Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.19 seconds
Igt-Version 
IGT-Version: 2.4-g574c502c4 (x86_64) (Linux: 7.0.0-rc6-next-20260403-next-20260403-g2febe6e6ee6e+ x86_64)
Out 
Using IGT_SRANDOM=1775228974 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff8881250897b8 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x140d/0x1d70 [i915]
     intel_atomic_commit+0x2e8/0x330 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x548/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1250/0x26e0
     do_syscall_64+0x103/0x1420
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.187s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.187s)
Dmesg
<7> [289.800068] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [289.800409] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [289.800691] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [289.801049] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [289.801829] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [289.808210] Console: switching to colour dummy device 80x25
<6> [289.809091] [IGT] kms_pm_rpm: executing
<7> [289.816659] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [289.820527] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [289.820536] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [289.820745] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [289.825245] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [289.825561] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [289.825567] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [289.826647] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [289.827215] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [289.827752] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [289.828584] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [289.829072] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [289.829683] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [289.830044] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [289.830049] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [289.830505] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [289.830703] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [289.831109] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [289.831343] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [289.831348] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [289.831530] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [289.835762] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [289.835768] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [289.836016] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [289.836264] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [289.836270] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [289.840539] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [289.840557] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [289.840561] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [289.841308] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [289.841788] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [289.842398] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [289.842428] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [289.842432] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [289.842876] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [289.843154] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [289.843565] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [289.843784] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [289.843789] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [289.844010] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [289.848270] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [289.848275] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [289.848473] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [289.848498] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [289.848503] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [289.852801] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [289.852845] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [289.852849] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [289.853687] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [289.854187] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [289.854780] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [289.854824] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [289.854829] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [289.855312] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [289.855501] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [289.855901] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [289.856153] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [289.856159] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [289.856353] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [289.860728] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [289.860733] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [289.860939] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [289.928117] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [289.928589] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [289.929055] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [289.929476] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [289.930366] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [300.917486] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [300.929565] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [300.953285] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [300.961105] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [300.963086] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [300.962625] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [300.963389] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [300.964085] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [300.964940] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [300.964846] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [300.969358] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [300.969966] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [300.971554] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [300.972611] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [300.974669] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [300.975376] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [300.975576] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [300.976003] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [300.976333] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [300.976341] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [300.976626] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [300.981263] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [300.981269] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [300.981647] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [300.983209] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [300.983457] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [300.983680] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [300.983898] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [300.984636] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [300.985123] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [300.989896] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [301.084687] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [301.103708] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:59:pipe A]
<7> [301.115043] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [301.124028] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [301.125043] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [301.125604] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [301.126367] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [301.127310] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:84:pipe B]
<7> [301.127198] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [301.131738] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [301.132347] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [301.133606] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [301.134521] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [301.135870] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [301.136351] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [301.136551] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [301.136973] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [301.137209] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [301.137215] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [301.137411] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [301.141563] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [301.141570] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [301.142015] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:109:pipe C]
<7> [301.145081] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [301.145310] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [301.145516] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [301.145717] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [301.146426] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [301.146659] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [301.149856] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [301.255124] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [301.267689] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [301.269240] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [301.269873] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [301.269862] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [301.270973] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [301.272858] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [301.275657] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [301.276173] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [301.277136] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [301.277909] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [301.279154] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [301.279631] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [301.279825] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [301.280236] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [301.280466] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [301.280472] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [301.280664] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [301.285172] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [301.285178] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [301.285539] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [301.286000] [IGT] kms_pm_rpm: exiting, ret=0
<6> [301.287330] Console: switching to colour frame buffer device 128x48
Created at 2026-04-04 03:50:30