Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 2.96 seconds
Igt-Version
IGT-Version: 2.4-g4963e78e0 (x86_64) (Linux: 7.0.0-next-20260422-next-20260422-g70c8a7ec6715+ x86_64)
Out
Using IGT_SRANDOM=1776864036 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88811f7057b8 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x1bb7/0x20c0 [i915]
     intel_atomic_commit+0x2ff/0x350 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x548/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1250/0x26e0
     do_syscall_64+0x103/0x1410
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Subtest basic-rte: SUCCESS (2.959s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 3
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88811f7057b8 has 1/3 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x1bb7/0x20c0 [i915]
     intel_atomic_commit+0x2ff/0x350 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x548/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1250/0x26e0
     do_syscall_64+0x103/0x1410
     entry_SYSCALL_64_after_hwframe+0x76/0x7e

ref_tracker: intel_runtime_pm@ffff88811f7057b8 has 2/3 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get+0x1a/0x30 [i915]
     intel_display_rpm_get+0x1f/0x30 [i915]
     intel_display_power_get+0x22/0x70 [i915]
     adlp_tc_phy_connect+0x166/0x2b0 [i915]
     intel_tc_port_reset_mode+0x285/0x3b0 [i915]
     __intel_tc_port_lock+0xe3/0x130 [i915]
     intel_tc_port_lock+0x1a/0x30 [i915]
     intel_digital_port_connected+0x33/0xa0 [i915]
     intel_dp_detect+0xfc/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
     i915_hpd_poll_init_work+0x20b/0x2e0 [i915]
Err
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (2.959s)
Dmesg
<6> [295.023781] Console: switching to colour dummy device 80x25
<6> [295.024297] [IGT] kms_pm_rpm: executing
<6> [295.027273] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [295.027588] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [295.034094] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:HDMI-A-1]
<7> [295.034108] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:399:HDMI-A-1]
<7> [295.038430] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:HDMI-A-1] disconnected
<7> [295.039017] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:DP-1]
<7> [295.039035] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:408:DP-1]
<7> [295.039761] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:DP-1] disconnected
<7> [295.040419] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:417:DP-2]
<7> [295.040426] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:417:DP-2]
<7> [295.041008] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:417:DP-2] disconnected
<7> [295.041971] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:eDP-1]
<7> [295.041987] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:390:eDP-1]
<7> [295.043685] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [295.044470] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [295.044894] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [295.045248] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [295.045753] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:390:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [295.045770] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:390:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [295.045779] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:390:eDP-1] ELD monitor
<7> [295.045788] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:390:eDP-1] ELD size 20, SAD count 0
<7> [295.045833] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:390:eDP-1] VRR capable: no
<7> [295.046277] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:390:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [295.046716] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:390:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [295.047817] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:eDP-1] probed modes:
<7> [295.047832] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [295.047844] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [295.047898] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:HDMI-A-1]
<7> [295.047910] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:399:HDMI-A-1]
<7> [295.052426] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:HDMI-A-1] disconnected
<7> [295.052469] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:DP-1]
<7> [295.052476] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:408:DP-1]
<7> [295.052860] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:DP-1] disconnected
<7> [295.052884] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:417:DP-2]
<7> [295.052890] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:417:DP-2]
<7> [295.053426] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:417:DP-2] disconnected
<7> [295.053494] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:eDP-1]
<7> [295.053506] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:390:eDP-1]
<7> [295.054426] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [295.055059] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [295.055475] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [295.055935] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000
<7> [295.056402] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:390:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [295.056416] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:390:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [295.056425] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:390:eDP-1] ELD monitor
<7> [295.056433] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:390:eDP-1] ELD size 20, SAD count 0
<7> [295.056478] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:390:eDP-1] VRR capable: no
<7> [295.056892] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:390:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [295.057274] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:390:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [295.058364] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:eDP-1] probed modes:
<7> [295.058381] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [295.058393] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [295.058548] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:HDMI-A-1]
<7> [295.058562] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:399:HDMI-A-1]
<7> [295.063129] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:HDMI-A-1] disconnected
<7> [295.063212] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:DP-1]
<7> [295.063219] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:408:DP-1]
<7> [295.063610] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:DP-1] disconnected
<7> [295.063714] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:417:DP-2]
<7> [295.063725] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:417:DP-2]
<7> [295.064396] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:417:DP-2] disconnected
<7> [295.065182] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:424]
<7> [296.092766] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [296.093800] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [296.094791] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [296.094765] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [296.096068] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [296.097000] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [296.099171] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A]
<7> [296.099490] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [296.100045] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [296.100259] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [296.100479] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [296.100698] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 7843931/8388608 link 522928/524288, found tu 0, data 0/0 link 0/0)
<7> [296.100908] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [296.101116] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [296.101324] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3840, found 0)
<7> [296.101536] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 4000, found 0)
<7> [296.101748] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3840, found 0)
<7> [296.101955] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 4000, found 0)
<7> [296.102162] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3888, found 0)
<7> [296.102369] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3920, found 0)
<7> [296.102569] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 2160, found 0)
<7> [296.102781] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 2161, found 0)
<7> [296.102988] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 2163, found 0)
<7> [296.103194] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 2168, found 0)
<7> [296.103428] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 2244, found 0)
<7> [296.103639] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 2244, found 0)
<7> [296.103846] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3840, found 0)
<7> [296.104053] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 4000, found 0)
<7> [296.104258] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3840, found 0)
<7> [296.104476] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 4000, found 0)
<7> [296.104686] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3888, found 0)
<7> [296.104893] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3920, found 0)
<7> [296.105098] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 2160, found 0)
<7> [296.105305] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 2161, found 0)
<7> [296.105511] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 2163, found 0)
<7> [296.105721] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 2168, found 0)
<7> [296.105927] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 2244, found 0)
<7> [296.106134] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 2244, found 0)
<7> [296.106346] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [296.106564] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [296.106777] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [296.106986] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [296.107192] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 538600, found 0)
<7> [296.107415] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 538600, found 0)
<7> [296.107631] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [296.107840] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in set_context_latency (expected 1, found 0)
<7> [296.108047] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [296.108261] i915 0000:00:02.0: [drm:intel_dpll_crtc_put [i915]] [CRTC:151:pipe A] releasing DPLL 0
<7> [296.108528] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [296.108724] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:151:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [296.108950] i915 0000:00:02.0: [drm:skl_print_plane_ddb_changes [i915]] [PLANE:35:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [296.109145] i915 0000:00:02.0: [drm:skl_print_plane_ddb_changes [i915]] [PLANE:145:cursor A] ddb (4027 - 4096) -> ( 0 - 0), size 69 -> 0
<7> [296.109335] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [296.109534] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [296.109734] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [296.109969] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [296.110255] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [296.110524] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 0
<7> [296.110770] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 0
<7> [296.111009] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 0
<7> [296.111232] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 0
<7> [296.111451] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0
<7> [296.111668] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 0
<7> [296.111874] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 0
<7> [296.112080] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:151:pipe A] min cdclk: 269300 kHz -> 0 kHz
<7> [296.112310] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 33663 kHz -> 0 kHz
<7> [296.112556] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [296.112769] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 179200 kHz, actual 179200 kHz
<7> [296.112979] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [296.113195] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:151:pipe A] enable: no [modeset]
<7> [296.113427] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:35:plane 1A] fb: [NOFB], visible: no
<7> [296.113655] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [296.113873] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [296.114085] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [296.114301] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [296.114523] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [296.114830] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR2
<7> [296.115684] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]
<7> [296.324704] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:390:eDP-1] set backlight PWM = 0
<7> [296.325840] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [296.333053] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 turn panel power off
<7> [296.333725] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [296.334320] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [296.389028] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [296.389949] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:389:DDI A/PHY A] - long
<7> [296.390769] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [296.391643] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:389:DDI A/PHY A]
<7> [296.395447] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [296.396004] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A
<7> [296.396600] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:151:pipe A]
<7> [296.397195] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disabling DPLL 0
<7> [296.397731] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [296.398256] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 179200 kHz, VCO 537600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [296.398822] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=448
<7> [296.399281] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:389:DDI A/PHY A]
<7> [296.399813] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:398:DDI B/PHY B]
<7> [296.400279] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:407:DDI TC1/PHY TC1]
<7> [296.400788] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:409:DP-MST A]
<7> [296.401269] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:410:DP-MST B]
<7> [296.401739] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:411:DP-MST C]
<7> [296.402210] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:416:DDI TC2/PHY TC2]
<7> [296.402730] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:418:DP-MST A]
<7> [296.403214] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:419:DP-MST B]
<7> [296.403714] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:420:DP-MST C]
<7> [296.404188] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:390:eDP-1]
<7> [296.405055] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 2 (mbus joined: no)
<7> [296.405547] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: yes -> no (pipe: *)
<7> [296.406007] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [296.406654] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_A
<7> [296.407288] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:151:pipe A]
<7> [296.408472] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B]
<7> [296.408938] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [296.426565] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [296.427448] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [296.428204] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [296.429239] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [296.431781] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [296.433263] i915 0000:00:02.0: [drm:intel_uc_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [296.434565] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [296.435630] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [296.437412] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [296.438032] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [296.438536] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [296.440018] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [296.512172] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A]
<7> [296.524563] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [296.525177] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [296.526125] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [296.527074] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [296.527933] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [296.528680] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [296.529382] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [296.530073] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [296.530616] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [296.531869] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [296.536473] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [296.536963] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [296.541449] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [296.542281] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [296.542728] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [296.543242] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [296.544054] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [296.545155] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:399:HDMI-A-1]
<7> [296.545687] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B]
<7> [296.550539] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:408:DP-1]
<7> [296.550958] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [296.551267] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [296.552552] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [296.553311] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [296.553916] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:417:DP-2]
<7> [296.554745] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [296.555834] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [296.556370] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [296.557211] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [296.575607] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [296.576448] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [296.577111] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [297.564518] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [297.565627] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [297.566923] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [297.567731] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [297.568406] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [297.569004] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [297.569575] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [297.570487] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [297.570477] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [297.570980] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [297.571617] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [297.572175] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [297.572735] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [297.573292] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [297.573802] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [297.574648] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [297.575230] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [297.575193] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [297.576953] i915 0000:00:02.0: [drm:intel_uc_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [297.578285] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [297.579361] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [297.581704] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [297.582418] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [297.582954] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [297.583599] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [297.663736] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A]
<7> [297.663885] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CONNECTOR:390:eDP-1]
<7> [297.664376] i915 0000:00:02.0: [drm:compute_baseline_pipe_bpp [i915]] [CONNECTOR:390:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [297.665485] i915 0000:00:02.0: [drm:intel_dp_compute_config_limits [i915]] [ENCODER:389:DDI A/PHY A][CRTC:151:pipe A] DP link limits: pixel clock 538600 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [297.666381] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp input 30 compressed 0.0000 HDR no link rate required 2019750 available 2160000
<7> [297.667155] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:151:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [297.667976] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:389:DDI A/PHY A] [CRTC:151:pipe A]
<7> [297.668655] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [297.668916] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [297.669123] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [297.669343] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [297.669556] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [297.669764] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [297.669970] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3840)
<7> [297.670176] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 4000)
<7> [297.670394] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3840)
<7> [297.670606] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 4000)
<7> [297.670821] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3888)
<7> [297.671045] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3920)
<7> [297.671284] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 2160)
<7> [297.671505] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 2161)
<7> [297.671727] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 2163)
<7> [297.671938] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 2168)
<7> [297.672147] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 2244)
<7> [297.672376] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 2244)
<7> [297.672603] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3840)
<7> [297.672824] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 4000)
<7> [297.673038] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3840)
<7> [297.673266] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 4000)
<7> [297.673487] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3888)
<7> [297.673694] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3920)
<7> [297.673901] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 2160)
<7> [297.674119] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 2161)
<7> [297.674356] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 2163)
<7> [297.674593] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 2168)
<7> [297.674808] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 2244)
<7> [297.675022] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 2244)
<7> [297.675238] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [297.675451] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [297.675667] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [297.675892] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [297.676117] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [297.676353] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in set_context_latency (expected 0, found 1)
<7> [297.676577] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [297.676862] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [297.677062] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:151:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [297.677305] i915 0000:00:02.0: [drm:skl_print_plane_ddb_changes [i915]] [PLANE:35:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [297.677509] i915 0000:00:02.0: [drm:skl_print_plane_ddb_changes [i915]] [PLANE:145:cursor A] ddb ( 0 - 0) -> (4027 - 4096), size 0 -> 69
<7> [297.677713] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [297.677915] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [297.678118] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [297.678328] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [297.678555] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:151:pipe A] data rate 2154400 num active planes 1
<7> [297.678773] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263
<7> [297.678993] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263
<7> [297.679227] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263
<7> [297.679447] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263
<7> [297.679662] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263
<7> [297.679868] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263
<7> [297.680071] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263
<7> [297.680296] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:151:pipe A] min cdclk: 0 kHz -> 269300 kHz
<7> [297.680544] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 0 kHz -> 33663 kHz
<7> [297.680791] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [297.681004] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 307200 kHz, actual 307200 kHz
<7> [297.681236] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [297.681459] i915 0000:00:02.0: [drm:intel_find_dpll [i915]] [CRTC:151:pipe A] allocated DPLL 0
<7> [297.681665] i915 0000:00:02.0: [drm:intel_dpll_crtc_get [i915]] [CRTC:151:pipe A] reserving DPLL 0
<7> [297.681880] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:151:pipe A] enable: yes [modeset]
<7> [297.682099] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [297.682339] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [297.682564] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [297.682778] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [297.682988] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0
<7> [297.683203] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [297.683418] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64
<7> [297.683635] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [297.683859] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: disabled
<7> [297.684083] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sdp split: disabled
<7> [297.684318] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [297.684537] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] minimum HBlank: 0
<7> [297.684747] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [297.684967] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] DP SDP: VSC, revision 4, length 14
<7> [297.685189] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pixelformat: RGB
<7> [297.685429] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] colorimetry: sRGB
<7> [297.685650] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bpc: 0
<7> [297.685863] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dynamic range: VESA range
<7> [297.686069] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] content type: Not defined
<7> [297.686292] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] scanline offset: 1
<7> [297.686511] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0, set context latency: 1
<7> [297.686730] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, fixed rr: yes, vmin: 2244, vmax: 2244, flipline: 2244, pipeline full: 0, guardband: 82 vsync start: 81, vsync end: 76
<7> [297.686952] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: vmin vblank: 2162, vmax vblank: 2162, vmin vtotal: 2244, vmax vtotal: 2244
<7> [297.687178] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [297.687412] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [297.687631] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [297.687841] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [297.688060] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [297.688294] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [297.688520] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600, min cdclk 269300
<7> [297.688736] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0
<7> [297.688953] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [297.689159] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [297.689382] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [297.689601] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0
<7> [297.689823] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [297.690044] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [297.690278] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [297.690500] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [297.690708] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [297.690916] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [297.691135] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [297.691373] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [297.691596] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [297.691806] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [297.692021] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [297.692243] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [297.692456] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [297.692664] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:35:plane 1A] fb: [FB:424] 3840x2160 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [297.692874] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [297.693091] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3840.000000x2160.000000+0.000000+0.000000 dst: 3840x2160+0+0
<7> [297.693332] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [297.693563] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [297.693776] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [297.693985] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [297.694200] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [297.706293] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [297.706471] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [297.706670] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [297.706884] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [297.707143] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [297.707415] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [297.707692] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [297.708076] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [297.708396] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [297.708786] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [297.711494] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [297.711717] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [297.714904] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [297.715494] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [297.716839] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [297.718837] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [297.719239] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [297.719846] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A
<7> [297.720104] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [297.720409] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=768
<7> [297.720728] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:389:DDI A/PHY A]
<7> [297.721090] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:398:DDI B/PHY B]
<7> [297.721508] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:407:DDI TC1/PHY TC1]
<7> [297.721910] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:409:DP-MST A]
<7> [297.722312] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:410:DP-MST B]
<7> [297.722694] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:411:DP-MST C]
<7> [297.722909] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:416:DDI TC2/PHY TC2]
<7> [297.723226] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:418:DP-MST A]
<7> [297.723624] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:419:DP-MST B]
<7> [297.724034] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:420:DP-MST C]
<7> [297.724714] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf
<7> [297.725040] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: no -> yes (pipe: *)
<7> [297.725288] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 4 (mbus joined: yes)
<7> [297.725769] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [297.726247] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:151:pipe A]
<7> [297.726678] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enabling DPLL 0
<7> [297.727126] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 turn panel power on
<7> [297.727337] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [297.727582] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [297.737319] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [297.737674] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 wait for panel power on
<7> [297.737987] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [297.799846] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [297.800744] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:389:DDI A/PHY A] - long
<7> [297.801561] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [297.802380] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:389:DDI A/PHY A]
<7> [297.949598] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [297.950684] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A
<7> [297.952019] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 turning VDD on
<7> [297.952983] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [297.955727] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 14 44 41 00 00 01 c0 02 00 02 00 00 0b 80
<7> [297.955768] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [297.956332] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 06
<7> [297.957259] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [297.957550] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [297.958442] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Clock recovery OK
<7> [297.958631] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [297.959983] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [297.960471] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [297.961510] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [297.962423] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [297.962901] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [297.963422] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:390:eDP-1] Performing OUI wait (0 ms)
<7> [297.964320] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:390:eDP-1] set backlight PWM = 6844
<7> [297.979313] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2
<7> [297.982448] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:390:eDP-1]
<7> [297.983491] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:151:pipe A]
<7> [297.985970] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:399:HDMI-A-1]
<6> [297.988180] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [297.988604] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A]
<7> [297.990958] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:408:DP-1]
<7> [297.991839] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [297.992672] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:417:DP-2]
<7> [297.993392] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [297.994362] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected yes, found no)
<7> [297.994887] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected yes, found no)
<7> [297.995542] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)
<7> [297.996129] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [297.996665] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 7843931/8388608 link 522928/524288, found tu 0, data 0/0 link 0/0)
<7> [297.997215] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [297.997750] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [297.998320] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3840, found 0)
<7> [297.998823] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 4000, found 0)
<7> [297.999329] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3840, found 0)
<7> [297.999831] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 4000, found 0)
<7> [298.000364] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3888, found 0)
<7> [298.000881] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3920, found 0)
<7> [298.001398] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 2160, found 0)
<7> [298.001904] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 2161, found 0)
<7> [298.002423] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 2163, found 0)
<7> [298.002917] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 2168, found 0)
<7> [298.003443] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 2244, found 0)
<7> [298.003953] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 2244, found 0)
<7> [298.004493] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3840, found 0)
<7> [298.004995] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 4000, found 0)
<7> [298.005518] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3840, found 0)
<7> [298.005999] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 4000, found 0)
<7> [298.006542] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3888, found 0)
<7> [298.007061] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3920, found 0)
<7> [298.007598] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 2160, found 0)
<7> [298.008100] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 2161, found 0)
<7> [298.008611] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 2163, found 0)
<7> [298.009109] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 2168, found 0)
<7> [298.009638] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 2244, found 0)
<7> [298.010174] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 2244, found 0)
<7> [298.010676] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [298.011192] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [298.011705] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [298.012134] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 30, found 0)
<7> [298.012640] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 538600, found 0)
<7> [298.013175] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 538600, found 0)
<7> [298.013707] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [298.014300] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in set_context_latency (expected 1, found 0)
<7> [298.014824] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [298.015260] i915 0000:00:02.0: [drm:intel_dpll_crtc_put [i915]] [CRTC:151:pipe A] releasing DPLL 0
<7> [298.015850] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0x1 (total dbuf slices 0xf), mbus joined? yes->no
<7> [298.016372] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:151:pipe A] dbuf slices 0xf -> 0x0, ddb (0 - 4096) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [298.016928] i915 0000:00:02.0: [drm:skl_print_plane_ddb_changes [i915]] [PLANE:35:plane 1A] ddb ( 0 - 4027) -> ( 0 - 0), size 4027 -> 0
<7> [298.017414] i915 0000:00:02.0: [drm:skl_print_plane_ddb_changes [i915]] [PLANE:145:cursor A] ddb (4027 - 4096) -> ( 0 - 0), size 69 -> 0
<7> [298.017874] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [298.018242] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] lines 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [298.018656] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] blocks 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [298.019123] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] min_ddb 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [298.019686] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:151:pipe A] data rate 0 num active planes 0
<7> [298.020204] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 0
<7> [298.020696] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 0
<7> [298.021125] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 0
<7> [298.021451] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 0
<7> [298.021812] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0
<7> [298.022343] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 0
<7> [298.022847] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 0
<7> [298.023360] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:151:pipe A] min cdclk: 269300 kHz -> 0 kHz
<7> [298.023903] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 33663 kHz -> 0 kHz
<7> [298.024412] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [298.024924] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 179200 kHz, actual 179200 kHz
<7> [298.025444] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [298.025953] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:151:pipe A] enable: no [modeset]
<7> [298.026351] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:35:plane 1A] fb: [NOFB], visible: no
<7> [298.026846] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [298.027379] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [298.027897] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [298.028420] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [298.028907] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [298.029314] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR2
<7> [298.047598] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]
<7> [298.252413] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:390:eDP-1] set backlight PWM = 0
<7> [298.254614] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [298.263568] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 turn panel power off
<7> [298.263810] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x00000089, pins 0x00000010, long 0x00000000
<7> [298.264315] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [298.264520] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:389:DDI A/PHY A] - short
<7> [298.264953] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [298.319562] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [298.320483] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:389:DDI A/PHY A] - long
<7> [298.321302] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [298.325173] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [298.325821] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A
<7> [298.326483] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:151:pipe A]
<7> [298.326877] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring short hpd on eDP [ENCODER:389:DDI A/PHY A]
<7> [298.327178] i915 0000:00:02.0: [drm:intel_dpll_disable [i915]] disabling DPLL 0
<7> [298.327412] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:389:DDI A/PHY A]
<7> [298.327707] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [298.328274] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 179200 kHz, VCO 537600 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [298.328899] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=448
<7> [298.329371] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:389:DDI A/PHY A]
<7> [298.329610] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:398:DDI B/PHY B]
<7> [298.329814] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:407:DDI TC1/PHY TC1]
<7> [298.330012] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:409:DP-MST A]
<7> [298.330221] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:410:DP-MST B]
<7> [298.330429] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:411:DP-MST C]
<7> [298.330644] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:416:DDI TC2/PHY TC2]
<7> [298.330875] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:418:DP-MST A]
<7> [298.331110] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:419:DP-MST B]
<7> [298.331368] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:420:DP-MST C]
<7> [298.331600] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:390:eDP-1]
<7> [298.331988] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 2 (mbus joined: no)
<7> [298.332282] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: yes -> no (pipe: *)
<7> [298.332497] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [298.332788] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_A
<7> [298.333059] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:151:pipe A]
<7> [298.333665] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B]
<7> [298.333893] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C]
<7> [298.351327] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [298.352205] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [298.352930] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [299.036413] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [299.037549] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [299.038816] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [299.039788] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [299.040639] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [299.041425] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [299.041856] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [299.042396] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [299.042390] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [299.042906] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [299.043505] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [299.043738] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [299.043955] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [299.044184] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [299.044396] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [299.044920] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [299.045149] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (tbt-alt -> disconnected) pin assignment: - max lanes: 4
<7> [299.045192] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [299.046069] i915 0000:00:02.0: [drm:intel_uc_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [299.047360] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [299.048359] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [299.049064] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [299.049689] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [299.050197] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [299.050741] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [299.142857] i915 0000:00:02.0: [drm:compute_baseline_pipe_bpp [i915]] [CONNECTOR:390:eDP-1] Limiting target display pipe bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)
<7> [299.143600] i915 0000:00:02.0: [drm:intel_dp_compute_config_limits [i915]] [ENCODER:389:DDI A/PHY A][CRTC:151:pipe A] DP link limits: pixel clock 538600 kHz DSC off max lanes 4 max rate 810000 max pipe_bpp 30 min link_bpp 18.0000 max link_bpp 30.0000
<7> [299.144165] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp input 30 compressed 0.0000 HDR no link rate required 2019750 available 2160000
<7> [299.144396] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:151:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0
<7> [299.144633] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:389:DDI A/PHY A] [CRTC:151:pipe A]
<7> [299.144846] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.enable (expected no, found yes)
<7> [299.145089] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.active (expected no, found yes)
<7> [299.145314] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)
<7> [299.145538] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [299.145748] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [299.145960] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [299.146294] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3840)
<7> [299.146522] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 4000)
<7> [299.146746] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3840)
<7> [299.146970] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 4000)
<7> [299.147229] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3888)
<7> [299.147464] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3920)
<7> [299.147685] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 2160)
<7> [299.147898] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 2161)
<7> [299.148125] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 2163)
<7> [299.148355] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 2168)
<7> [299.148591] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 2244)
<7> [299.148831] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 2244)
<7> [299.149084] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3840)
<7> [299.149320] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 4000)
<7> [299.149531] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3840)
<7> [299.149741] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 4000)
<7> [299.149965] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3888)
<7> [299.150208] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3920)
<7> [299.150444] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 2160)
<7> [299.150666] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 2161)
<7> [299.150887] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 2163)
<7> [299.151220] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 2168)
<7> [299.151450] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 2244)
<7> [299.151681] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 2244)
<7> [299.151920] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [299.152332] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [299.152572] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [299.152802] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 30)
<7> [299.153022] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [299.153249] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] [CRTC:151:pipe A] fastset requirement not met in set_context_latency (expected 0, found 1)
<7> [299.153471] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:151:pipe A] fastset requirement not met, forcing full modeset
<7> [299.153800] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x1 -> 0xf (total dbuf slices 0xf), mbus joined? no->yes
<7> [299.154056] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:151:pipe A] dbuf slices 0x0 -> 0xf, ddb (0 - 0) -> (0 - 4096), active pipes 0x0 -> 0x1
<7> [299.154268] i915 0000:00:02.0: [drm:skl_print_plane_ddb_changes [i915]] [PLANE:35:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027
<7> [299.154472] i915 0000:00:02.0: [drm:skl_print_plane_ddb_changes [i915]] [PLANE:145:cursor A] ddb ( 0 - 0) -> (4027 - 4096), size 0 -> 69
<7> [299.154664] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm
<7> [299.154854] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0
<7> [299.155064] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201
<7> [299.155271] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207
<7> [299.155516] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:151:pipe A] data rate 2154400 num active planes 1
<7> [299.155750] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263
<7> [299.155969] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263
<7> [299.156255] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263
<7> [299.156482] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263
<7> [299.156689] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263
<7> [299.156897] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263
<7> [299.157128] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263
<7> [299.157358] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] [CRTC:151:pipe A] min cdclk: 0 kHz -> 269300 kHz
<7> [299.157623] i915 0000:00:02.0: [drm:intel_cdclk_update_dbuf_bw_min_cdclk [i915]] dbuf bandwidth min cdclk: 0 kHz -> 33663 kHz
<7> [299.157859] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] Modeset required for cdclk change
<7> [299.158101] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New cdclk calculated to be logical 307200 kHz, actual 307200 kHz
<7> [299.158327] i915 0000:00:02.0: [drm:intel_cdclk_atomic_check [i915]] New voltage level calculated to be logical 0, actual 0
<7> [299.158540] i915 0000:00:02.0: [drm:intel_find_dpll [i915]] [CRTC:151:pipe A] allocated DPLL 0
<7> [299.158765] i915 0000:00:02.0: [drm:intel_dpll_crtc_get [i915]] [CRTC:151:pipe A] reserving DPLL 0
<7> [299.159026] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:151:pipe A] enable: yes [modeset]
<7> [299.159262] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [299.159481] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0
<7> [299.159702] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [299.159910] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [299.160136] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0
<7> [299.160356] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [299.160580] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64
<7> [299.160818] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [299.161076] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: disabled
<7> [299.161320] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sdp split: disabled
<7> [299.161539] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] psr: enabled, selective update: enabled, panel replay: disabled, selective fetch: enabled
<7> [299.161748] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] minimum HBlank: 0
<7> [299.161963] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [299.162218] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] DP SDP: VSC, revision 4, length 14
<7> [299.162449] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pixelformat: RGB
<7> [299.162668] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] colorimetry: sRGB
<7> [299.162892] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bpc: 0
<7> [299.163131] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dynamic range: VESA range
<7> [299.163354] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] content type: Not defined
<7> [299.163574] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] scanline offset: 1
<7> [299.163794] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0, set context latency: 1
<7> [299.164056] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, fixed rr: yes, vmin: 2244, vmax: 2244, flipline: 2244, pipeline full: 0, guardband: 82 vsync start: 81, vsync end: 76
<7> [299.164296] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: vmin vblank: 2162, vmax vblank: 2162, vmin vtotal: 2244, vmax vtotal: 2244
<7> [299.164523] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0
<7> [299.164750] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [299.164966] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa
<7> [299.165199] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [299.165424] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa
<7> [299.165648] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2161-2244 vs=2163-2168 vt=2244, flags=0xa
<7> [299.165884] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600, min cdclk 269300
<7> [299.166165] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0
<7> [299.166398] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [299.166614] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [299.166822] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [299.167047] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0
<7> [299.167275] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [299.167499] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [299.167727] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [299.167952] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [299.168200] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [299.168437] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [299.168651] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [299.168861] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [299.169098] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [299.169330] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [299.169554] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [299.169774] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [299.169997] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0
<7> [299.170229] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:35:plane 1A] fb: [FB:391] 3840x2160 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [299.170456] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [299.170681] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3840.000000x2160.000000+0.000000+0.000000 dst: 3840x2160+0+0
<7> [299.170921] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:65:plane 2A] fb: [NOFB], visible: no
<7> [299.171167] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:95:plane 3A] fb: [NOFB], visible: no
<7> [299.171402] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:125:plane 4A] fb: [NOFB], visible: no
<7> [299.171628] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:135:plane 5A] fb: [NOFB], visible: no
<7> [299.171838] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:145:cursor A] fb: [NOFB], visible: no
<7> [299.184410] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [299.184603] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [299.184803] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [299.185042] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [299.185423] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [299.185932] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [299.186483] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [299.187030] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [299.187265] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [299.187751] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [299.190843] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [299.191079] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [299.195829] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [299.197541] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [299.198634] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [299.199161] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [299.199632] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [299.200277] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A
<7> [299.200744] i915 0000:00:02.0: [drm:intel_set_cdclk [i915]] Pre changing CDCLK to 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [299.201203] i915 0000:00:02.0: [drm:intel_audio_cdclk_change_post.part.0 [i915]] aud_ts_cdclk set to M=60, N=768
<7> [299.201668] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:389:DDI A/PHY A]
<7> [299.202056] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:398:DDI B/PHY B]
<7> [299.202419] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:407:DDI TC1/PHY TC1]
<7> [299.202772] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:409:DP-MST A]
<7> [299.203146] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:410:DP-MST B]
<7> [299.203478] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:411:DP-MST C]
<7> [299.203805] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:416:DDI TC2/PHY TC2]
<7> [299.204180] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:418:DP-MST A]
<7> [299.204530] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:419:DP-MST B]
<7> [299.204864] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:420:DP-MST C]
<7> [299.205455] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf
<7> [299.205859] i915 0000:00:02.0: [drm:intel_dbuf_mbus_join_update [i915]] Changing mbus joined: no -> yes (pipe: *)
<7> [299.206105] i915 0000:00:02.0: [drm:intel_dbuf_mdclk_cdclk_ratio_update [i915]] Updating dbuf ratio to 4 (mbus joined: yes)
<7> [299.206393] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [299.206732] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:151:pipe A]
<7> [299.207083] i915 0000:00:02.0: [drm:intel_dpll_enable [i915]] enabling DPLL 0
<7> [299.207500] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 turn panel power on
<7> [299.207793] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 wait for panel power cycle (0 ms remaining)
<7> [299.208089] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [299.218456] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [299.218816] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 wait for panel power on
<7> [299.219142] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063
<7> [299.280969] i915 0000:00:02.0: [drm:icp_irq_handler [i915]] hotplug event received, stat 0x00010000, dig 0x0000008a, pins 0x00000010, long 0x00000010
<7> [299.281880] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:389:DDI A/PHY A] - long
<7> [299.282698] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [299.283604] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:389:DDI A/PHY A]
<7> [299.436381] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [299.437480] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A
<7> [299.438810] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 turning VDD on
<7> [299.439626] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:389:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [299.442187] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 14 44 41 00 00 01 c0 02 00 02 00 00 0b 80
<7> [299.442226] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Reloading eDP link rates
<7> [299.442771] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 06
<7> [299.443721] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [299.444001] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [299.444890] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Clock recovery OK
<7> [299.445110] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [299.446379] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [299.446564] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:390:eDP-1][ENCODER:389:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [299.447145] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [299.447515] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [299.447697] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [299.447885] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:390:eDP-1] Performing OUI wait (0 ms)
<7> [299.448369] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:390:eDP-1] set backlight PWM = 6844
<7> [299.464429] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2
<7> [299.467697] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:390:eDP-1]
<7> [299.468703] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:151:pipe A]
<7> [299.471705] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [299.471736] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:399:HDMI-A-1]
<6> [299.473727] [IGT] kms_pm_rpm: exiting, ret=0
<7> [299.476491] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:408:DP-1]
<7> [299.477593] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port D/TC#1: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<7> [299.478343] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:417:DP-2]
<7> [299.479079] i915 0000:00:02.0: [drm:intel_tc_port_reset_mode [i915]] Port E/TC#2: TC port mode reset (disconnected -> tbt-alt) pin assignment: - max lanes: 4
<6> [299.481290] Console: switching to colour frame buffer device 240x67
Created at 2026-04-23 00:03:36