Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.32 seconds
Igt-Version 
IGT-Version: 2.4-g8d537f073 (x86_64) (Linux: 7.0.0-next-20260415-next-20260415-g936c21068d7a+ x86_64)
Out 
Using IGT_SRANDOM=1776258363 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff8881183b57b8 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x9a0 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x30c/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.322s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.322s)
Dmesg
<6> [120.686248] Console: switching to colour dummy device 80x25
<6> [120.686350] [IGT] kms_pm_rpm: executing
<7> [120.690420] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [120.696554] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [120.696566] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [120.696868] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.698029] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [120.698672] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [120.699286] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [120.699832] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [120.700117] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [120.700904] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.702502] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.704018] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.705554] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.707257] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.708871] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.710598] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.712285] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.713860] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.714799] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [120.715740] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [120.716147] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [120.716765] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [120.717397] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2]
<7> [120.717406] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [120.721835] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2] disconnected
<7> [120.722372] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1]
<7> [120.722379] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [120.788156] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [120.793445] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.793513] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [120.794182] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [120.798270] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.798291] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [120.799078] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1] disconnected
<7> [120.800499] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [120.800530] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [120.802095] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [120.803040] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [120.803924] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [120.804806] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [120.805693] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [120.807369] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 4 ms
<7> [120.808875] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [120.810191] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [120.811306] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [120.812843] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.814783] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.816701] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.818437] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.820319] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.822114] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.823913] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.825660] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.827326] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.828350] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [120.829179] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [120.829643] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [120.830277] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [120.830321] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2]
<7> [120.830329] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [120.834824] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2] disconnected
<7> [120.834862] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1]
<7> [120.834870] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [120.900556] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [120.904643] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.904671] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [120.905545] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [120.909751] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.909773] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [120.910524] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1] disconnected
<7> [120.910689] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [120.910716] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [120.912376] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [120.913265] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [120.914873] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.917220] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.919666] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.922023] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.924553] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.927135] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.929626] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.932187] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.934530] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.935968] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [120.937410] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [120.938259] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [120.939781] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [120.940092] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2]
<7> [120.940121] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [120.945173] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2] disconnected
<7> [120.945372] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1]
<7> [120.945391] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [121.012103] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [121.016143] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.016165] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [121.016838] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [121.018697] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [121.019764] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [121.020811] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [121.021736] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [121.023210] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.023236] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [121.024509] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [121.025696] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1] disconnected
<7> [122.040829] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.047995] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.073336] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.083724] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.084739] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.085235] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [122.085475] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.086087] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.087474] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [122.087474] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [122.087962] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.089023] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.089373] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.090207] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.091840] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.093301] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.094893] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.096467] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.098218] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.099925] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.101501] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.103096] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.104076] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.105061] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.105778] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.107000] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [122.111420] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [122.179842] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.183631] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.183644] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.183963] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.187177] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.187188] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.187882] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [122.210303] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.210876] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.211427] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.211900] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.212861] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.214046] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.221373] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [122.292962] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [122.347689] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [122.359363] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.365703] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.366399] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.366737] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.367368] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.368046] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [122.368379] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [122.369130] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.369966] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.370399] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [122.371259] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.372752] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.374221] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.375759] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.377332] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.379079] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.380778] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.382380] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.383961] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.384886] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.385224] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.385550] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.385867] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.386144] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.387094] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.387734] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [122.388362] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.389297] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.390016] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.391207] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [122.395620] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [122.461203] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.464371] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.464382] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.464666] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.467831] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.467841] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.469672] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [122.498450] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.499070] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.499724] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.500404] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.501574] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.502343] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [122.510189] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [122.583306] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [122.605952] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [122.607879] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.609000] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [122.608983] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.610523] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [122.616884] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [122.616449] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [122.618881] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [122.620222] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 1 ms
<7> [122.622466] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.625100] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.626993] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.629047] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.630963] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.632986] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.634821] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.636681] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.638328] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [122.639336] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [122.640475] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [122.641293] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [122.642829] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [122.647398] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [122.713141] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [122.716490] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.716503] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [122.716819] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [122.720128] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [122.720140] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [122.720808] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [122.720924] [IGT] kms_pm_rpm: exiting, ret=0
<7> [122.723586] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [122.724013] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [122.724478] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [122.724984] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [122.726546] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [122.727145] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [122.727513] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [122.728248] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [122.729253] Console: switching to colour frame buffer device 128x48
Created at 2026-04-15 16:50:24