Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.18 seconds
Igt-Version 
IGT-Version: 2.4-g8214859d2 (x86_64) (Linux: 7.1.0-rc2-next-20260504-next-20260504-g9d0d467c3572+ x86_64)
Out 
Using IGT_SRANDOM=1777933779 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff8881233417b8 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x62/0x150 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1e0 [i915]
     intel_atomic_commit_tail+0x1bba/0x20f0 [i915]
     intel_atomic_commit+0x2ff/0x350 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x548/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1250/0x26e0
     do_syscall_64+0x103/0x13d0
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.181s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.181s)
Dmesg
<7> [100.138840] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [100.139094] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.139301] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.139503] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<6> [100.139897] Console: switching to colour dummy device 80x25
<6> [100.139966] [IGT] kms_pm_rpm: executing
<7> [100.140168] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.148537] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [100.152319] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [100.152326] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [100.152535] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.157468] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [100.157814] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [100.157832] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [100.158474] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.159018] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.159601] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [100.160365] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [100.160858] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [100.161467] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [100.161811] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [100.161816] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [100.162276] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.162476] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.162935] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.163155] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.163159] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.163338] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.167598] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.167603] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.167855] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [100.168095] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [100.168100] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [100.172389] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [100.172405] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [100.172409] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [100.173150] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [100.173614] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [100.174209] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [100.174225] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [100.174229] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [100.174680] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.174904] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.175330] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.175554] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.175558] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.175747] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.180170] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.180175] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.180370] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [100.180393] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [100.180396] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [100.184670] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [100.184711] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [100.184715] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [100.185515] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [100.185993] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [100.186601] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [100.186644] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [100.186648] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [100.187170] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.187354] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.187746] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.188022] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.188026] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.188222] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.192465] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.192469] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.192668] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [100.258962] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [100.259481] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.259980] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.260565] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.261627] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [111.251095] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [111.260564] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [111.285390] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [111.292750] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [111.294183] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [111.294760] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [111.295194] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [111.295886] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [111.296688] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [111.296627] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [111.301150] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [111.301488] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [111.302613] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [111.303397] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [111.304995] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [111.305181] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [111.305483] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [111.305706] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [111.306104] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [111.306329] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [111.306333] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [111.306566] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [111.310850] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [111.310855] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [111.314593] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [111.314820] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [111.315026] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [111.315227] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [111.315915] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [111.316394] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [111.321110] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [111.413074] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [111.426609] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [111.438557] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [111.445243] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [111.445889] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [111.446196] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [111.446788] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [111.447499] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [111.447417] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [111.451782] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [111.452183] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [111.453224] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [111.453997] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [111.455204] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [111.455697] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [111.455897] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [111.456316] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [111.456576] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [111.456581] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [111.456762] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [111.461003] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [111.461007] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [111.461368] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [111.465560] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [111.465786] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [111.465992] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [111.466193] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [111.466878] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [111.467199] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [111.470661] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [111.574503] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [111.589540] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [111.591286] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [111.591947] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [111.591939] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [111.592941] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [111.594823] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [111.598359] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [111.598761] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [111.599746] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [111.600539] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [111.601922] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [111.602377] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [111.602660] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [111.603080] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [111.603303] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [111.603308] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [111.603536] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [111.607761] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [111.607766] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [111.608234] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [111.608368] [IGT] kms_pm_rpm: exiting, ret=0
<6> [111.609678] Console: switching to colour frame buffer device 128x48
Created at 2026-05-05 05:20:12