733] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: subslice total: 3 <7> [26.187880] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice0: 3 subslices, mask=00000007 <7> [26.188027] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice1: 0 subslices, mask=00000000 <7> [26.188173] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice2: 0 subslices, mask=00000000 <7> [26.188319] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: EU total: 24 <7> [26.188470] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: EU per subslice: 8 <7> [26.188701] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has slice power gating: no <7> [26.188846] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has subslice power gating: no <7> [26.188992] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has EU power gating: yes <6> [26.189138] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled <6> [26.189139] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled <6> [26.189141] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled <7> [26.189850] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [26.189858] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [26.190147] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:117:HDMI-A-1] disconnected <7> [26.190170] i915 0000:00:02.0: [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [26.190180] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:99:DP-1] enabled? no <7> [26.190185] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:DP-2] enabled? no <7> [26.190189] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:117:HDMI-A-1] enabled? no <7> [26.190328] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [26.190348] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [26.190387] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane <6> [26.190414] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [26.190418] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0 <7> [26.247115] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [26.248036] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [26.248597] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [26.248664] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [26.261057] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <6> [26.261130] [IGT] i915_module_load: finished subtest load, SUCCESS <6> [26.261215] [IGT] i915_module_load: exiting, ret=0

Created at 2025-03-12 23:09:31