Hardware List

Results for igt@i915_pm_rpm@system-suspend-execbuf

Machine description: shard-rkl-1

Result: Pass

integration-manifest git-log-oneline i915_display_info12 igt_runner12 runtimes12 results12.json i915_display_info_post_exec12 boot12 dmesg12

Detail	Value
Duration	22.45 seconds
Hostname	shard-rkl-1
Igt-Version	IGT-Version: 1.30-gedf352a96 (x86_64) (Linux: 6.13.0-rc2-CI_DRM_15843-g3002940575eb+ x86_64)
Out	Using IGT_SRANDOM=1734146830 for randomisation Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: 0000:00:02.0@ffff88811a17b458 has 1/1 users at track_intel_runtime_pm_wakeref+0x92/0xb0 [i915] __intel_runtime_pm_get+0x3c/0xb0 [i915] intel_runtime_pm_get_raw+0x10/0x20 [i915] __intel_display_power_put_async+0x44/0x1e0 [i915] transcoder_ddi_func_is_enabled+0xb2/0xf0 [i915] hsw_get_pipe_config+0x269/0xcf0 [i915] intel_crtc_get_pipe_config+0x24/0x50 [i915] intel_modeset_verify_crtc+0x11a/0x740 [i915] intel_atomic_commit_tail+0xe7b/0x18b0 [i915] intel_atomic_commit+0x2db/0x320 [i915] drm_atomic_commit+0xad/0xf0 drm_atomic_helper_set_config+0x82/0xd0 [drm_kms_helper] drm_mode_setcrtc+0x42c/0xa50 drm_ioctl_kernel+0xb9/0x120 drm_ioctl+0x2f9/0x5b0 __x64_sys_ioctl+0xa4/0xe0 Starting subtest: system-suspend-execbuf [cmd] rtcwake: assuming RTC uses UTC ... [cmd] rtcwake: wakeup from "mem" using /dev/rtc0 at Sat Dec 14 03:27:28 2024 Subtest system-suspend-execbuf: SUCCESS (22.449s)
Err	Starting subtest: system-suspend-execbuf Subtest system-suspend-execbuf: SUCCESS (22.449s)
Dmesg	<6> [344.868485] Console: switching to colour dummy device 80x25 <6> [344.868875] [IGT] i915_pm_rpm: executing <7> [344.870143] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [344.870617] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:137:HDMI-A-1] <7> [344.870634] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [344.874879] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:137:HDMI-A-1] disconnected <7> [344.874937] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:147:HDMI-A-2] <7> [344.874950] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [344.901626] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [344.901644] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [344.901650] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [344.901656] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [344.901942] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [344.902241] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [344.902721] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [344.903015] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [344.903701] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1366x768": 216 268000 1366 1414 1446 1526 768 771 777 814 0x40 0x6 (CLOCK_HIGH) <7> [344.903714] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080i": 60 74250 1920 2008 2052 2200 1080 1084 1094 1125 0x40 0x15 (NO_INTERLACE) <7> [344.903724] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080i": 60 74176 1920 2008 2052 2200 1080 1084 1094 1125 0x40 0x15 (NO_INTERLACE) <7> [344.903734] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:147:HDMI-A-2] probed modes: <7> [344.903753] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1920x1080": 53 139930 1920 2008 2096 2360 1080 1084 1089 1125 0x48 0x5 <7> [344.903770] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "4088x2304": 10 108000 4088 4152 4280 4536 2304 2305 2308 2340 0x40 0x5 <7> [344.903786] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "3840x2160": 15 128430 3840 3889 3921 4000 2160 2163 2169 2195 0x40 0xa <7> [344.903800] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "2880x1800": 11 60000 2880 2888 2984 3040 1800 1802 1820 1845 0x40 0xa <7> [344.903815] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "2560x1600": 13 60000 2560 2568 2664 2720 1600 1602 1620 1645 0x40 0xa <7> [344.903846] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "2560x1440": 15 60000 2560 2568 2664 2720 1440 1442 1460 1485 0x40 0xa <7> [344.903861] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "2048x1536": 17 60000 2048 2056 2152 2208 1536 1538 1556 1581 0x40 0xa <7> [344.903875] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1600x1200": 60 162000 1600 1664 1856 2160 1200 1201 1204 1250 0x40 0x5 <7> [344.903890] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1680x1050": 60 146250 1680 1784 1960 2240 1050 1053 1059 1089 0x40 0x6 <7> [344.903904] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5 <7> [344.903919] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1280x1024": 75 135000 1280 1296 1440 1688 1024 1025 1028 1066 0x40 0x5 <7> [344.903933] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1360x768": 60 84963 1366 1431 1567 1776 768 771 781 798 0x0 0x6 <7> [344.903948] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1360x768": 20 25190 1360 1368 1464 1520 768 770 788 813 0x40 0xa <7> [344.903962] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1280x800": 60 83500 1280 1352 1480 1680 800 803 809 831 0x40 0x6 <7> [344.903976] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1152x864": 75 108000 1152 1216 1344 1600 864 865 868 900 0x40 0x5 <7> [344.903990] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 <7> [344.904004] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 <7> [344.904018] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1280x720": 60 74176 1280 1390 1430 1650 720 725 730 750 0x40 0x5 <7> [344.904031] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1024x768": 75 78750 1024 1040 1136 1312 768 769 772 800 0x40 0x5 <7> [344.904045] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa <7> [344.904059] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1440x480": 60 54054 1440 1472 1596 1716 480 489 495 525 0x40 0xa <7> [344.904072] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1440x480": 60 54000 1440 1472 1596 1716 480 489 495 525 0x40 0xa <7> [344.904086] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1024x576": 60 46560 1024 1064 1160 1296 576 579 584 599 0x0 0x6 <7> [344.904100] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "832x624": 75 57284 832 864 928 1152 624 625 628 667 0x40 0xa <7> [344.904114] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "800x600": 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5 <7> [344.904127] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5 <7> [344.904141] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "640x480": 75 31500 640 656 720 840 480 481 484 500 0x40 0xa <7> [344.904155] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "640x480": 60 25200 640 656 752 800 480 490 492 525 0x40 0xa <7> [344.904169] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa <7> [344.904182] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa <7> [344.904196] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "720x400": 70 28320 720 738 846 900 400 412 414 449 0x40 0x6 <7> [344.904305] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:151:DP-1] <7> [344.904321] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [344.908853] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:151:DP-1] disconnected <7> [344.908916] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:158:HDMI-A-3] <7> [344.908929] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [344.913887] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:158:HDMI-A-3] disconnected <7> [344.917369] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:137:HDMI-A-1] <7> [344.917384] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [344.921864] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:137:HDMI-A-1] disconnected <7> [344.922286] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:151:DP-1] <7> [344.922296] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [344.926861] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:151:DP-1] disconnected <7> [344.927131] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:158:HDMI-A-3] <7> [344.927141] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [344.931873] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:158:HDMI-A-3] disconnected <7> [344.932150] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:137:HDMI-A-1] <7> [344.932160] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [344.936872] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:137:HDMI-A-1] disconnected <7> [344.936893] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:147:HDMI-A-2] <7> [344.936903] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [344.963095] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [344.963110] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [344.963115] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [344.963120] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [344.963355] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [344.963614] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [344.964084] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [344.964344] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [344.965012] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1366x768": 216 268000 1366 1414 1446 1526 768 771 777 814 0x40 0x6 (CLOCK_HIGH) <7> [344.965023] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080i": 60 74250 1920 2008 2052 2200 1080 1084 1094 1125 0x40 0x15 (NO_INTERLACE) <7> [344.965030] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080i": 60 74176 1920 2008 2052 2200 1080 1084 1094 1125 0x40 0x15 (NO_INTERLACE) <7> [344.965039] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:147:HDMI-A-2] probed modes: <7> [344.965054] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1920x1080": 53 139930 1920 2008 2096 2360 1080 1084 1089 1125 0x48 0x5 <7> [344.965068] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "4088x2304": 10 108000 4088 4152 4280 4536 2304 2305 2308 2340 0x40 0x5 <7> [344.965081] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "3840x2160": 15 128430 3840 3889 3921 4000 2160 2163 2169 2195 0x40 0xa <7> [344.965094] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "2880x1800": 11 60000 2880 2888 2984 3040 1800 1802 1820 1845 0x40 0xa <7> [344.965108] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "2560x1600": 13 60000 2560 2568 2664 2720 1600 1602 1620 1645 0x40 0xa <7> [344.965121] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "2560x1440": 15 60000 2560 2568 2664 2720 1440 1442 1460 1485 0x40 0xa <7> [344.965133] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "2048x1536": 17 60000 2048 2056 2152 2208 1536 1538 1556 1581 0x40 0xa <7> [344.965146] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1600x1200": 60 162000 1600 1664 1856 2160 1200 1201 1204 1250 0x40 0x5 <7> [344.965159] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1680x1050": 60 146250 1680 1784 1960 2240 1050 1053 1059 1089 0x40 0x6 <7> [344.965171] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5 <7> [344.965185] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1280x1024": 75 135000 1280 1296 1440 1688 1024 1025 1028 1066 0x40 0x5 <7> [344.965197] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1360x768": 60 84963 1366 1431 1567 1776 768 771 781 798 0x0 0x6 <7> [344.965210] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1360x768": 20 25190 1360 1368 1464 1520 768 770 788 813 0x40 0xa <7> [344.965222] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1280x800": 60 83500 1280 1352 1480 1680 800 803 809 831 0x40 0x6 <7> [344.965234] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1152x864": 75 108000 1152 1216 1344 1600 864 865 868 900 0x40 0x5 <7> [344.965246] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 <7> [344.965259] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 <7> [344.965271] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1280x720": 60 74176 1280 1390 1430 1650 720 725 730 750 0x40 0x5 <7> [344.965283] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1024x768": 75 78750 1024 1040 1136 1312 768 769 772 800 0x40 0x5 <7> [344.965295] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa <7> [344.965307] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1440x480": 60 54054 1440 1472 1596 1716 480 489 495 525 0x40 0xa <7> [344.965319] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1440x480": 60 54000 1440 1472 1596 1716 480 489 495 525 0x40 0xa <7> [344.965331] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "1024x576": 60 46560 1024 1064 1160 1296 576 579 584 599 0x0 0x6 <7> [344.965344] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "832x624": 75 57284 832 864 928 1152 624 625 628 667 0x40 0xa <7> [344.965356] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "800x600": 75 49500 800 816 896 1056 600 601 604 625 0x40 0x5 <7> [344.965368] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5 <7> [344.965380] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "640x480": 75 31500 640 656 720 840 480 481 484 500 0x40 0xa <7> [344.965393] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "640x480": 60 25200 640 656 752 800 480 490 492 525 0x40 0xa <7> [344.965405] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa <7> [344.965417] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa <7> [344.965429] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] Probed mode: "720x400": 70 28320 720 738 846 900 400 412 414 449 0x40 0x6 <7> [344.965479] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:151:DP-1] <7> [344.965492] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [344.969842] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:151:DP-1] disconnected <7> [344.969870] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:158:HDMI-A-3] <7> [344.969882] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [344.974846] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:158:HDMI-A-3] disconnected <7> [344.975220] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:163] <7> [345.991181] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe A] <7> [345.991397] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.enable (expected yes, found no) <7> [345.992129] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.active (expected yes, found no) <7> [345.992777] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1) <7> [345.993448] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in lane_count (expected 4, found 0) <7> [345.994099] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in output_types (expected 0x00000040, found 0x00000000) <7> [345.994729] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0) <7> [345.995414] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 1920, found 0) <7> [345.995883] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 2360, found 0) <7> [345.996051] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 1920, found 0) <7> [345.996217] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 2360, found 0) <7> [345.996381] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 2008, found 0) <7> [345.996545] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2096, found 0) <7> [345.996707] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1080, found 0) <7> [345.996877] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1080, found 0) <7> [345.997040] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1084, found 0) <7> [345.997202] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1089, found 0) <7> [345.997372] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1125, found 0) <7> [345.997539] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1125, found 0) <7> [345.997704] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 1920, found 0) <7> [345.997874] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 2360, found 0) <7> [345.998038] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 1920, found 0) <7> [345.998201] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 2360, found 0) <7> [345.998364] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 2008, found 0) <7> [345.998527] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2096, found 0) <7> [345.998691] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1080, found 0) <7> [345.998858] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1080, found 0) <7> [345.999024] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1084, found 0) <7> [345.999194] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1089, found 0) <7> [345.999360] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1125, found 0) <7> [345.999525] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1125, found 0) <7> [345.999689] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0) <7> [345.999857] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.flags (1) (expected 1, found 0) <7> [346.000020] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.flags (4) (expected 4, found 0) <7> [346.000184] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0) <7> [346.000347] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 139929, found 0) <7> [346.000510] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 139929, found 0) <7> [346.000671] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in port_clock (expected 139929, found 0) <7> [346.000840] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:82:pipe A] fastset requirement not met, forcing full modeset <7> [346.001003] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:82:pipe A] releasing DPLL 0 <7> [346.001215] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x3 -> 0x1 (total dbuf slices 0x3), mbus joined? no->no <7> [346.001384] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:82:pipe A] dbuf slices 0x3 -> 0x0, ddb (0 - 2048) -> (0 - 0), active pipes 0x1 -> 0x0 <7> [346.001580] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] ddb ( 0 - 2016) -> ( 0 - 0), size 2016 -> 0 <7> [346.001742] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:77:cursor A] ddb (2016 - 2048) -> ( 0 - 0), size 32 -> 0 <7> [346.001924] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [346.002084] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] lines 1, 2, 2, 2, 2, 5, 8, 9, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [346.002245] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] blocks 16, 33, 33, 33, 33, 81, 129, 145, 30, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [346.002403] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] min_ddb 19, 38, 38, 38, 38, 91, 143, 161, 31, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [346.002564] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:82:pipe A] data rate 0 num active planes 0 <7> [346.002736] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 16761 required 0 <7> [346.002937] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 180000 kHz, actual 180000 kHz <7> [346.003102] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0 <7> [346.003269] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:82:pipe A] enable: no [modeset] <7> [346.003435] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:32:plane 1A] fb: [NOFB], visible: no <7> [346.003598] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:41:plane 2A] fb: [NOFB], visible: no <7> [346.003760] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:50:plane 3A] fb: [NOFB], visible: no <7> [346.003934] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:59:plane 4A] fb: [NOFB], visible: no <7> [346.004096] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:68:plane 5A] fb: [NOFB], visible: no <7> [346.004257] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:77:cursor A] fb: [NOFB], visible: no <7> [346.016869] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A <7> [346.036423] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_TC1 <7> [346.037134] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:82:pipe A] <7> [346.037839] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0 <7> [346.038495] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:32:plane 1A] <7> [346.039155] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:136:DDI B/PHY B] <7> [346.039771] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:146:DDI TC1/PHY C] <7> [346.040446] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:150:DDI TC2/PHY D] <7> [346.041084] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:152:DP-MST A] <7> [346.041710] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:153:DP-MST B] <7> [346.042350] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:147:HDMI-A-2] <7> [346.043144] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [346.043880] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3 <7> [346.044575] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:82:pipe A] <7> [346.045710] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:134:pipe B] <7> [346.145935] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [346.146696] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [346.147513] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [346.149711] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [346.150941] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [346.154791] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [346.156146] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [346.156475] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [346.156775] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [346.156957] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [346.157222] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <6> [346.250436] [IGT] i915_pm_rpm: starting subtest system-suspend-execbuf <7> [346.251015] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe A] <7> [346.262879] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [346.263340] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [346.264013] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [346.264696] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [346.265517] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [346.266290] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [346.267037] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [346.267765] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [346.268494] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [346.270864] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [346.271517] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [346.273657] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [346.275748] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [346.276415] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [346.285489] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [346.285712] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [346.286017] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [346.286793] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [346.288199] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [346.288459] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:134:pipe B] <7> [346.293050] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [346.305803] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [346.306044] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [346.306251] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [346.329797] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [346.329807] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [346.329810] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [346.329814] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [346.330996] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [346.331154] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [346.332213] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [346.332373] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [346.332471] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [346.333405] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [346.334817] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [346.339803] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [346.352800] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [346.352991] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [346.353173] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [346.354488] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [346.354701] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [346.358213] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [346.359575] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [346.359949] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [346.360346] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [346.360605] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [346.360925] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <6> [346.530037] PM: suspend entry (s2idle) <6> [346.530691] Filesystems sync: 0.000 seconds <6> [346.544738] Freezing user space processes <6> [346.546906] Freezing user space processes completed (elapsed 0.002 seconds) <6> [346.546921] OOM killer disabled. <6> [346.546926] Freezing remaining freezable tasks <6> [346.548561] Freezing remaining freezable tasks completed (elapsed 0.001 seconds) <7> [346.578086] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [346.578585] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [346.579299] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [346.580036] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [346.580809] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [346.581565] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [346.582319] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [346.583069] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [346.583812] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [346.584824] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [346.585481] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [346.586847] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [346.588934] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [346.589572] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [346.599831] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [346.599984] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [346.600185] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [346.604821] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <6> [346.616236] smsc75xx 1-1:1.0 enx803f5d0909b4: entering SUSPEND2 mode <7> [346.633350] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [346.637786] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [346.639304] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [346.639653] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010 <6> [346.644983] e1000e: EEE TX LPI TIMER: 00000011 <7> [346.646269] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [346.646281] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [346.646284] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [346.646287] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [346.646501] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [346.646663] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [346.647023] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [346.647188] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [346.647210] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [346.651793] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [346.651790] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3 <7> [346.652007] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [346.652185] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [346.652355] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [346.654905] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [346.656113] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [346.657538] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [346.657942] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4 <7> [346.659128] i915 0000:00:02.0: [drm:i915_hdcp_component_unbind [i915]] I915 HDCP comp unbind <7> [346.781860] PM: suspend of devices complete after 169.616 msecs <7> [346.781865] PM: start suspend of devices complete after 233.299 msecs <7> [346.793805] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4 <7> [346.794081] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3 <7> [346.794256] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [346.794429] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [346.794596] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [346.795907] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [346.797131] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [346.798519] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [346.798947] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [346.799313] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [346.799547] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [346.812008] PM: late suspend of devices complete after 30.141 msecs <6> [346.824894] ACPI: EC: interrupt blocked <7> [347.027735] PM: noirq suspend of devices complete after 213.121 msecs <6> [347.027760] ACPI: \_SB_.PR00: LPI: Device not power manageable <6> [347.027782] ACPI: \_SB_.PR01: LPI: Device not power manageable <6> [347.027790] ACPI: \_SB_.PR02: LPI: Device not power manageable <6> [347.027797] ACPI: \_SB_.PR03: LPI: Device not power manageable <6> [347.027804] ACPI: \_SB_.PR04: LPI: Device not power manageable <6> [347.027810] ACPI: \_SB_.PR05: LPI: Device not power manageable <6> [347.027816] ACPI: \_SB_.PR06: LPI: Device not power manageable <6> [347.027822] ACPI: \_SB_.PR07: LPI: Device not power manageable <6> [347.027828] ACPI: \_SB_.PC00.GFX0: LPI: Device not power manageable <6> [347.027834] ACPI: \_SB_.PC00.I2C0: LPI: Constraint not met; min power state:D3hot current power state:D0 <6> [347.027841] ACPI: \_SB_.PC00.I2C1: LPI: Constraint not met; min power state:D3hot current power state:D0 <6> [347.027848] ACPI: \_SB_.PC00.I2C2: LPI: Constraint not met; min power state:D3hot current power state:D0 <6> [347.027854] ACPI: \_SB_.PC00.I2C3: LPI: Constraint not met; min power state:D3hot current power state:D0 <6> [347.027859] ACPI: \_SB_.PC00.I2C4: LPI: Constraint not met; min power state:D3hot current power state:D0 <6> [347.027865] ACPI: \_SB_.PC00.I2C5: LPI: Constraint not met; min power state:D3hot current power state:D0 <6> [347.027871] ACPI: \_SB_.PR08: LPI: Device not power manageable <6> [347.027877] ACPI: \_SB_.PR09: LPI: Device not power manageable <6> [347.027883] ACPI: \_SB_.PR10: LPI: Device not power manageable <6> [347.027889] ACPI: \_SB_.PR11: LPI: Device not power manageable <6> [347.027895] ACPI: \_SB_.PC00.HECI: LPI: Device not power manageable <6> [347.027901] ACPI: \_SB_.PC00.GNA0: LPI: Device not power manageable <6> [347.031200] ACPI: \_SB_.PEPD: Successfully transitioned to state screen off <7> [347.284350] PM: Triggering wakeup from IRQ 9 <6> [347.288801] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 entry <7> [347.288808] PM: suspend-to-idle <7> [347.288961] ACPI: EC: ACPI EC GPE status set <7> [347.288991] ACPI: PM: Rearming ACPI SCI for wakeup <7> [362.447411] PM: Triggering wakeup from IRQ 9 <7> [362.447642] ACPI: PM: ACPI fixed event wakeup <7> [362.447645] PM: resume from suspend-to-idle <6> [362.601512] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 exit <6> [362.604731] ACPI: \_SB_.PEPD: Successfully transitioned to state screen on <6> [362.605352] ACPI: EC: interrupt unblocked <7> [362.950329] PM: noirq resume of devices complete after 345.600 msecs <7> [362.955375] i915 0000:00:02.0: [drm:gen9_sanitize_dc_state [i915]] Resetting DC state tracking from 08 to 08 <7> [362.956025] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [362.956654] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [362.957329] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [362.958051] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [362.958767] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [362.958998] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [362.959226] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [362.959444] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [362.960192] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [362.960370] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [362.961057] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [362.961784] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [362.961950] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [362.962115] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [362.962444] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [362.962633] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4 <7> [362.962885] PM: early resume of devices complete after 9.916 msecs <7> [362.967945] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 180000 kHz, VCO 720000 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [362.968273] i915 0000:00:02.0: [drm:nop_init_clock_gating [i915]] No clock gating settings or workarounds applied. <7> [362.968781] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:82:pipe A] hw state readout: disabled <7> [362.969175] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:134:pipe B] hw state readout: disabled <7> [362.969506] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:32:plane 1A] hw state readout: disabled, pipe A <7> [362.969808] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:41:plane 2A] hw state readout: disabled, pipe A <7> [362.970106] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:50:plane 3A] hw state readout: disabled, pipe A <7> [362.970420] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:59:plane 4A] hw state readout: disabled, pipe A <7> [362.970739] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:plane 5A] hw state readout: disabled, pipe A <7> [362.971116] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:77:cursor A] hw state readout: disabled, pipe A <7> [362.971506] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:84:plane 1B] hw state readout: disabled, pipe B <7> [362.971900] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:93:plane 2B] hw state readout: disabled, pipe B <7> [362.972189] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:102:plane 3B] hw state readout: disabled, pipe B <7> [362.972508] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:111:plane 4B] hw state readout: disabled, pipe B <7> [362.972798] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:120:plane 5B] hw state readout: disabled, pipe B <7> [362.973096] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:129:cursor B] hw state readout: disabled, pipe B <7> [362.973391] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:136:DDI B/PHY B] hw state readout: disabled, pipe A <7> [362.973675] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:146:DDI TC1/PHY C] hw state readout: disabled, pipe A <7> [362.973958] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:150:DDI TC2/PHY D] hw state readout: disabled, pipe A <7> [362.974235] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:152:DP-MST A] hw state readout: disabled, pipe A <7> [362.974524] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:153:DP-MST B] hw state readout: disabled, pipe B <7> [362.974815] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0 <7> [362.975087] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [362.975307] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0 <7> [362.975549] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:137:HDMI-A-1] hw state readout: disabled <7> [362.975777] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:147:HDMI-A-2] hw state readout: disabled <7> [362.976003] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:151:DP-1] hw state readout: disabled <7> [362.976227] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:158:HDMI-A-3] hw state readout: disabled <7> [362.976438] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:32:plane 1A] min_cdclk 0 kHz <7> [362.976639] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:41:plane 2A] min_cdclk 0 kHz <7> [362.976840] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:50:plane 3A] min_cdclk 0 kHz <7> [362.977049] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:59:plane 4A] min_cdclk 0 kHz <7> [362.977257] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:plane 5A] min_cdclk 0 kHz <7> [362.977469] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:77:cursor A] min_cdclk 0 kHz <7> [362.977673] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0 <7> [362.977877] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:84:plane 1B] min_cdclk 0 kHz <7> [362.978048] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:93:plane 2B] min_cdclk 0 kHz <7> [362.978225] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:102:plane 3B] min_cdclk 0 kHz <7> [362.978407] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:111:plane 4B] min_cdclk 0 kHz <7> [362.978580] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:120:plane 5B] min_cdclk 0 kHz <7> [362.978752] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:129:cursor B] min_cdclk 0 kHz <7> [362.978924] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0 <7> [362.979131] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:82:pipe A] enable: no [setup_hw_state] <7> [362.979310] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:134:pipe B] enable: no [setup_hw_state] <7> [362.979497] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:82:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [362.979668] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:134:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [362.979894] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in dpll_hw_state <7> [362.980079] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] expected: <7> [362.980261] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] dpll_hw_state: cfgcr0: 0x0, cfgcr1: 0x0, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [362.980449] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] found: <6> [362.980597] serial 00:03: activated <7> [362.980627] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] dpll_hw_state: cfgcr0: 0x1a6655d, cfgcr1: 0xe84, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [362.980806] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:82:pipe A] fastset requirement not met, forcing full modeset <7> [362.980992] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:134:pipe B] fastset requirement not met in dpll_hw_state <7> [362.981155] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] expected: <7> [362.981318] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] dpll_hw_state: cfgcr0: 0x0, cfgcr1: 0x0, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [362.981503] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] found: <7> [362.981665] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] dpll_hw_state: cfgcr0: 0x1a6655d, cfgcr1: 0xe84, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [362.981829] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:134:pipe B] fastset requirement not met, forcing full modeset <7> [362.982021] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 16761 required 0 <7> [362.982205] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:82:pipe A] enable: no [modeset] <7> [362.982374] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:32:plane 1A] fb: [NOFB], visible: no <7> [362.982545] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:41:plane 2A] fb: [NOFB], visible: no <7> [362.982712] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:50:plane 3A] fb: [NOFB], visible: no <7> [362.982876] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:59:plane 4A] fb: [NOFB], visible: no <7> [362.983039] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:68:plane 5A] fb: [NOFB], visible: no <7> [362.983201] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:77:cursor A] fb: [NOFB], visible: no <7> [362.983368] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:134:pipe B] enable: no [modeset] <7> [362.983531] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:84:plane 1B] fb: [NOFB], visible: no <7> [362.983692] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:93:plane 2B] fb: [NOFB], visible: no <7> [362.983853] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:102:plane 3B] fb: [NOFB], visible: no <7> [362.984014] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:111:plane 4B] fb: [NOFB], visible: no <7> [362.984175] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:120:plane 5B] fb: [NOFB], visible: no <7> [362.984337] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:129:cursor B] fb: [NOFB], visible: no <7> [362.984562] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:136:DDI B/PHY B] <7> [362.984727] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:146:DDI TC1/PHY C] <7> [362.984891] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:150:DDI TC2/PHY D] <7> [362.985052] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:152:DP-MST A] <7> [362.985212] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:153:DP-MST B] <7> [362.985379] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:137:HDMI-A-1] <7> [362.985565] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:147:HDMI-A-2] <7> [362.985747] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:151:DP-1] <7> [362.985927] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:158:HDMI-A-3] <7> [362.986152] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:82:pipe A] <7> [362.986394] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:134:pipe B] <7> [362.986885] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected <7> [362.987060] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <6> [362.987204] nvme nvme0: 12/0/0 default/read/poll queues <7> [362.991470] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [362.991793] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4 <7> [362.992115] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010 <7> [363.018542] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [363.018553] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [363.018556] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [363.018559] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [363.018873] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [363.019034] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [363.019476] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [363.019637] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [363.019658] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [363.024379] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <6> [363.026633] smsc75xx 1-1:1.0 enx803f5d0909b4: resuming from SUSPEND2 <7> [363.073389] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3 <7> [363.073690] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [363.073866] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [363.074033] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [363.075341] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <6> [363.270867] ata3: SATA link down (SStatus 4 SControl 300) <6> [363.278894] ata2: SATA link down (SStatus 4 SControl 300) <6> [363.278946] ata4: SATA link down (SStatus 4 SControl 300) <3> [363.665349] atkbd serio0: Failed to enable keyboard on isa0060/serio0 <7> [363.965249] PM: resume of devices complete after 1002.385 msecs <6> [363.968305] OOM killer enabled. <6> [363.968313] Restarting tasks ... <7> [363.968986] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind <4> [363.969558] done. <5> [363.969588] random: crng reseeded on system resumption <6> [363.969638] PM: suspend exit <7> [363.969594] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <6> [363.969718] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915]) <6> [363.973791] mei_pxp 0000:00:16.0-fbf6fcf1-96cf-4e2e-a6a6-1bab8cbe36b1: bound 0000:00:02.0 (ops i915_pxp_tee_component_ops [i915]) <7> [363.976831] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [363.978249] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [363.979009] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [363.979312] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [363.979525] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [363.979729] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [364.090629] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [364.091117] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [364.091819] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [364.092534] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [364.093289] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.094073] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.094821] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.095570] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.096267] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [364.097812] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [364.098454] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [364.099225] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [364.101344] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [364.102002] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [364.114827] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [364.115044] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [364.115219] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [364.120985] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [364.166352] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [364.166362] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [364.166366] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [364.166369] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [364.166570] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [364.166724] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [364.167062] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [364.167224] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [364.167245] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [364.172946] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [364.225405] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [364.227129] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [364.231954] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [364.233484] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [364.234266] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [364.235111] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [364.235711] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [364.236351] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [364.328424] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [364.328899] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [364.329598] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [364.330379] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [364.331164] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.331956] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.332792] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.333553] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.333911] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [364.334549] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [364.334736] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [364.335482] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [364.336191] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [364.336369] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [364.341425] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [364.341556] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [364.341889] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [364.346374] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [364.391677] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [364.391687] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [364.391691] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [364.391694] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [364.391895] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [364.392054] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [364.392985] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [364.393163] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [364.393184] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [364.399122] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [364.449396] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [364.450111] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [364.454956] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [364.456476] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [364.457251] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [364.458078] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [364.458730] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [364.459420] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [364.553409] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [364.553876] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [364.554576] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [364.555359] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [364.556146] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.556936] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.557739] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.558517] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.559266] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [364.559885] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [364.560052] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [364.560343] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [364.561058] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [364.561226] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [364.568648] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [364.568858] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [364.569356] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [364.575186] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [364.620423] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [364.620433] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [364.620436] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [364.620440] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [364.621615] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [364.621788] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [364.622123] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [364.622285] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [364.622304] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [364.628007] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [364.681385] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [364.682125] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [364.686960] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [364.688308] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [364.688581] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [364.688880] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [364.689049] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [364.689249] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [364.781396] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [364.781852] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [364.782543] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [364.783293] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [364.784080] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.784917] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.785694] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.786461] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [364.787216] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [364.787998] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [364.788708] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [364.789557] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [364.791664] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [364.792339] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [364.802777] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [364.803005] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [364.803365] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [364.809305] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [364.854695] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [364.854704] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [364.854708] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [364.854711] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [364.855894] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [364.856068] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [364.857117] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [364.857279] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [364.857298] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [364.863227] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [364.913373] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [364.914091] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [364.918896] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [364.920239] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [364.920505] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [364.920804] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [364.920976] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [364.921182] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [365.015392] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [365.015856] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [365.016552] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [365.017340] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [365.018126] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.018918] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.019756] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.020569] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.021266] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [365.022077] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [365.022814] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [365.023718] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [365.025825] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [365.026494] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [365.036851] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [365.037078] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [365.037418] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [365.043370] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [365.089854] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [365.089863] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [365.089867] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [365.089870] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [365.091096] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [365.091280] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [365.092379] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [365.092540] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [365.092561] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [365.098390] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [365.145378] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [365.146081] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [365.152119] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [365.153686] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [365.154474] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [365.155274] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [365.155941] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [365.156664] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [365.250386] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [365.250850] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [365.251542] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [365.252230] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [365.252998] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.253763] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.254508] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.255230] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.255968] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [365.256716] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [365.256905] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [365.257184] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [365.257903] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [365.258070] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [365.264257] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [365.264478] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [365.264741] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [365.269365] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [365.314607] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [365.314617] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [365.314620] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [365.314623] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [365.314826] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [365.314982] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [365.315344] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [365.315503] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [365.315522] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [365.321208] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [365.377376] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [365.378117] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [365.384108] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [365.385517] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [365.385803] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [365.386101] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [365.386309] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [365.386578] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [365.478030] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [365.478536] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [365.479201] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [365.479928] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [365.480704] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.481477] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.482398] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.483153] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.483799] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [365.484114] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [365.484295] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [365.484593] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [365.485319] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [365.485494] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [365.490542] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [365.490675] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [365.491002] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [365.495498] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [365.539741] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [365.539750] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [365.539754] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [365.539757] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [365.542098] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [365.542292] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [365.543308] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [365.543476] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [365.543496] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [365.549414] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [365.601367] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [365.602102] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [365.606920] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [365.608268] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [365.608541] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [365.608842] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [365.609011] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [365.609212] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [365.703384] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [365.703844] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [365.704541] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [365.705233] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [365.705993] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.706947] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.707751] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.708508] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.709256] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [365.709971] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [365.710135] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [365.710443] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [365.711176] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [365.711361] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [365.721234] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [365.721492] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [365.721787] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [365.726346] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [365.771689] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [365.771698] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [365.771702] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [365.771705] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [365.772889] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [365.773049] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [365.773391] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [365.773550] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [365.773569] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [365.779254] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [365.833348] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [365.834059] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [365.838888] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [365.840207] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [365.840481] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [365.840798] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [365.840968] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [365.841168] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [365.937370] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [365.937831] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [365.938504] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [365.939186] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [365.939939] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.940697] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.941441] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.942182] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [365.942910] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [365.943656] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [365.944305] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [365.945090] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [365.947165] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [365.947818] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [365.956975] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [365.957258] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [365.957669] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [365.962364] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [366.007677] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [366.007687] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [366.007690] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [366.007693] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [366.008901] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [366.009056] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [366.009397] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [366.009559] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [366.009579] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [366.015269] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [366.065349] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [366.066074] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [366.070921] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [366.072464] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [366.073252] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [366.074119] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [366.074830] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [366.075537] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [366.172374] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [366.172841] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [366.173553] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [366.174245] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [366.175031] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.175789] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.176540] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.177262] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.178025] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [366.178869] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [366.179580] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [366.180448] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [366.182913] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [366.183838] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [366.195481] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [366.195926] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [366.196271] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [366.202175] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [366.247556] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [366.247566] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [366.247569] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [366.247573] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [366.248771] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [366.248997] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [366.250022] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [366.250255] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [366.250306] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [366.256145] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [366.305373] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [366.306086] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [366.310903] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [366.312246] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [366.312519] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [366.312816] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [366.312984] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [366.313184] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [366.408358] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [366.408819] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [366.409514] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [366.410203] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [366.410966] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.411727] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.412463] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.413184] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.413905] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [366.414663] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [366.415329] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [366.416126] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [366.418180] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [366.418826] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [366.427978] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [366.428267] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [366.428694] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [366.433396] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [366.478707] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [366.478716] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [366.478719] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [366.478722] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [366.479908] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [366.480064] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [366.481118] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [366.481282] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [366.481301] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [366.487237] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [366.537348] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [366.538055] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [366.542901] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [366.544221] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [366.544493] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [366.544792] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [366.544961] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [366.545160] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [366.642045] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [366.642535] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [366.643191] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [366.643910] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [366.644662] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.645413] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.646130] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.646882] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.647592] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [366.648330] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [366.648984] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [366.649811] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [366.651890] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [366.652542] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [366.661669] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [366.661948] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [366.662320] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [366.668201] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [366.713547] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [366.713556] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [366.713559] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [366.713562] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [366.713760] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [366.713916] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [366.714256] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [366.714430] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [366.714449] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [366.720139] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [366.769342] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [366.770077] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [366.776061] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [366.777471] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [366.777746] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [366.778050] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [366.778239] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [366.778465] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [366.874348] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [366.874807] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [366.875495] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [366.876183] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [366.876941] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.877876] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.878685] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.879447] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [366.880320] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [366.881110] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [366.881783] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [366.882653] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [366.884243] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [366.884436] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [366.894285] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [366.894518] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [366.895024] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [366.899545] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [366.944892] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [366.944901] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [366.944904] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [366.944908] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [366.946099] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [366.946269] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [366.947314] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [366.947492] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [366.947511] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [366.953449] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [367.001334] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [367.002059] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [367.008044] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [367.009569] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [367.010371] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [367.011163] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [367.011859] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [367.012434] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [367.107349] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [367.107801] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [367.108467] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [367.109143] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [367.109898] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.110653] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.111420] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.112151] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.112889] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [367.113641] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [367.114293] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [367.115084] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [367.117168] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [367.117822] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [367.126960] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [367.127244] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [367.127673] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [367.132381] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [367.177734] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [367.177743] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [367.177747] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [367.177750] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [367.177948] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [367.178108] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [367.179075] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [367.179313] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [367.179347] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [367.185186] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [367.241331] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [367.242037] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [367.246855] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [367.248193] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [367.248458] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [367.248757] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [367.248925] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [367.249125] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [367.341335] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [367.341805] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [367.342522] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [367.343279] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [367.344059] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.344872] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.345643] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.346431] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.346956] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [367.347232] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [367.347422] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [367.347708] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [367.348433] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [367.348598] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [367.353645] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [367.353774] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [367.354080] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [367.358558] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [367.403897] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [367.403906] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [367.403910] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [367.403913] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [367.405101] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [367.405278] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [367.405627] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [367.405787] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [367.405806] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [367.410271] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [367.465317] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [367.466048] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [367.472026] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [367.473551] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [367.474361] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [367.475179] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [367.475864] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [367.476568] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [367.566330] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [367.566792] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [367.567495] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [367.568221] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [367.569122] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.570025] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.570787] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.571542] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.572240] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [367.573030] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [367.573699] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [367.574513] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [367.576622] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [367.577288] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [367.586397] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [367.586722] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [367.587088] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [367.592918] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [367.638316] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [367.638330] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [367.638334] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [367.638337] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [367.639507] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [367.639700] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [367.640036] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [367.640196] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [367.640219] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [367.645904] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [367.697309] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [367.698053] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [367.702885] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [367.704217] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [367.704488] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [367.704786] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [367.704953] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [367.705152] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [367.800122] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [367.800642] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [367.801337] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [367.802042] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [367.802806] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.803752] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.804540] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.805302] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [367.805912] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [367.806204] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [367.806385] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [367.806660] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [367.807384] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [367.807551] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [367.812593] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [367.812723] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [367.813066] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [367.817550] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [367.862873] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [367.862883] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [367.862887] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [367.862890] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [367.864070] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [367.864230] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [367.865300] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [367.865460] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [367.865480] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [367.870282] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [367.921315] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [367.922026] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [367.926863] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [367.928417] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [367.929210] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [367.930049] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [367.930706] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [367.931420] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [368.025326] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [368.025783] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [368.026465] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [368.027153] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [368.027911] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.028677] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.029420] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.030166] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.030909] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [368.031660] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [368.031908] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [368.032183] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [368.032905] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [368.033071] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [368.041709] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [368.041965] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [368.042343] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [368.048213] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [368.092430] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [368.092439] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [368.092442] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [368.092445] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [368.094791] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [368.094953] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [368.095294] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [368.095455] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [368.095475] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [368.101162] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [368.153308] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [368.154043] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [368.160022] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [368.161562] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [368.162374] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [368.163190] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [368.163881] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [368.164584] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [368.255312] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [368.255773] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [368.256463] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [368.257217] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [368.258002] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.258848] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.259616] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.260414] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.261122] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [368.261904] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [368.262611] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [368.263471] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [368.265076] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [368.265248] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [368.272664] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [368.272881] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [368.273265] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [368.279072] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [368.324377] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [368.324386] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [368.324389] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [368.324392] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [368.325601] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [368.325784] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [368.326128] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [368.326301] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [368.326334] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [368.332029] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [368.385303] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [368.386028] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [368.391999] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [368.393524] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [368.394310] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [368.395106] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [368.395779] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [368.396495] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [368.486309] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [368.486775] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [368.487475] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [368.488169] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [368.488929] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.489693] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.490448] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.491177] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.491834] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [368.492109] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [368.492281] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [368.492560] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [368.493277] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [368.493443] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [368.498486] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [368.498615] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [368.498918] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [368.503387] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2] <7> [368.548705] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [368.548714] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [368.548718] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD monitor fitHeadless4k <7> [368.548721] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:147:HDMI-A-2] ELD size 36, SAD count 0 <7> [368.548919] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [368.549076] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK on first message, retry <7> [368.549421] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc1] NAK for addr: 0040 w(1) <7> [368.549586] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6) <7> [368.549605] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-1] <7> [368.555293] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:158:HDMI-A-3] <7> [368.609297] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [368.610029] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [368.616090] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [368.618012] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [368.619143] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [368.620319] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [368.621167] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [368.621924] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <6> [368.700585] [IGT] i915_pm_rpm: finished subtest system-suspend-execbuf, SUCCESS <7> [368.702663] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:147:HDMI-A-2] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36) <7> [368.703400] i915 0000:00:02.0: [drm:intel_hdmi_compute_clock [i915]] picking 8 bpc for HDMI output (pipe bpp: 24) <7> [368.704006] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:82:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0 <7> [368.704686] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:146:DDI TC1/PHY C] [CRTC:82:pipe A] <7> [368.705321] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.enable (expected no, found yes) <7> [368.705962] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.active (expected no, found yes) <7> [368.706644] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0) <7> [368.707340] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in lane_count (expected 0, found 4) <7> [368.707976] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000040) <7> [368.708637] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1) <7> [368.709283] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 1920) <7> [368.709907] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 2360) <7> [368.710556] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 1920) <7> [368.711180] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 2360) <7> [368.711827] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 2008) <7> [368.712714] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2096) <7> [368.713384] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1080) <7> [368.714023] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1080) <7> [368.714680] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1084) <7> [368.715251] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1089) <7> [368.715743] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1125) <7> [368.716265] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1125) <7> [368.716755] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 1920) <7> [368.717259] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 2360) <7> [368.717750] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 1920) <7> [368.718155] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 2360) <7> [368.718554] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 2008) <7> [368.718927] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2096) <7> [368.719313] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1080) <7> [368.719677] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1080) <7> [368.720040] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1084) <7> [368.720431] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1089) <7> [368.720815] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1125) <7> [368.721110] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1125) <7> [368.721377] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1) <7> [368.721627] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.flags (1) (expected 0, found 1) <7> [368.721874] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.flags (4) (expected 0, found 4) <7> [368.722121] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24) <7> [368.722381] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 139929) <7> [368.722637] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 139929) <7> [368.722888] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:82:pipe A] fastset requirement not met in port_clock (expected 0, found 139929) <7> [368.723138] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:82:pipe A] fastset requirement not met, forcing full modeset <7> [368.723430] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x1 -> 0x3 (total dbuf slices 0x3), mbus joined? no->no <7> [368.723675] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:82:pipe A] dbuf slices 0x0 -> 0x3, ddb (0 - 0) -> (0 - 2048), active pipes 0x0 -> 0x1 <7> [368.723925] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] ddb ( 0 - 0) -> ( 0 - 2016), size 0 -> 2016 <7> [368.724093] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:77:cursor A] ddb ( 0 - 0) -> (2016 - 2048), size 0 -> 32 <7> [368.724270] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm, swm, stwm <7> [368.724441] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 2, 2, 2, 2, 5, 8, 9, 0, 0, 0 <7> [368.724605] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 33, 33, 33, 33, 81, 129, 145, 30, 0, 0 <7> [368.724769] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:32:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 38, 38, 38, 38, 91, 143, 161, 31, 0, 0 <7> [368.724933] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:82:pipe A] data rate 559716 num active planes 1 <7> [368.725106] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 16761 required 560 <7> [368.725282] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] No SAGV, using single QGV point mask 0x1 <7> [368.725465] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:32:plane 1A] min cdclk (69965 kHz) > [CRTC:82:pipe A] min cdclk (0 kHz) <7> [368.725639] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (10932 kHz) > old min cdclk (0 kHz) <7> [368.725814] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 180000 kHz, actual 180000 kHz <7> [368.725994] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0 <7> [368.726160] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:82:pipe A] allocated DPLL 0 <7> [368.726335] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc [i915]] [CRTC:82:pipe A] reserving DPLL 0 <7> [368.726503] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:82:pipe A] enable: yes [modeset] <7> [368.726668] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: HDMI (0x40), output format: RGB, sink format: RGB <7> [368.726832] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0 <7> [368.726996] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [368.727165] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [368.727338] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0 <7> [368.727503] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [368.727667] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [368.727830] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0 <7> [368.727992] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2 <7> [368.728155] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "1920x1080": 53 139930 1920 2008 2096 2360 1080 1084 1089 1125 0x48 0x5 <7> [368.728328] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "1920x1080": 53 139930 1920 2008 2096 2360 1080 1084 1089 1125 0x48 0x5 <7> [368.728491] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=139929, hd=1920 hb=1920-2360 hs=2008-2096 ht=2360, vd=1080 vb=1080-1125 vs=1084-1089 vt=1125, flags=0x5 <7> [368.728654] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "1920x1080": 53 139929 1920 2008 2096 2360 1080 1084 1089 1125 0x40 0x5 <7> [368.728816] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=139929, hd=1920 hb=1920-2360 hs=2008-2096 ht=2360, vd=1080 vb=1080-1125 vs=1084-1089 vt=1125, flags=0x5 <7> [368.728979] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 139929, pipe src: 1920x1080+0+0, pixel rate 139929 <7> [368.729141] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 135, ips linetime: 0 <7> [368.729343] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [368.729511] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [368.729677] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [368.729841] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: cfgcr0: 0x1a6655d, cfgcr1: 0xe84, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [368.730005] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [368.730167] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [368.730339] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [368.730501] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [368.730663] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [368.730825] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [368.730987] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [368.731156] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [368.731329] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [368.731492] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [368.731655] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [368.731817] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [368.731984] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:32:plane 1A] fb: [FB:162] 1920x1080 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7> [368.732153] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7> [368.732328] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 1920.000000x1080.000000+0.000000+0.000000 dst: 1920x1080+0+0 <7> [368.732493] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:41:plane 2A] fb: [NOFB], visible: no <7> [368.732657] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:50:plane 3A] fb: [NOFB], visible: no <7> [368.732821] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:59:plane 4A] fb: [NOFB], visible: no <7> [368.732989] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:68:plane 5A] fb: [NOFB], visible: no <7> [368.733155] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:77:cursor A] fb: [NOFB], visible: no <7> [368.745261] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [368.745385] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [368.745556] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [368.745760] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [368.746012] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.746267] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.746500] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.746730] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [368.746940] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [368.747703] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [368.747869] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [368.748157] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [368.748890] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [368.749060] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [368.755236] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [368.755379] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [368.755614] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [368.756460] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [368.757859] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [368.758040] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:136:DDI B/PHY B] <7> [368.758203] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:146:DDI TC1/PHY C] <7> [368.758380] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:150:DDI TC2/PHY D] <7> [368.758543] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:152:DP-MST A] <7> [368.758705] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:153:DP-MST B] <7> [368.758897] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3 <7> [368.759100] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:82:pipe A] <7> [368.759277] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0 <7> [368.759505] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_TC1 <7> [368.759710] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A <7> [368.760500] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 17694720 bytes of contiguous stolen space for FBC, limit: 1 <7> [368.760665] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:32:plane 1A] <7> [368.779632] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:147:HDMI-A-2] <7> [368.780057] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:82:pipe A] <7> [368.781135] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:137:HDMI-A-1] <7> [368.781689] i915 0000:00:02.0: [drm:drm_client_dev_restore] intel-fbdev: ret=0 <6> [368.782878] [IGT] i915_pm_rpm: exiting, ret=0 <6> [368.784742] Console: switching to colour frame buffer device 240x67 <7> [368.786259] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:147:HDMI-A-2]

Created at 2024-12-14 04:39:21