Hardware List

Results for igt@perf_pmu@rc6@runtime-pm-gt0

Machine description: shard-rkl-3

Result: Pass

git-log-oneline i915_display_info16 igt_runner16 runtimes16 results16.json results16-i915-load.json i915_display_info_post_exec16 boot16 dmesg16

Detail	Value
Duration	9.32 seconds
Hostname	shard-rkl-3
Igt-Version	IGT-Version: 1.30-g0a4beb5fb (x86_64) (Linux: 6.14.0-rc5-CI_DRM_16231-g3ccfd8016ad8+ x86_64)
Out	Starting dynamic subtest: runtime-pm-gt0 Dynamic subtest runtime-pm-gt0: SUCCESS (9.320s)
Err	Starting dynamic subtest: runtime-pm-gt0 Dynamic subtest runtime-pm-gt0: SUCCESS (9.320s)
Dmesg	<6> [537.885241] [IGT] perf_pmu: starting dynamic subtest runtime-pm-gt0 <7> [537.885689] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [537.887029] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe A] <7> [537.887253] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.enable (expected yes, found no) <7> [537.887893] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.active (expected yes, found no) <7> [537.888124] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1) <7> [537.888268] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in lane_count (expected 4, found 0) <7> [537.888427] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in output_types (expected 0x00000040, found 0x00000000) <7> [537.888570] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0) <7> [537.888715] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 1920, found 0) <7> [537.888859] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 2360, found 0) <7> [537.889001] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 1920, found 0) <7> [537.889141] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 2360, found 0) <7> [537.889281] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2008, found 0) <7> [537.889431] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2096, found 0) <7> [537.889575] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1080, found 0) <7> [537.889716] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1080, found 0) <7> [537.889855] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1084, found 0) <7> [537.889993] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1089, found 0) <7> [537.890132] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1125, found 0) <7> [537.890270] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1125, found 0) <7> [537.890420] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 1920, found 0) <7> [537.890566] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 2360, found 0) <7> [537.890705] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 1920, found 0) <7> [537.890844] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 2360, found 0) <7> [537.890983] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2008, found 0) <7> [537.891123] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2096, found 0) <7> [537.891261] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1080, found 0) <7> [537.891412] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1080, found 0) <7> [537.891550] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1084, found 0) <7> [537.891689] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1089, found 0) <7> [537.891828] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1125, found 0) <7> [537.891968] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1125, found 0) <7> [537.892107] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0) <7> [537.892247] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.flags (1) (expected 1, found 0) <7> [537.892411] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.flags (4) (expected 4, found 0) <7> [537.892556] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0) <7> [537.892699] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 139929, found 0) <7> [537.892843] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 139929, found 0) <7> [537.892986] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in port_clock (expected 139929, found 0) <7> [537.893128] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:82:pipe A] fastset requirement not met, forcing full modeset <7> [537.893269] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:82:pipe A] releasing DPLL 0 <7> [537.893448] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x3 -> 0x1 (total dbuf slices 0x3), mbus joined? no->no <7> [537.893592] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:82:pipe A] dbuf slices 0x3 -> 0x0, ddb (0 - 2048) -> (0 - 0), active pipes 0x1 -> 0x0 <7> [537.893767] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] ddb ( 0 - 2016) -> ( 0 - 0), size 2016 -> 0 <7> [537.893907] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:77:cursor A] ddb (2016 - 2048) -> ( 0 - 0), size 32 -> 0 <7> [537.894047] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [537.894186] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] lines 1, 2, 2, 2, 2, 5, 8, 9, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [537.894325] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] blocks 16, 33, 33, 33, 33, 81, 129, 145, 30, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [537.894478] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] min_ddb 19, 38, 38, 38, 38, 91, 143, 161, 31, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [537.894619] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:82:pipe A] data rate 0 num active planes 0 <7> [537.894764] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 16761 required 0 <7> [537.894928] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 180000 kHz, actual 180000 kHz <7> [537.895069] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0 <7> [537.895214] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:82:pipe A] enable: no [modeset] <7> [537.895367] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:32:plane 1A] fb: [NOFB], visible: no <7> [537.895510] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:41:plane 2A] fb: [NOFB], visible: no <7> [537.895650] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:50:plane 3A] fb: [NOFB], visible: no <7> [537.895790] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:59:plane 4A] fb: [NOFB], visible: no <7> [537.895930] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:68:plane 5A] fb: [NOFB], visible: no <7> [537.896069] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:77:cursor A] fb: [NOFB], visible: no <7> [537.899579] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A <7> [537.919191] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_TC1 <7> [537.919361] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:82:pipe A] <7> [537.919527] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0 <7> [537.919680] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:32:plane 1A] <7> [537.919831] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:136:DDI B/PHY B] <7> [537.919974] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:138:DP-MST A] <7> [537.920114] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:139:DP-MST B] <7> [537.920253] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:153:DDI TC1/PHY C] <7> [537.920411] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:157:DDI TC2/PHY D] <7> [537.920555] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:159:DP-MST A] <7> [537.920692] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:160:DP-MST B] <7> [537.920830] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:154:HDMI-A-2] <7> [537.921029] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [537.921219] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3 <7> [537.921395] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:82:pipe A] <7> [537.921739] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:134:pipe B] <7> [537.985471] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [537.986145] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [537.986841] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [537.988620] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [538.922902] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [538.930285] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [538.931667] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [538.932481] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [538.932778] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [538.932928] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [538.933478] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [542.991783] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [542.992141] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [542.992765] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [542.993382] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [542.994073] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [542.994755] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [542.995392] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [542.996078] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [542.996734] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [542.997716] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [542.997866] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [542.998701] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [542.999394] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [542.999550] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [543.005700] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [543.007114] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [543.007270] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:137:DP-1] <7> [543.011845] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1] <7> [543.016719] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:154:HDMI-A-2] <7> [543.062165] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:154:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [543.062176] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:154:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [543.062179] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:154:HDMI-A-2] ELD monitor fitHeadless4k <7> [543.062182] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:154:HDMI-A-2] ELD size 36, SAD count 0 <7> [543.063407] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [543.063553] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [543.064622] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [543.064763] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [543.064784] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:158:DP-2] <7> [543.069510] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:164:HDMI-A-3] <7> [543.075573] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [543.075725] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [543.079193] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [543.080592] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [543.080835] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [543.081114] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [543.081262] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [543.081440] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [545.184640] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [545.184982] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [545.185604] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [545.186473] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [545.187492] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [545.188492] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [545.189231] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [545.189942] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [545.190206] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [545.190722] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [545.190865] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [545.191129] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [545.191846] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [545.192006] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [545.198153] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [545.199467] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [545.199694] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:137:DP-1] <7> [545.204576] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:148:HDMI-A-1] <7> [545.209575] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:154:HDMI-A-2] <7> [545.251318] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:154:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [545.251328] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:154:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [545.251331] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:154:HDMI-A-2] ELD monitor fitHeadless4k <7> [545.251334] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:154:HDMI-A-2] ELD size 36, SAD count 0 <7> [545.253671] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [545.253809] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [545.254881] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [545.255021] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [545.255042] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:158:DP-2] <7> [545.259596] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:164:HDMI-A-3] <6> [547.206227] [IGT] perf_pmu: finished subtest runtime-pm-gt0, SUCCESS

Created at 2025-03-06 07:35:36