Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 11.43 seconds
Igt-Version 
IGT-Version: 2.4-g8d537f073 (x86_64) (Linux: 7.0.0-next-20260415-next-20260415-g936c21068d7a+ x86_64)
Out 
Using IGT_SRANDOM=1776258337 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88811d7bd7b8 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x140d/0x1d70 [i915]
     intel_atomic_commit+0x2e8/0x330 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x548/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1250/0x26e0
     do_syscall_64+0x103/0x1410
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Subtest basic-rte: SUCCESS (11.431s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88811d7bd7b8 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     __gt_park+0x175/0x240 [i915]
     ____intel_wakeref_put_last+0x2e/0xb0 [i915]
     __intel_wakeref_put_last+0x72/0x90 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915]
     i915_forcewake_release+0x22/0x50 [i915]
     full_proxy_release+0x2e/0x50
     __fput+0x10a/0x300
     fput_close_sync+0x3d/0xa0
     __x64_sys_close+0x3e/0x90
     x64_sys_call+0x1b7c/0x26e0
     do_syscall_64+0x103/0x1410
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (11.431s)
Dmesg
<6> [88.755120] Console: switching to colour dummy device 80x25
<6> [88.755186] [IGT] kms_pm_rpm: executing
<6> [88.767614] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [88.767851] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [88.769317] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [88.769567] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [88.769783] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [88.769994] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [88.770686] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [88.772033] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [88.772041] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [88.772286] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [88.776821] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [88.777203] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [88.777210] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [88.777828] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [88.778369] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [88.778889] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [88.779545] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [88.780023] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [88.780603] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [88.780929] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [88.780935] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [88.781393] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [88.781580] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [88.781988] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [88.782206] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [88.782211] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [88.782401] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [88.786516] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [88.786521] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [88.786712] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [88.786950] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [88.786955] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [88.791223] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [88.791260] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [88.791265] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [88.792018] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [88.792503] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [88.793093] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [88.793110] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [88.793115] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [88.793620] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [88.793825] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [88.794256] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [88.794510] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [88.794514] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [88.794690] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [88.799015] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [88.799020] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [88.799267] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [88.799338] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [88.799344] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [88.803625] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [88.803666] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [88.803670] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [88.804426] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [88.804908] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [88.805596] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [88.805637] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [88.805641] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [88.806069] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [88.806290] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [88.806699] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [88.806911] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [88.806915] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [88.807121] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [88.811531] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [88.811536] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [88.811724] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [88.881374] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [88.881628] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [88.881844] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [88.882053] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [88.882757] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.866350] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [99.878568] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [99.903260] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [99.909545] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [99.910366] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [99.910166] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [99.910628] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [99.911349] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [99.912234] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [99.912146] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [99.916626] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [99.917206] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [99.918315] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [99.919079] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [99.920277] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [99.920736] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [99.920971] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [99.921384] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [99.921600] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [99.921604] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [99.921779] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [99.926007] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [99.926012] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [99.926352] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [99.931003] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [99.931241] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [99.931456] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [99.931669] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [99.932375] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [99.932598] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [99.935780] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.027587] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [100.039876] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.049752] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.050278] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.050776] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.052493] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.053728] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [100.053580] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [100.058333] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [100.058921] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [100.060164] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [100.060982] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [100.062368] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [100.062831] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.063040] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.063448] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.063702] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.063706] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.063905] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.068141] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.068145] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.068491] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [100.072013] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [100.072232] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.072429] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.072625] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.073339] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.073557] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.076961] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.181319] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.191533] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.192102] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.193667] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.194618] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.197887] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<6> [100.198647] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [100.199001] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [100.202510] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [100.202828] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [100.203802] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [100.204587] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [100.205841] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [100.206301] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.206479] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.206864] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.207118] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.207123] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.207301] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.211492] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.211496] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.211918] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [100.212071] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [100.304055] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [100.304496] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.304912] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.305334] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.306361] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [100.306835] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [100.311889] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [100.428025] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [100.440346] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [100.441841] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.442526] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [100.443568] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [100.446667] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [100.447148] [IGT] kms_pm_rpm: exiting, ret=0
<7> [100.447387] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [100.451980] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [100.452309] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [100.453274] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [100.454054] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<6> [100.455759] Console: switching to colour frame buffer device 128x48
<7> [100.455692] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [100.456308] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.456664] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.457063] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.457278] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.457283] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.457458] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.461719] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.461723] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.463953] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [100.464260] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [100.464539] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [100.464808] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [100.465612] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2026-04-15 16:50:24