Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.43 seconds
Igt-Version	IGT-Version: 2.4-g574c502c4 (x86_64) (Linux: 7.0.0-rc6-next-20260403-next-20260403-g2febe6e6ee6e+ x86_64)
Out	Using IGT_SRANDOM=1775228741 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888134a297b8 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x140d/0x1d70 [i915] intel_atomic_commit+0x2e8/0x330 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x548/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1250/0x26e0 do_syscall_64+0x103/0x1420 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.427s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888134a297b8 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x2f0 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b7c/0x26e0 do_syscall_64+0x103/0x1420
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.427s)
Dmesg	<6> [67.576099] Console: switching to colour dummy device 80x25 <6> [67.576151] [IGT] kms_pm_rpm: executing <6> [67.578126] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [67.578339] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [67.583061] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [67.583068] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [67.587326] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [67.587569] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [67.587573] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [67.591759] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [67.592017] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [67.592021] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [67.596204] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [67.596476] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [67.596480] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [67.600700] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [67.600712] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [67.600715] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [67.604921] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [67.604933] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [67.604936] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [67.609173] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [67.609191] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] <7> [67.609194] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [67.611007] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [67.611177] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [67.611316] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [67.613894] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:390:HDMI-A-1] disconnected <7> [67.613935] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] <7> [67.613939] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [67.618760] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:400:DP-1] disconnected <7> [67.618791] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] <7> [67.618794] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [67.623636] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:408:HDMI-A-2] disconnected <7> [67.730309] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.626352] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [68.633625] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.635034] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.635470] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.635756] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.635916] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.637859] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [68.663028] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [68.669920] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.670087] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.670266] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.670505] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.671517] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.672498] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.673405] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.674315] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.676090] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [68.676891] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.677681] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.678374] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.678511] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.685868] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [68.687097] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.687208] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [68.687341] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.688302] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.689766] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [68.689722] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [68.693994] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [68.698231] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [68.702562] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [68.720076] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.720249] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.720395] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.721867] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.722425] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [68.726937] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.728348] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.728586] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.728877] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.729029] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.730889] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [68.803681] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [68.816067] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [68.824054] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.824897] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.825819] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.826772] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.827730] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.828658] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.829555] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.830420] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.831342] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [68.832149] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.833864] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.836357] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.837156] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.847515] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [68.847698] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.847943] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.848799] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.850267] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <7> [68.850454] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [68.854497] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [68.858841] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [68.858956] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [68.876130] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.876290] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.876431] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.877698] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.877867] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [68.881411] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.882830] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.883402] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.884000] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.884424] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.887833] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [68.972105] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [68.980069] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.980917] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.981833] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.982779] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.983705] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.984605] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.985487] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [68.986353] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.987951] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [68.988799] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.990262] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.992697] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.993424] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [69.002624] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [69.002802] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [69.003225] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <6> [69.004964] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [69.005265] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:151:pipe A] <7> [69.008568] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <7> [69.013470] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2] <7> [69.018436] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [69.019440] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [69.020894] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:269:pipe B] <7> [69.021002] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:387:pipe C] <7> [69.107521] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [69.108474] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [69.109307] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [69.112383] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [69.113351] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [69.121709] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [69.123483] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [69.124464] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [69.125389] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [69.126011] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [69.131166] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [69.239720] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [69.247348] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [69.248190] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [69.249159] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [69.250162] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [69.251131] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [69.252089] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [69.253035] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [69.253950] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [69.254900] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [69.255032] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [69.255402] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [69.256093] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [69.256244] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [69.266075] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [69.266249] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [69.266429] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [69.267269] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [69.268699] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [69.268696] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:390:HDMI-A-1] <6> [69.268921] [IGT] kms_pm_rpm: exiting, ret=0 <7> [69.272985] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:400:DP-1] <6> [69.277614] Console: switching to colour frame buffer device 160x45 <7> [69.277565] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:408:HDMI-A-2]

Created at 2026-04-04 03:50:30