Results for igt@i915_module_load@load

Machine description: fi-kbl-guc

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 1.03 seconds
Igt-Version 
IGT-Version: 1.30-g5d806121f (x86_64) (Linux: 6.14.0-rc6-CI_DRM_16274-ge2e6ad67ea05+ x86_64)
Out 
Using IGT_SRANDOM=1741816371 for randomisation
Starting subtest: load
Opened device: /dev/dri/card0
Subtest load: SUCCESS (1.027s)
Err 
Starting subtest: load
Subtest load: SUCCESS (1.027s)
Dmesg
<6> [37.024898] [IGT] i915_module_load: executing
<6> [37.315697] [IGT] i915_module_load: starting subtest load
<4> [38.058769]
<4> [38.058776] **********************************************************
<4> [38.058778] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
<4> [38.058779] ** **
<4> [38.058781] ** trace_printk() being used. Allocating extra memory. **
<4> [38.058782] ** **
<4> [38.058784] ** This means that this is a DEBUG kernel and it is **
<4> [38.058785] ** unsafe for production use. **
<4> [38.058787] ** **
<4> [38.058788] ** If you see this message and you are not debugging **
<4> [38.058790] ** the kernel, report this immediately to your vendor! **
<4> [38.058791] ** **
<4> [38.058792] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
<4> [38.058794] **********************************************************
<5> [38.086438] Setting dangerous option force_probe - tainting kernel
<5> [38.086515] Setting dangerous option enable_guc - tainting kernel
<6> [38.096140] i915 0000:00:02.0: [drm] Found kabylake (device ID 5912) integrated display version 9.00 stepping C0
<7> [38.097726] i915 0000:00:02.0: [drm:intel_wopcm_init_early [i915]] WOPCM: 1024K
<7> [38.098064] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:no huc:yes slpc:no)
<6> [38.098257] i915 0000:00:02.0: [drm] GT0: Incompatible option enable_guc=3 - GuC submission is N/A
<7> [38.098266] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint PCH
<7> [38.098413] i915 0000:00:02.0: [drm:intel_dmc_wl_init [i915]] Sanitized enable_dmc_wl value: 0 (disabled)
<7> [38.098684] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [38.099016] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [38.099247] i915 0000:00:02.0: [drm:intel_display_device_info_runtime_init [i915]] rawclk rate: 24000 kHz
<7> [38.100214] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [38.100369] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [38.100518] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M
<6> [38.100665] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [38.101019] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [38.101589] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<7> [38.101613] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = c7f00047
<7> [38.101791] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K
<7> [38.101958] i915 0000:00:02.0: [drm:intel_memory_regions_hw_probe [i915]] Memory region(0): system: 7736 MiB [mem 0x00000000-0x1e3894fff], io: n/a
<7> [38.102114] i915 0000:00:02.0: [drm:intel_memory_regions_hw_probe [i915]] Memory region(5): stolen-system: 63 MiB [mem 0xc4000000-0xc7efffff], io: n/a
<7> [38.102539] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0xc2d24018
<7> [38.102755] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0
<7> [38.102933] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [38.103204] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [38.103383] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [38.108811] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483
<7> [38.109023] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [38.109213] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [38.109405] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [38.109584] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4
<7> [38.109727] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no
<7> [38.109866] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [38.110004] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no
<7> [38.110156] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no
<7> [38.110312] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [38.110452] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no
<7> [38.110592] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [38.110731] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] Num qgv points 0
<7> [38.110871] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [38.111009] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] Watermark level 0 adjustment needed: no
<7> [38.111754] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [38.111988] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 206
<7> [38.112460] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [38.112713] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)
<7> [38.112923] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [38.113182] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [38.113441] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 848)
<7> [38.113661] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)
<7> [38.113884] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [38.114144] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)
<7> [38.114344] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [38.114588] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 136)
<7> [38.114828] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
<7> [38.115020] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [38.115240] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2
<7> [38.115500] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2
<7> [38.115696] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6
<7> [38.115936] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [38.116192] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [38.116425] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 4
<7> [38.116617] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [38.116852] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8
<7> [38.117087] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [38.117296] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0
<7> [38.117556] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02
<7> [38.117765] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [38.118068] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [38.118283] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO
<7> [38.118526] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [38.119391] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz
<7> [38.119618] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max dotclock rate: 675000 kHz
<7> [38.119813] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [38.120042] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [38.120266] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [38.120516] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [38.120709] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<6> [38.120934] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io+mem:owns=io+mem
<7> [38.120999] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [38.121268] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [38.121474] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [38.121678] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [38.121968] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin
<7> [38.123042] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [38.124355] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV
<7> [38.124628] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us
<7> [38.124825] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [38.125005] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [38.125192] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [38.125470] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [38.125722] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [38.125956] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [38.126167] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [38.126344] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [38.129994] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.
<7> [38.131994] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [38.132386] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:98:DDI B/PHY B]
<7> [38.132622] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:98:DDI B/PHY B] Using DDC pin 0x5 (VBT)
<7> [38.133360] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] DMC 0:
<7> [38.133625] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] mmio[0]: 0x8f074 = 0x2fc0
<7> [38.133864] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:108:DDI C/PHY C]
<7> [38.133876] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] mmio[1]: 0x8f004 = 0xb40068 (EVT_HTP)
<7> [38.134168] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:108:DDI C/PHY C] Using DDC pin 0x4 (VBT)
<7> [38.134174] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] mmio[2]: 0x8f034 = 0xc003b400 (EVT_CTL)
<7> [38.134639] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:112:DDI E/PHY E] Using AUX CH A (VBT)
<6> [38.134756] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)
<7> [38.134867] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:112:DDI E/PHY E]
<7> [38.135255] i915 0000:00:02.0: [drm:intel_psr_init [i915]] PSR condition failed: Port not supported
<7> [38.135944] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:53:pipe A] hw state readout: disabled
<7> [38.136300] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:75:pipe B] hw state readout: disabled
<7> [38.136573] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:97:pipe C] hw state readout: disabled
<7> [38.136787] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:32:plane 1A] hw state readout: disabled, pipe A
<7> [38.136998] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A
<7> [38.137219] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:48:cursor A] hw state readout: disabled, pipe A
<7> [38.137455] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:54:plane 1B] hw state readout: disabled, pipe B
<7> [38.137670] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:62:plane 2B] hw state readout: disabled, pipe B
<7> [38.137887] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:70:cursor B] hw state readout: disabled, pipe B
<7> [38.138219] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 1C] hw state readout: disabled, pipe C
<7> [38.138416] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:84:plane 2C] hw state readout: disabled, pipe C
<7> [38.138623] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:92:cursor C] hw state readout: disabled, pipe C
<7> [38.138842] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:98:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [38.139036] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DDI C/PHY C] hw state readout: disabled, pipe A
<7> [38.139293] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:112:DDI E/PHY E] hw state readout: disabled, pipe A
<7> [38.139496] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1
<7> [38.139716] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [38.139914] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [38.140134] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [38.140449] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:99:HDMI-A-1] hw state readout: disabled
<7> [38.140678] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:109:HDMI-A-2] hw state readout: disabled
<7> [38.140906] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:113:DP-1] hw state readout: disabled
<7> [38.141097] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:32:plane 1A] min_cdclk 0 kHz
<7> [38.141284] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz
<7> [38.141475] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:48:cursor A] min_cdclk 0 kHz
<7> [38.141671] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:54:plane 1B] min_cdclk 0 kHz
<7> [38.141851] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:62:plane 2B] min_cdclk 0 kHz
<7> [38.142035] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:70:cursor B] min_cdclk 0 kHz
<7> [38.142271] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 1C] min_cdclk 0 kHz
<7> [38.142457] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:84:plane 2C] min_cdclk 0 kHz
<7> [38.142644] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:92:cursor C] min_cdclk 0 kHz
<7> [38.142843] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:53:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [38.143023] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:75:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [38.143218] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:97:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [38.143503] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:53:pipe A] enable: no [setup_hw_state]
<7> [38.143690] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:75:pipe B] enable: no [setup_hw_state]
<7> [38.143879] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:97:pipe C] enable: no [setup_hw_state]
<7> [38.144097] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling
<7> [38.149507] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] Calculated GuC WOPCM [240K, 784K)
<7> [38.149688] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [38.149841] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000]
<7> [38.149998] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0
<7> [38.150196] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 6 GT workarounds on global
<7> [38.151526] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 8 engine workarounds on rcs'0
<7> [38.151708] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 5 whitelist workarounds on rcs'0
<7> [38.151886] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 14 context workarounds on rcs'0
<7> [38.158188] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3)
<7> [38.158410] i915 0000:00:02.0: [drm:intel_guc_capture_init [i915]] GT0: GUC: capture found 6 ext-regs.
<7> [38.158611] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset
<7> [38.197055] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0xc404f
<7> [38.197315] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x0
<7> [38.197559] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4000
<7> [38.197731] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3
<7> [38.197901] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0x98a
<7> [38.198102] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x59120004
<7> [38.198277] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0
<7> [38.198456] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0
<7> [38.198637] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0
<7> [38.198815] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0
<7> [38.198989] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0
<7> [38.199177] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0
<7> [38.199351] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0
<7> [38.199524] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0
<7> [38.199721] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no
<6> [38.200978] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [38.200982] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [38.215213] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 10ms, freq = 100MHz -> 100MHz vs 1150MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [38.216394] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [38.228211] i915 0000:00:02.0: [drm:intel_huc_wait_for_auth_complete [i915]] GT0: HuC: auth took 11ms, freq = 100MHz -> 100MHz vs 1150MHz, status = 0x0000D3B0, count = 0, ret = 0
<6> [38.228396] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads
<6> [38.228399] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [38.228401] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<7> [38.237262] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed rcs'0 to rcs0
<7> [38.237429] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed bcs'0 to bcs0
<7> [38.237577] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed vcs'0 to vcs0
<7> [38.237724] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed vecs'0 to vecs0
<7> [38.237978] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind
<6> [38.238197] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
<7> [38.238659] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV
<7> [38.243031] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:99:HDMI-A-1] adding connector to sysfs
<7> [38.244324] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:99:HDMI-A-1] generating connector hotplug event
<7> [38.244477] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:109:HDMI-A-2] adding connector to sysfs
<7> [38.244989] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:109:HDMI-A-2] generating connector hotplug event
<7> [38.245084] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:113:DP-1] adding connector to sysfs
<7> [38.245840] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI E/PHY E bus for card0-DP-1
<7> [38.248139] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:113:DP-1] generating connector hotplug event
<6> [38.248194] [drm] Initialized i915 1.6.0 for 0000:00:02.0 on minor 0
<7> [38.250629] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected
<6> [38.268378] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [38.270007] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input4
<7> [38.272518] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)
<7> [38.273263] check_position_fix: snd_hda_intel 0000:00:1f.3: Using SKL position fix
<6> [38.274348] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops intel_audio_component_bind_ops [i915])
<7> [38.275323] i915 0000:00:02.0: [drm:intel_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [38.275411] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:99:HDMI-A-1]
<7> [38.276085] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:53:pipe A] not active, skipping
<7> [38.276342] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:75:pipe B] not active, skipping
<7> [38.276590] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:97:pipe C] not active, skipping
<7> [38.276838] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] no active fbs found, not using BIOS config
<7> [38.277150] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [38.277808] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [38.277728] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [38.277986] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [38.278923] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [38.279222] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [38.279229] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [38.279471] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [38.280258] azx_first_init: snd_hda_intel 0000:00:1f.3: chipset global capabilities = 0x9701
<7> [38.280936] azx_init_pci: snd_hda_intel 0000:00:1f.3: Clearing TCSEL
<7> [38.280962] azx_init_pci: snd_hda_intel 0000:00:1f.3: SCH snoop: Enabled
<7> [38.282488] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [38.282495] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [38.282762] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:99:HDMI-A-1] status updated from unknown to disconnected (epoch counter 0->1)
<7> [38.282954] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:109:HDMI-A-2]
<7> [38.283558] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [38.283736] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [38.284101] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [38.284298] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [38.284303] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [38.284476] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [38.287338] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [38.287344] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [38.287536] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:109:HDMI-A-2] status updated from unknown to disconnected (epoch counter 0->1)
<7> [38.287721] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:113:DP-1]
<7> [38.292204] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:113:DP-1] status updated from unknown to disconnected (epoch counter 0->1)
<7> [38.292429] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [38.292535] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:99:HDMI-A-1]
<7> [38.292558] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:99:HDMI-A-1]
<7> [38.293165] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [38.293345] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [38.293956] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [38.294268] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [38.294274] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [38.294474] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [38.297776] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [38.297781] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [38.297984] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:99:HDMI-A-1] disconnected
<7> [38.298001] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:HDMI-A-2]
<7> [38.298014] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:109:HDMI-A-2]
<7> [38.298448] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [38.298651] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [38.299037] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [38.299295] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [38.299300] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [38.299532] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [38.302502] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [38.302508] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [38.302711] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:HDMI-A-2] disconnected
<7> [38.302729] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:DP-1]
<7> [38.302742] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:113:DP-1]
<7> [38.307106] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:DP-1] disconnected
<7> [38.307134] i915 0000:00:02.0: [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [38.307146] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:99:HDMI-A-1] enabled? no
<7> [38.307151] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:109:HDMI-A-2] enabled? no
<7> [38.307156] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:113:DP-1] enabled? no
<7> [38.307280] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [38.307297] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [38.307330] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [38.307354] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [38.308403] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [38.308303] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: display version: 9
<7> [38.308605] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: display stepping: C0
<7> [38.308745] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:99:HDMI-A-1]
<7> [38.308771] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:99:HDMI-A-1]
<7> [38.308861] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: cursor_needs_physical: no
<7> [38.309116] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_cdclk_crawl: no
<7> [38.309365] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_cdclk_squash: no
<7> [38.309588] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_ddi: yes
<7> [38.309776] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [38.309812] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dp_mst: yes
<7> [38.310028] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [38.310022] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dsb: no
<7> [38.310295] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_fpga_dbg: yes
<7> [38.310549] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_gmch: no
<7> [38.310808] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hotplug: yes
<7> [38.310869] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [38.311162] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [38.311078] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hti: no
<7> [38.311170] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [38.311329] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_ipc: yes
<7> [38.311413] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [38.311572] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_overlay: no
<7> [38.311778] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_psr: yes
<7> [38.312025] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_psr_hw_tracking: yes
<7> [38.312291] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: overlay_needs_physical: no
<7> [38.312545] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: supports_tv: no
<7> [38.312804] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hdcp: yes
<7> [38.313072] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dmc: yes
<7> [38.313331] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dsc: no
<7> [38.313588] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: rawclk rate: 24000 kHz
<7> [38.314400] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [38.314409] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [38.314697] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:99:HDMI-A-1] disconnected
<7> [38.314720] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:HDMI-A-2]
<7> [38.314619] [drm:intel_dsm_detect.isra.0 [i915]] no _DSM method for intel device
<7> [38.314739] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:109:HDMI-A-2]
<7> [38.314869] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D
<7> [38.315101] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C
<7> [38.315312] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B
<7> [38.315538] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E
<7> [38.315877] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: pciid=0x5912 rev=0x04 platform=KABYLAKE (subplatform=0x0) gen=9
<7> [38.316066] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: graphics version: 9
<7> [38.316118] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [38.316266] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: media version: 9
<7> [38.316327] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [38.316410] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: graphics stepping: F0
<7> [38.316573] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: media stepping: F0
<7> [38.316772] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: gt: 2
<7> [38.316780] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [38.316953] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: memory-regions: 0x21
<7> [38.317084] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [38.317091] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [38.317149] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: page-sizes: 0x11000
<7> [38.317293] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: platform: KABYLAKE
<7> [38.317327] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [38.317452] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: ppgtt-size: 48
<7> [38.317630] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: ppgtt-type: 2
<7> [38.317788] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: dma_mask_size: 39
<7> [38.317925] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: is_mobile: no
<7> [38.318081] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: require_force_probe: no
<7> [38.318247] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: is_dgfx: no
<7> [38.318415] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_64bit_reloc: yes
<7> [38.318554] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_64k_pages: no
<7> [38.318698] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: gpu_reset_clobbers_display: no
<7> [38.318843] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_reset_engine: yes
<7> [38.318998] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_3d_pipeline: yes
<7> [38.319147] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_flat_ccs: no
<7> [38.319305] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_global_mocs: no
<7> [38.319473] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_gmd_id: no
<7> [38.319610] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_gt_uc: yes
<7> [38.319757] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_heci_pxp: no
<7> [38.319901] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_heci_gscfi: no
<7> [38.320072] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_guc_deprivilege: no
<7> [38.320224] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_guc_tlb_invalidation: no
<7> [38.320329] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [38.320366] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_l3_ccs_read: no
<7> [38.320336] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [38.320523] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_l3_dpf: no
<7> [38.320593] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:HDMI-A-2] disconnected
<7> [38.320615] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:DP-1]
<7> [38.320630] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:113:DP-1]
<7> [38.320677] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_llc: yes
<7> [38.320853] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_logical_ring_contexts: yes
<7> [38.321037] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_logical_ring_elsq: no
<7> [38.321228] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_media_ratio_mode: no
<7> [38.321424] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_mslice_steering: no
<7> [38.321622] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oa_bpc_reporting: no
<7> [38.321767] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oa_slice_contrib_limits: no
<7> [38.321903] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oam: no
<6> [38.322146] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC887-VD: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
<7> [38.322052] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_one_eu_per_fuse_bit: no
<6> [38.322151] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<6> [38.322153] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)
<6> [38.322155] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
<6> [38.322157] snd_hda_codec_realtek hdaudioC0D0: dig-out=0x11/0x0
<6> [38.322159] snd_hda_codec_realtek hdaudioC0D0: inputs:
<6> [38.322162] snd_hda_codec_realtek hdaudioC0D0: Rear Mic=0x18
<6> [38.322166] snd_hda_codec_realtek hdaudioC0D0: Front Mic=0x19
<6> [38.322172] snd_hda_codec_realtek hdaudioC0D0: Line=0x1a
<7> [38.322243] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_pxp: no
<7> [38.322412] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rc6: yes
<7> [38.322574] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rc6p: no
<7> [38.322709] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rps: yes
<7> [38.322845] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_runtime_pm: yes
<7> [38.323010] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_snoop: no
<7> [38.323270] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_coherent_ggtt: yes
<7> [38.323417] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: tuning_thread_rr_after_dep: no
<7> [38.323558] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: unfenced_needs_alignment: no
<7> [38.323738] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: hws_needs_physical: no
<7> [38.323905] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_pooled_eu: no
<7> [38.324056] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: iommu: enabled
<7> [38.324215] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: available engines: 40403
<7> [38.324395] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice total: 1, mask=0001
<7> [38.324531] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: subslice total: 3
<7> [38.324667] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice0: 3 subslices, mask=00000007
<7> [38.324823] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice1: 0 subslices, mask=00000000
<7> [38.324998] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice2: 0 subslices, mask=00000000
<7> [38.325116] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:DP-1] disconnected
<7> [38.325133] i915 0000:00:02.0: [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [38.325141] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:99:HDMI-A-1] enabled? no
<7> [38.325146] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:109:HDMI-A-2] enabled? no
<7> [38.325150] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:113:DP-1] enabled? no
<7> [38.325189] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: EU total: 24
<7> [38.325270] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [38.325288] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [38.325325] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [38.325342] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [38.325347] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [38.325345] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: EU per subslice: 8
<7> [38.325520] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has slice power gating: no
<7> [38.325695] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has subslice power gating: no
<7> [38.325871] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has EU power gating: yes
<6> [38.326008] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [38.326010] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [38.326011] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [38.327451] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [38.328464] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [38.329216] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [38.329286] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [38.342423] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [38.342508] [IGT] i915_module_load: finished subtest load, SUCCESS
<6> [38.342608] [IGT] i915_module_load: exiting, ret=0
Created at 2025-03-12 23:09:31