Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 11.44 seconds
Igt-Version 
IGT-Version: 2.4-g9b95600c4 (x86_64) (Linux: 7.0.0-next-20260416-next-20260416-g452c3b1ea875+ x86_64)
Out 
Using IGT_SRANDOM=1776350415 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888115cd17b8 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x140d/0x1d70 [i915]
     intel_atomic_commit+0x2e8/0x330 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x548/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1250/0x26e0
     do_syscall_64+0x103/0x1410
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Subtest basic-rte: SUCCESS (11.443s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff888115cd17b8 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     __gt_park+0x175/0x240 [i915]
     ____intel_wakeref_put_last+0x2e/0xb0 [i915]
     __intel_wakeref_put_last+0x72/0x90 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915]
     i915_forcewake_release+0x22/0x50 [i915]
     full_proxy_release+0x2e/0x50
     __fput+0x10a/0x300
     fput_close_sync+0x3d/0xa0
     __x64_sys_close+0x3e/0x90
     x64_sys_call+0x1b7c/0x26e0
     do_syscall_64+0x103/0x1410
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (11.443s)
Dmesg
<6> [394.741529] Console: switching to colour dummy device 80x25
<6> [394.741980] [IGT] kms_pm_rpm: executing
<7> [394.748229] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<6> [394.748528] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [394.748486] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [394.748685] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [394.748790] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [394.748879] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [394.749550] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [394.753020] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [394.753029] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [394.753285] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [394.757744] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [394.758072] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [394.758077] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [394.758750] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [394.759256] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [394.759823] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [394.760485] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [394.760973] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [394.761620] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [394.761949] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [394.761955] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [394.762465] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [394.762643] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [394.763036] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [394.763390] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [394.763395] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [394.763574] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [394.767902] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [394.767907] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [394.768162] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [394.768434] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [394.768440] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [394.772723] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [394.772740] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [394.772745] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [394.773495] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [394.773980] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [394.774604] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [394.774621] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [394.774625] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [394.775064] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [394.775345] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [394.775741] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [394.775952] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [394.775956] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [394.776162] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [394.780460] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [394.780465] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [394.780656] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [394.780680] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [394.780684] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [394.784921] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [394.784962] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [394.784966] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [394.785744] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [394.786242] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [394.786898] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [394.786939] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [394.786943] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [394.787411] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [394.787588] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [394.787969] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [394.788261] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [394.788266] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [394.788441] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [394.792713] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [394.792718] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [394.792912] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [394.860331] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [394.860860] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [394.861370] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [394.861974] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [394.863189] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [404.884047] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [404.891807] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [405.858854] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [405.866388] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [405.868064] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [405.867803] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [405.874814] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [405.899713] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [405.905578] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [405.906794] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [405.907166] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [405.907849] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [405.908688] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [405.908649] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [405.913140] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [405.913631] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [405.914870] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [405.915794] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [405.917411] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [405.917373] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [405.917862] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [405.918057] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [405.918456] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [405.918685] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [405.918690] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [405.918890] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [405.923071] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [405.923076] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [405.925850] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [405.926082] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [405.926298] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [405.926509] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [405.927200] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [405.927442] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [405.930632] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [406.024627] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [406.036890] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [406.045663] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [406.046849] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [406.047493] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [406.048371] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [406.049799] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [406.050254] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [406.054410] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [406.054950] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [406.056198] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [406.057110] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [406.058606] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [406.059217] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [406.059532] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [406.060073] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [406.060431] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [406.060440] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [406.060784] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [406.065048] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [406.065056] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [406.065650] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [406.066861] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [406.067243] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [406.067596] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [406.068002] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [406.068933] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [406.069333] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [406.073708] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [406.178552] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [406.186891] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [406.187433] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [406.188525] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [406.189585] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [406.190531] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<6> [406.192885] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [406.193576] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [406.195398] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [406.195988] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [406.197250] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [406.198174] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [406.199428] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [406.199886] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [406.200077] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [406.200467] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [406.200695] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [406.200700] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [406.200900] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [406.205272] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [406.205277] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [406.205652] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [406.205854] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [406.291905] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [406.292297] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [406.292652] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [406.293035] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [406.293983] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [406.294505] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [406.300815] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [406.422889] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [406.433930] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [406.434229] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [406.434447] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [406.435387] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [406.436269] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [406.436644] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<6> [406.437476] [IGT] kms_pm_rpm: exiting, ret=0
<7> [406.441018] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [406.441355] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [406.442345] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [406.443134] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<6> [406.445280] Console: switching to colour frame buffer device 128x48
<7> [406.445202] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [406.445781] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [406.445977] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [406.446372] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [406.446595] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [406.446600] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [406.446835] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [406.450833] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [406.450838] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [406.453782] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [406.454016] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [406.454232] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [406.454438] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [406.455109] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2026-04-17 02:40:37