igt@i915_module_load@load on fi-skl-6600u@next-20260401 Test details

Detail	Value
Duration	1.90 seconds
Igt-Version	IGT-Version: 2.4-gcb6666eae (x86_64) (Linux: 7.0.0-rc6-next-20260401-next-20260401-gbd0f139e5fc1+ x86_64)
Out	Using IGT_SRANDOM=1775056225 for randomisation Starting subtest: load Opened device: /dev/dri/card0 Subtest load: SUCCESS (1.895s)
Err	Starting subtest: load Subtest load: SUCCESS (1.895s)
Dmesg	<6> [41.752373] [IGT] i915_module_load: executing <4> [41.752503] NOTICE: Automounting of tracing to debugfs is deprecated and will be removed in 2030 <6> [41.769667] [IGT] i915_module_load: starting subtest load <4> [42.763177] <4> [42.763186] ******************************************************** <4> [42.763189] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [42.763191] <4> [42.763192] trace_printk() being used. Allocating extra memory. <4> [42.763194] <4> [42.763196] This means that this is a DEBUG kernel and it is <4> [42.763198] unsafe for production use. <4> [42.763200] <4> [42.763201] If you see this message and you are not debugging <4> [42.763203] the kernel, report this immediately to your vendor! <4> [42.763205] <4> [42.763207] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [42.763208] ******************************************************** <5> [42.788491] Setting dangerous option force_probe - tainting kernel <6> [42.807527] i915 0000:00:02.0: [drm] Found skylake/ult (device ID 1916) integrated display version 9.00 stepping H0 <7> [42.810151] i915 0000:00:02.0: [drm:intel_wopcm_init_early [i915]] WOPCM: 1024K <7> [42.810673] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no) <7> [42.811079] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint LP PCH <7> [42.811444] i915 0000:00:02.0: [drm:intel_dmc_wl_init [i915]] Sanitized enable_dmc_wl value: 0 (disabled) <7> [42.811786] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT <7> [42.812385] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing <7> [42.812666] i915 0000:00:02.0: [drm:intel_display_device_info_runtime_init [i915]] rawclk rate: 24000 kHz <7> [42.814798] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M <7> [42.815123] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M <7> [42.815356] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M <6> [42.815588] i915 0000:00:02.0: [drm] VT-d active for gfx access <6> [42.817339] i915 0000:00:02.0: vgaarb: deactivate vga console <6> [42.818458] i915 0000:00:02.0: [drm] Using Transparent Hugepages <7> [42.818505] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 7ff00047 <7> [42.818823] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K <7> [42.819155] i915 0000:00:02.0: [drm:intel_memory_regions_hw_probe [i915]] Memory region(0): system: 7715 MiB [mem 0x00000000-0x1e2394fff], io: n/a <7> [42.819440] i915 0000:00:02.0: [drm:intel_memory_regions_hw_probe [i915]] Memory region(5): stolen-system: 63 MiB [mem 0x7c000000-0x7fefffff], io: n/a <7> [42.820643] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x79ec6018 <7> [42.821076] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0 <7> [42.821391] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported <7> [42.821678] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x <7> [42.822059] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported <7> [42.831987] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483 <7> [42.832326] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported <7> [42.832602] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported <7> [42.832916] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4) <7> [42.833314] i915 0000:00:02.0: [drm:skl_dram_print_dimm_info.isra.0 [i915]] CH0 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb+ DIMMs: no <7> [42.833667] i915 0000:00:02.0: [drm:skl_dram_print_dimm_info.isra.0 [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb+ DIMMs: no <7> [42.833997] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb+ DIMMs: no <7> [42.834329] i915 0000:00:02.0: [drm:skl_dram_print_dimm_info.isra.0 [i915]] CH1 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb+ DIMMs: no <7> [42.834622] i915 0000:00:02.0: [drm:skl_dram_print_dimm_info.isra.0 [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb+ DIMMs: no <7> [42.834998] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb+ DIMMs: no <7> [42.835312] i915 0000:00:02.0: [drm:skl_dram_get_channels_info [i915]] Memory configuration is symmetric? yes <7> [42.835612] i915 0000:00:02.0: [drm:skl_dram_get_channels_info [i915]] 16Gb+ DIMMs: no <7> [42.835937] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM type: LPDDR3 <7> [42.836334] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2 <7> [42.836672] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] Num QGV points 0 <7> [42.837033] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] Num PSF GV points 0 <7> [42.838078] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz <7> [42.838462] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 203 <7> [42.838785] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7) <7> [42.839115] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5) <7> [42.839519] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100) <7> [42.839822] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19) <7> [42.840175] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 850) <7> [42.840533] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34) <7> [42.840912] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148) <7> [42.841263] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366) <7> [42.841560] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305) <7> [42.841877] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 136) <7> [42.842244] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0 <7> [42.842555] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2 <7> [42.842925] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806 <7> [42.843282] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6 <7> [42.843594] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6 <7> [42.843918] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping <7> [42.844299] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [42.844592] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0 <7> [42.844900] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [42.845247] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 8 <7> [42.845527] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [42.845808] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8 <7> [42.846124] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02 <7> [42.846483] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [42.846843] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [42.847194] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO <7> [42.847522] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 450000 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 1 <7> [42.847811] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz <7> [42.848150] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max dotclock rate: 675000 kHz <7> [42.848467] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [42.848823] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [42.849142] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [42.849432] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [42.849719] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [42.850433] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E <7> [42.850729] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B <7> [42.851030] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C <7> [42.851345] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D <7> [42.852381] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/skl_dmc_ver1_27.bin <7> [42.855097] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1 <7> [42.856446] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV <7> [42.857129] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us <7> [42.857562] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM0 latency not provided <7> [42.858050] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM1 latency 17 (17.0 usec) <7> [42.858467] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM2 latency 26 (26.0 usec) <7> [42.859517] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM3 latency 30 (30.0 usec) <7> [42.860115] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM4 latency 61 (61.0 usec) <7> [42.860532] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM5 latency 75 (75.0 usec) <7> [42.861107] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM6 latency 81 (81.0 usec) <7> [42.861488] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM7 latency 97 (97.0 usec) <7> [42.861901] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM0 latency 2 (2.0 usec) <7> [42.862303] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM1 latency 19 (19.0 usec) <7> [42.862715] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM2 latency 28 (28.0 usec) <7> [42.863149] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM3 latency 32 (32.0 usec) <7> [42.863564] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM4 latency 63 (63.0 usec) <7> [42.863617] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] DMC 0: <7> [42.864238] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] mmio[0]: 0x8f074 = 0x2fc0 <7> [42.864516] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM5 latency 77 (77.0 usec) <7> [42.864602] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] mmio[1]: 0x8f004 = 0xb40068 (EVT_HTP) <7> [42.864941] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM6 latency 83 (83.0 usec) <7> [42.865068] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] mmio[2]: 0x8f034 = 0xc003b400 (EVT_CTL) <7> [42.865342] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM7 latency 99 (99.0 usec) <6> [42.866277] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/skl_dmc_ver1_27.bin (v1.27) <7> [42.874609] i915 0000:00:02.0: [drm:intel_crtc_init [i915]] 3 display pipes available. <7> [42.879499] i915 0000:00:02.0: [drm:intel_cdclk_read_hw [i915]] Current CDCLK 450000 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 1 <7> [42.880533] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:110:DDI A/PHY A] Using AUX CH A (VBT) <7> [42.881315] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:110:DDI A/PHY A] <7> [42.891906] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0) <7> [42.892400] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2 <7> [42.892818] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2 <7> [42.893263] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless <7> [42.893703] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa <7> [42.894531] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel manufacturer name: MS_, product code: 3, serial number: 3, year of manufacture: 2002 <7> [42.895108] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: HD eDP <7> [42.895510] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz <7> [42.896076] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 10, level 255, controller 0 <7> [42.896370] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:0 <7> [42.896845] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:110:DDI A/PHY A] initial power sequencer: PPS 0 <7> [42.897309] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios power_up 0 backlight_on 0 backlight_off 0 power_down 500 power_cycle 5000 <7> [42.898093] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000 <7> [42.898503] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100 <7> [42.898816] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 500 <7> [42.899165] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [42.899513] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06 <7> [42.900284] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:110:DDI A/PHY A] PPS 0 turning VDD on <7> [42.900625] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:110:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000000f <7> [42.901629] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00 <7> [42.902251] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000 <7> [42.903476] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 9f 40 00 00 <7> [42.905315] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1 <7> [42.912021] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [42.912038] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD monitor <7> [42.912050] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD size 20, SAD count 0 <7> [42.912180] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:111:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa <7> [42.912491] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:111:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa <7> [42.912763] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:111:eDP-1] DRRS type: static <7> [42.913247] i915 0000:00:02.0: [drm:lpt_setup_backlight [i915]] [CONNECTOR:111:eDP-1] Using native PCH PWM for backlight control <7> [42.913568] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:111:eDP-1] backlight initialized, enabled, brightness 937/937 <7> [42.914149] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios power_up 0 backlight_on 0 backlight_off 0 power_down 500 power_cycle 5000 <7> [42.914437] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000 <7> [42.914704] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100 <7> [42.915058] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 500 <7> [42.915380] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [42.915704] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06 <7> [42.916465] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:118:DDI B/PHY B] Using AUX CH B (VBT) <7> [42.916809] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:118:DDI B/PHY B] <7> [42.917931] i915 0000:00:02.0: [drm:intel_psr_init [i915]] PSR condition failed: Port not supported <7> [42.918270] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:118:DDI B/PHY B] <7> [42.918555] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:118:DDI B/PHY B] Using DDC pin 0x5 (VBT) <7> [42.919640] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:133:DDI C/PHY C] Using AUX CH C (VBT) <7> [42.920046] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:133:DDI C/PHY C] <7> [42.920889] i915 0000:00:02.0: [drm:intel_psr_init [i915]] PSR condition failed: Port not supported <7> [42.921272] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:133:DDI C/PHY C] <7> [42.921599] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:133:DDI C/PHY C] Using DDC pin 0x4 (VBT) <7> [42.922600] i915 0000:00:02.0: [drm:intel_vga_disable [i915]] VGA plane is disabled <6> [42.922982] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io:owns=io+mem <7> [42.923519] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:59:pipe A] hw state readout: enabled <7> [42.924100] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:84:pipe B] hw state readout: disabled <7> [42.924545] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:109:pipe C] hw state readout: disabled <7> [42.925376] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:35:plane 1A] hw state readout: enabled, pipe A <7> [42.925735] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:44:plane 2A] hw state readout: disabled, pipe A <7> [42.926089] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:53:cursor A] hw state readout: disabled, pipe A <7> [42.926514] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 1B] hw state readout: disabled, pipe B <7> [42.926850] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:69:plane 2B] hw state readout: disabled, pipe B <7> [42.927226] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:78:cursor B] hw state readout: disabled, pipe B <7> [42.927592] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 1C] hw state readout: disabled, pipe C <7> [42.928023] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:plane 2C] hw state readout: disabled, pipe C <7> [42.928422] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:103:cursor C] hw state readout: disabled, pipe C <7> [42.928794] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp <7> [42.929370] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:110:DDI A/PHY A] hw state readout: enabled, pipe A <7> [42.929709] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:118:DDI B/PHY B] hw state readout: disabled, pipe A <7> [42.930027] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:120:DP-MST A] hw state readout: disabled, pipe A <7> [42.930398] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:121:DP-MST B] hw state readout: disabled, pipe B <7> [42.930691] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:122:DP-MST C] hw state readout: disabled, pipe C <7> [42.931086] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:133:DDI C/PHY C] hw state readout: disabled, pipe A <7> [42.931385] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:135:DP-MST A] hw state readout: disabled, pipe A <7> [42.931687] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:136:DP-MST B] hw state readout: disabled, pipe B <7> [42.932072] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:137:DP-MST C] hw state readout: disabled, pipe C <7> [42.932445] i915 0000:00:02.0: [drm:intel_dpll_crtc_get [i915]] [CRTC:59:pipe A] reserving DPLL 0 <7> [42.932745] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x1, on 1 <7> [42.933119] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [42.933528] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0 <7> [42.933843] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0 <7> [42.934406] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:111:eDP-1] hw state readout: enabled <7> [42.934821] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:119:DP-1] hw state readout: disabled <7> [42.935226] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:128:HDMI-A-1] hw state readout: disabled <7> [42.935603] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:134:DP-2] hw state readout: disabled <7> [42.936048] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:140:HDMI-A-2] hw state readout: disabled <7> [42.936629] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:35:plane 1A] min_cdclk 373250 kHz <7> [42.937010] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:44:plane 2A] min_cdclk 0 kHz <7> [42.937340] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:53:cursor A] min_cdclk 0 kHz <7> [42.937631] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:59:pipe A] min_cdclk 373250 kHz <7> [42.937939] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 1B] min_cdclk 0 kHz <7> [42.938320] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:69:plane 2B] min_cdclk 0 kHz <7> [42.938606] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:78:cursor B] min_cdclk 0 kHz <7> [42.938936] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:84:pipe B] min_cdclk 0 kHz <7> [42.939260] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 1C] min_cdclk 0 kHz <7> [42.939602] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:plane 2C] min_cdclk 0 kHz <7> [42.939911] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:103:cursor C] min_cdclk 0 kHz <7> [42.940242] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:109:pipe C] min_cdclk 0 kHz <7> [42.940554] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:59:pipe A] dbuf slices 0x1, ddb (0 - 446), active pipes 0x1, mbus joined: no <7> [42.940874] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:84:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7> [42.941206] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:109:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7> [42.942221] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:59:pipe A] enable: yes [setup_hw_state] <7> [42.942534] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [42.942813] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0 <7> [42.943198] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [42.943526] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [42.943815] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0 <7> [42.944112] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [42.944498] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m_n: lanes: 4; data_m: 4348677, data_n: 8388608, link_m: 362389, link_n: 524288, tu: 64 <7> [42.944783] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [42.945104] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: enabled <7> [42.945425] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sdp split: disabled <7> [42.945782] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled <7> [42.946103] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] minimum hblank: 0 <7> [42.946431] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0 <7> [42.946709] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] scanline offset: 1 <7> [42.947085] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0, set context latency: 0 <7> [42.947438] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, fixed rr: no, vmin: 0, vmax: 0, flipline: 0, pipeline full: 0, guardband: 0 vsync start: 0, vsync end: 0 <7> [42.947745] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: vmin vblank: 0, vmax vblank: 0, vmin vtotal: 0, vmax vtotal: 0 <7> [42.948095] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0 <7> [42.948449] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa <7> [42.948756] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa <7> [42.949061] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa <7> [42.949397] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa <7> [42.949779] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa <7> [42.950131] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pixel rate 373250, min cdclk 373250, min voltage level 0 <7> [42.950471] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 73, ips linetime: 0 <7> [42.950747] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [42.951128] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe src: 3200x1800+0+0 <7> [42.951422] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [42.951699] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7> [42.951998] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [42.952367] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: ctrl1: 0x1, cfgcr1: 0x0, cfgcr2: 0x0 <7> [42.952641] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [42.952938] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [42.953250] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [42.953585] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [42.953879] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [42.954189] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [42.954454] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [42.954782] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:84:pipe B] enable: no [setup_hw_state] <7> [42.955106] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:109:pipe C] enable: no [setup_hw_state] <7> [42.955635] i915 0000:00:02.0: [drm:skl_get_initial_plane_config [i915]] [CRTC:59:pipe A][PLANE:35:plane 1A] with fb: size=3200x1800@32, offset=0, pitch 12800, size 0x15f9000 <7> [42.955995] i915 0000:00:02.0: [drm:initial_plane_vma [i915]] Using dma_addr=0x000000007c000000, based on initial plane programming <7> [42.956302] i915 0000:00:02.0: [drm:_i915_gem_object_stolen_init [i915]] creating preallocated stolen object: stolen_offset=0x0000000000000000, size=0x00000000015f9000 <7> [42.958294] i915 0000:00:02.0: [drm:initial_plane_vma [i915]] Initial plane fb bound to 0x0 in the ggtt (original 0x0) <7> [42.959013] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[15f9000, 15fb000] for use by error capture <7> [42.959318] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [15fb000, 100000000] <7> [42.959650] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0 <7> [42.959981] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 5 GT workarounds on global <7> [42.961657] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 8 engine workarounds on rcs'0 <7> [42.961988] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 5 whitelist workarounds on rcs'0 <7> [42.962273] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 12 context workarounds on rcs'0 <7> [42.989522] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed rcs'0 to rcs0 <7> [42.989813] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed bcs'0 to bcs0 <7> [42.990162] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed vcs'0 to vcs0 <7> [42.990447] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed vecs'0 to vecs0 <7> [42.990763] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:59:pipe A] FQ 0: start 0x8 <7> [42.991094] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:59:pipe A] FQ 1: start 0x108 <7> [42.991413] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:59:pipe A] FQ 2: start 0x208 <7> [42.991689] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:59:pipe A] FQ 3: start 0x308 <7> [42.992050] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:59:pipe A] FQ 4: start 0x3c8 <7> [42.992350] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:84:pipe B] FQ 0: start 0x8 <7> [42.992639] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:84:pipe B] FQ 1: start 0x108 <7> [42.992940] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:84:pipe B] FQ 2: start 0x208 <7> [42.993273] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:84:pipe B] FQ 3: start 0x308 <7> [42.993557] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:84:pipe B] FQ 4: start 0x3c8 <7> [42.994211] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:109:pipe C] FQ 0: start 0x8 <7> [42.994583] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:109:pipe C] FQ 1: start 0x108 <7> [42.994900] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:109:pipe C] FQ 2: start 0x208 <7> [42.995253] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:109:pipe C] FQ 3: start 0x308 <7> [42.995583] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:109:pipe C] FQ 4: start 0x3c8 <7> [42.996326] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:59:pipe A] dbuf slices 0x1 -> 0x1, ddb (0 - 446) -> (0 - 892), active pipes 0x1 -> 0x1 <7> [42.996914] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:59:pipe A] dbuf slices 0x1 -> 0x1, ddb (0 - 446) -> (0 - 892), active pipes 0x1 -> 0x1 <7> [42.997258] i915 0000:00:02.0: [drm:skl_print_plane_ddb_changes [i915]] [PLANE:35:plane 1A] ddb ( 0 - 446) -> ( 0 - 856), size 446 -> 856 <7> [42.997555] i915 0000:00:02.0: [drm:skl_print_plane_ddb_changes [i915]] [PLANE:53:cursor A] ddb ( 0 - 0) -> ( 856 - 892), size 0 -> 36 <7> [42.998272] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5,wm6,*wm7, twm, swm, stwm <7> [42.998635] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 <7> [42.998966] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 7, 58, 84, 96, 184, 227, 245, 288, 0, 0, 0 <7> [42.999332] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 8, 59, 85, 97, 185, 228, 246, 289, 0, 0, 0 <7> [42.999645] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] min_ddb_uv 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [43.000019] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:84:pipe B] enable: no [fastset] <7> [43.000332] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:109:pipe C] enable: no [fastset] <7> [43.014580] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:84:pipe B] <7> [43.015114] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:109:pipe C] <7> [43.024203] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:111:eDP-1] adding connector to sysfs <7> [43.028759] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:111:eDP-1] backlight device intel_backlight registered <7> [43.029404] i915 0000:00:02.0: [drm:intel_panel_register [i915]] [CONNECTOR:111:eDP-1] Registered panel device 'card0-eDP-1', has fwnode: yes <7> [43.029840] i915 0000:00:02.0: [drm:intel_panel_register [i915]] [CONNECTOR:111:eDP-1] Panel prepare <7> [43.031618] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1 <7> [43.036418] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:111:eDP-1] generating connector hotplug event <7> [43.036618] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:119:DP-1] adding connector to sysfs <7> [43.038241] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1 <7> [43.041333] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:119:DP-1] generating connector hotplug event <7> [43.041479] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:128:HDMI-A-1] adding connector to sysfs <7> [43.042702] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:128:HDMI-A-1] generating connector hotplug event <7> [43.043378] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:134:DP-2] adding connector to sysfs <7> [43.045514] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DDI C/PHY C bus for card0-DP-2 <7> [43.049324] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:134:DP-2] generating connector hotplug event <7> [43.049502] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:140:HDMI-A-2] adding connector to sysfs <7> [43.051660] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:140:HDMI-A-2] generating connector hotplug event <6> [43.055928] [drm] Initialized i915 1.6.0 for 0000:00:02.0 on minor 0 <7> [43.062198] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 5 outputs detected <6> [43.114979] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6> [43.132305] input: Video Bus as /devices/pci0000:00/acpi.video_bus.0/input/input23 <7> [43.141756] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10) <7> [43.146013] check_position_fix: snd_hda_intel 0000:00:1f.3: Using SKL position fix <6> [43.146027] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4 <7> [43.147474] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-1] <7> [43.148817] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] found possible fb from [PLANE:35:plane 1A] <7> [43.150158] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:84:pipe B] not active, skipping <7> [43.150631] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:109:pipe C] not active, skipping <7> [43.151100] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] checking [PLANE:35:plane 1A] for BIOS fb <7> [43.151518] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:59:pipe A] area: 3200x1800, bpp: 32, size: 23040000 <7> [43.151983] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] fb big enough [PLANE:35:plane 1A] (23040000 >= 23040000) <7> [43.152417] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:84:pipe B] not active, skipping <7> [43.152826] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:109:pipe C] not active, skipping <7> [43.153922] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:119:DP-1] status updated from unknown to disconnected (epoch counter 0->1) <7> [43.154634] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1] <7> [43.156160] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [43.156619] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [43.156904] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] using BIOS fb for initial console <7> [43.157261] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [43.157697] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [43.158680] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [43.158694] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [43.159146] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [43.159698] i915 0000:00:02.0: [drm:drm_client_modeset_probe] <7> [43.162763] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [43.162779] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [43.163467] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:128:HDMI-A-1] status updated from unknown to disconnected (epoch counter 0->1) <7> [43.164284] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-2] <7> [43.169650] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:134:DP-2] status updated from unknown to disconnected (epoch counter 0->1) <7> [43.170434] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:140:HDMI-A-2] <7> [43.172603] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [43.174640] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [43.175349] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [43.175822] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [43.175835] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [43.176251] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [43.182395] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [43.182413] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [43.184216] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:140:HDMI-A-2] status updated from unknown to disconnected (epoch counter 0->1) <7> [43.186516] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event <7> [43.186588] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1] <7> [43.186609] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:eDP-1] <7> [43.191207] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [43.191561] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [43.192749] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [43.194573] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [43.194588] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD monitor <7> [43.194604] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD size 20, SAD count 0 <7> [43.194672] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] VRR capable: no <7> [43.195529] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [43.196016] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no <7> [43.198767] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1] status updated from unknown to connected <7> [43.199440] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event <7> [43.201885] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1] probed modes: <7> [43.201908] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa <7> [43.201921] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa <7> [43.201940] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-1] <7> [43.201952] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-1] <7> [43.206729] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-1] disconnected <7> [43.206753] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] <7> [43.206767] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1] <7> [43.207911] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [43.208339] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [43.210562] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [43.212837] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [43.212875] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [43.213353] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [43.217251] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [43.217266] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [43.217765] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected <7> [43.221313] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-2] <7> [43.221330] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-2] <7> [43.225970] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-2] disconnected <7> [43.225993] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:140:HDMI-A-2] <7> [43.226007] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:140:HDMI-A-2] <7> [43.226790] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [43.227255] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [43.227875] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [43.228371] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [43.228383] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [43.228785] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [43.232599] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [43.232613] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [43.233182] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:140:HDMI-A-2] disconnected <7> [43.233197] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:eDP-1] enabled? yes <7> [43.233259] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:119:DP-1] enabled? no <7> [43.233268] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:128:HDMI-A-1] enabled? no <7> [43.233277] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:134:DP-2] enabled? no <7> [43.233285] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:140:HDMI-A-2] enabled? no <7> [43.233694] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [43.233753] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:eDP-1] found preferred mode: 3200x1800 <7> [43.233764] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [43.234339] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:59:pipe A] desired mode 3200x1800 set (0,0) <6> [43.235497] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops intel_audio_component_bind_ops [i915]) <7> [43.237088] i915 0000:00:02.0: [drm:intel_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10 <7> [43.237591] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <7> [43.238657] i915 0000:00:02.0: [drm:intel_fbdev_driver_fbdev_probe [i915]] re-using BIOS fb <7> [43.242365] i915 0000:00:02.0: [drm:intel_fbdev_driver_fbdev_probe [i915]] allocated 3200x1800 fb <7> [43.244283] azx_first_init: snd_hda_intel 0000:00:1f.3: chipset global capabilities = 0x9701 <7> [43.251048] azx_init_pci: snd_hda_intel 0000:00:1f.3: Clearing TCSEL <7> [43.251067] azx_init_pci: snd_hda_intel 0000:00:1f.3: SCH snoop: Enabled <6> [43.259521] fbcon: i915drmfb (fb0) is primary device <7> [43.269837] i915 0000:00:02.0: [drm:intel_backlight_device_update_status [i915]] updating intel_backlight, brightness=46/937 <7> [43.273815] i915 0000:00:02.0: [drm:intel_panel_actually_set_backlight [i915]] [CONNECTOR:111:eDP-1] set backlight level = 81 <7> [43.280844] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:111:eDP-1] Limiting target display pipe bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36) <7> [43.283265] i915 0000:00:02.0: [drm:intel_dp_compute_config_limits [i915]] [ENCODER:110:DDI A/PHY A][CRTC:59:pipe A] DP link limits: pixel clock 373250 kHz DSC off max lanes 4 max rate 540000 max pipe_bpp 24 min link_bpp 18.0000 max link_bpp 24.0000 <7> [43.283676] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp input 24 compressed 0.0000 HDR no link rate required 1119750 available 2160000 <7> [43.284124] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:59:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0 <7> [43.284554] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:110:DDI A/PHY A] [CRTC:59:pipe A] <7> [43.285065] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:44:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [43.285454] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:44:plane 2A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [43.286581] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:44:plane 2A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [43.288604] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:44:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [43.289120] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:44:plane 2A] min_ddb_uv 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [43.289553] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:53:cursor A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [43.290022] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:53:cursor A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [43.290437] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:53:cursor A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [43.290845] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:53:cursor A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [43.291277] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:53:cursor A] min_ddb_uv 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [43.291776] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:59:pipe A] enable: yes [fastset] <7> [43.292249] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [43.292687] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0 <7> [43.293149] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [43.293586] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [43.296175] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0 <7> [43.296664] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [43.297220] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m_n: lanes: 4; data_m: 4348677, data_n: 8388608, link_m: 362389, link_n: 524288, tu: 64 <7> [43.297649] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [43.298095] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: enabled <7> [43.298510] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sdp split: disabled <7> [43.298948] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled <7> [43.299378] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] minimum hblank: 0 <7> [43.299798] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [43.300258] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] DP SDP: VSC, revision 2, length 8 <7> [43.300687] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pixelformat: RGB <7> [43.301468] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] colorimetry: sRGB <7> [43.302107] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bpc: 0 <7> [43.302537] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dynamic range: VESA range <7> [43.302994] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] content type: Not defined <7> [43.303429] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] scanline offset: 1 <7> [43.303843] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0, set context latency: 0 <7> [43.304297] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, fixed rr: no, vmin: 0, vmax: 0, flipline: 0, pipeline full: 0, guardband: 0 vsync start: 0, vsync end: 0 <7> [43.304721] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: vmin vblank: 0, vmax vblank: 0, vmin vtotal: 0, vmax vtotal: 0 <7> [43.307306] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0 <7> [43.307796] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa <7> [43.308267] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa <7> [43.308691] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa <7> [43.309187] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa <7> [43.309672] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa <7> [43.310126] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pixel rate 373250, min cdclk 373250, min voltage level 0 <7> [43.310555] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 73, ips linetime: 0 <7> [43.310994] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [43.311409] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe src: 3200x1800+0+0 <7> [43.311825] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [43.312278] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0 <7> [43.312693] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [43.313148] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: ctrl1: 0x1, cfgcr1: 0x0, cfgcr2: 0x0 <7> [43.313518] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x2 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [43.313817] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [43.314148] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [43.314444] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [43.314736] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [43.315055] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [43.315354] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [43.315655] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:35:plane 1A] fb: [FB:144] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7> [43.316036] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7> [43.316404] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0 <7> [43.316704] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:44:plane 2A] fb: [NOFB], visible: no <7> [43.317114] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:53:cursor A] fb: [NOFB], visible: no <7> [43.331753] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1 <7> [43.336721] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:111:eDP-1] <7> [43.337401] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:59:pipe A] <7> [43.341275] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV <6> [43.343323] Console: switching to colour frame buffer device 200x56 <7> [43.366633] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port B <7> [43.367552] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port B <7> [43.368412] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port B <7> [43.368828] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port C <7> [43.369259] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port C <7> [43.369687] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port C <7> [43.370127] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port D <7> [43.370532] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port D <7> [43.371000] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port D <6> [43.373841] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device <7> [43.373895] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: display version: 9 <7> [43.374401] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: display stepping: H0 <7> [43.374815] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: cursor_needs_physical: no <7> [43.375617] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_cdclk_crawl: no <7> [43.376399] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_cdclk_squash: no <7> [43.377053] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_ddi: yes <7> [43.377456] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dp_mst: yes <7> [43.377821] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dsb: no <7> [43.378482] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_fpga_dbg: yes <7> [43.379094] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_gmch: no <7> [43.379531] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hotplug: yes <7> [43.380153] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hti: no <7> [43.380590] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_ipc: yes <7> [43.382898] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_overlay: no <7> [43.383307] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_psr: yes <7> [43.383707] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_psr_hw_tracking: yes <7> [43.384693] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: overlay_needs_physical: no <7> [43.385092] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: supports_tv: no <7> [43.385507] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hdcp: yes <7> [43.386081] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dmc: yes <7> [43.386501] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dsc: no <7> [43.386945] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: rawclk rate: 24000 kHz <7> [43.388621] [drm:intel_dsm_detect.isra.0 [i915]] no _DSM method for intel device <7> [43.391926] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D <7> [43.392713] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C <7> [43.393158] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B <7> [43.393665] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: pciid=0x1916 rev=0x07 platform=SKYLAKE (subplatform=0x1) gen=9 <7> [43.394046] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: graphics version: 9 <7> [43.394382] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: media version: 9 <7> [43.394731] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: graphics stepping: H0 <7> [43.395274] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: media stepping: H0 <7> [43.395617] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: gt: 2 <7> [43.395987] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: memory-regions: 0x21 <7> [43.396322] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: page-sizes: 0x11000 <7> [43.396656] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: platform: SKYLAKE <7> [43.397089] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: ppgtt-size: 48 <7> [43.397436] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: ppgtt-type: 2 <7> [43.397773] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: dma_mask_size: 39 <7> [43.398318] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: is_mobile: no <7> [43.398659] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: require_force_probe: no <7> [43.398939] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: is_dgfx: no <7> [43.399252] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_64bit_reloc: yes <7> [43.399581] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_64k_pages: no <7> [43.399919] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: gpu_reset_clobbers_display: no <7> [43.400226] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_reset_engine: yes <7> [43.400562] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_3d_pipeline: yes <7> [43.400917] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_flat_ccs: no <7> [43.401248] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_global_mocs: no <7> [43.401563] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_gmd_id: no <7> [43.401903] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_gt_uc: yes <7> [43.402228] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_heci_pxp: no <7> [43.402550] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_heci_gscfi: no <7> [43.402895] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_guc_deprivilege: no <7> [43.403173] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_guc_tlb_invalidation: no <7> [43.403441] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_l3_ccs_read: no <7> [43.403672] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_l3_dpf: no <7> [43.403982] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_llc: yes <7> [43.404294] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_logical_ring_contexts: yes <7> [43.404519] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_logical_ring_elsq: no <7> [43.404746] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_media_ratio_mode: no <7> [43.404997] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_mslice_steering: no <7> [43.405272] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oa_bpc_reporting: no <7> [43.405506] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oa_slice_contrib_limits: no <7> [43.405741] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oam: no <7> [43.406022] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_one_eu_per_fuse_bit: no <7> [43.406342] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_pxp: no <7> [43.406611] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rc6: yes <7> [43.406846] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rc6p: no <7> [43.407108] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rps: yes <7> [43.407381] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_runtime_pm: yes <7> [43.407606] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_snoop: no <7> [43.407830] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_coherent_ggtt: yes <7> [43.408159] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: tuning_thread_rr_after_dep: no <7> [43.408487] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: unfenced_needs_alignment: no <7> [43.408765] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: hws_needs_physical: no <7> [43.409026] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_pooled_eu: no <7> [43.409328] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: iommu: enabled <7> [43.409658] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: available engines: 40403 <7> [43.410006] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice total: 1, mask=0001 <7> [43.410345] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: subslice total: 3 <7> [43.410672] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice0: 3 subslices, mask=00000007 <7> [43.411008] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice1: 0 subslices, mask=00000000 <7> [43.411329] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice2: 0 subslices, mask=00000000 <7> [43.411595] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: EU total: 24 <7> [43.411825] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: EU per subslice: 8 <7> [43.412164] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has slice power gating: no <7> [43.412485] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has subslice power gating: no <7> [43.412746] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has EU power gating: yes <6> [43.413276] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled <6> [43.413279] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled <6> [43.413282] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled <6> [43.421238] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input24 <7> [43.427651] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event] <7> [43.427677] i915 0000:00:02.0: [drm:drm_client_modeset_probe] <7> [43.428364] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1] <7> [43.428390] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:eDP-1] <7> [43.429102] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [43.432199] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [43.432617] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [43.433319] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [43.433331] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD monitor <7> [43.433356] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD size 20, SAD count 0 <7> [43.433434] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] VRR capable: no <7> [43.433825] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [43.435438] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no <7> [43.441197] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1] probed modes: <7> [43.441243] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa <7> [43.441254] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa <7> [43.441267] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-1] <7> [43.441279] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-1] <7> [43.446102] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-1] disconnected <7> [43.446124] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] <7> [43.446144] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1] <7> [43.447277] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [43.447692] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [43.448746] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [43.449487] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [43.449499] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [43.450819] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [43.457592] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [43.457605] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [43.458052] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected <7> [43.458068] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-2] <7> [43.458080] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-2] <7> [43.463425] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-2] disconnected <7> [43.463446] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:140:HDMI-A-2] <7> [43.463464] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:140:HDMI-A-2] <7> [43.464194] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [43.464583] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [43.465173] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [43.468985] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [43.469014] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [43.469422] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [43.476943] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [43.476959] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [43.477284] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:140:HDMI-A-2] disconnected <7> [43.477295] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:eDP-1] enabled? yes <7> [43.477302] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:119:DP-1] enabled? no <7> [43.477307] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:128:HDMI-A-1] enabled? no <7> [43.477312] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:134:DP-2] enabled? no <7> [43.477317] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:140:HDMI-A-2] enabled? no <7> [43.477565] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [43.477604] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:eDP-1] found preferred mode: 3200x1800 <7> [43.477610] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config <7> [43.477670] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:59:pipe A] desired mode 3200x1800 set (0,0) <6> [43.486668] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input25 <6> [43.490337] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input26 <7> [43.499998] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0 <7> [43.500663] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event] <7> [43.500681] i915 0000:00:02.0: [drm:drm_client_modeset_probe] <7> [43.501243] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1] <7> [43.501263] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:eDP-1] <7> [43.501817] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [43.503260] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [43.503691] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [43.505737] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [43.505751] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD monitor <7> [43.505771] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD size 20, SAD count 0 <7> [43.505832] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] VRR capable: no <7> [43.506235] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [43.506535] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no <7> [43.508729] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1] probed modes: <7> [43.508748] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa <7> [43.508756] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa <7> [43.508766] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-1] <7> [43.508773] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-1] <7> [43.513940] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-1] disconnected <7> [43.513963] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] <7> [43.513976] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1] <7> [43.515206] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [43.515596] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [43.516763] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [43.517236] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [43.517249] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [43.517602] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [43.521877] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [43.521894] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [43.522367] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected <7> [43.522385] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-2] <7> [43.522398] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-2] <7> [43.524934] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [43.526964] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-2] disconnected <7> [43.526986] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:140:HDMI-A-2] <7> [43.526999] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:140:HDMI-A-2] <7> [43.527668] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [43.529428] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [43.530365] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [43.530774] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [43.530787] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [43.531220] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [43.531337] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [43.535532] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [43.535550] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [43.536187] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:140:HDMI-A-2] disconnected <7> [43.536204] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:eDP-1] enabled? yes <7> [43.536215] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:119:DP-1] enabled? no <7> [43.536224] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:128:HDMI-A-1] enabled? no <7> [43.536232] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:134:DP-2] enabled? no <7> [43.536239] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:140:HDMI-A-2] enabled? no <7> [43.536503] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [43.536559] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:eDP-1] found preferred mode: 3200x1800 <7> [43.536569] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config <7> [43.536663] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:59:pipe A] desired mode 3200x1800 set (0,0) <7> [43.553503] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0 <7> [43.599657] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [43.600038] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [43.664558] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <6> [43.665001] [IGT] i915_module_load: finished subtest load, SUCCESS <6> [43.665402] [IGT] i915_module_load: exiting, ret=0

<4> [41.752503] NOTICE: Automounting of tracing to debugfs is deprecated and will be removed in 2030

<6> [41.769667] [IGT] i915_module_load: starting subtest load

<4> [42.763186] **********************************************************

<4> [42.763189] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [42.763192] ** trace_printk() being used. Allocating extra memory. **

<4> [42.763196] ** This means that this is a DEBUG kernel and it is **

<4> [42.763201] ** If you see this message and you are not debugging **

<4> [42.763203] ** the kernel, report this immediately to your vendor! **

<4> [42.763207] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [42.763208] **********************************************************

<5> [42.788491] Setting dangerous option force_probe - tainting kernel

<6> [42.807527] i915 0000:00:02.0: [drm] Found skylake/ult (device ID 1916) integrated display version 9.00 stepping H0

<7> [42.810151] i915 0000:00:02.0: [drm:intel_wopcm_init_early [i915]] WOPCM: 1024K

<7> [42.810673] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)

<7> [42.811079] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint LP PCH

<7> [42.811444] i915 0000:00:02.0: [drm:intel_dmc_wl_init [i915]] Sanitized enable_dmc_wl value: 0 (disabled)

<7> [42.811786] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT

<7> [42.812385] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing

<7> [42.812666] i915 0000:00:02.0: [drm:intel_display_device_info_runtime_init [i915]] rawclk rate: 24000 kHz

<7> [42.814798] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M

<7> [42.815123] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M

<7> [42.815356] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M

<6> [42.815588] i915 0000:00:02.0: [drm] VT-d active for gfx access

<6> [42.817339] i915 0000:00:02.0: vgaarb: deactivate vga console

<6> [42.818458] i915 0000:00:02.0: [drm] Using Transparent Hugepages

<7> [42.818505] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 7ff00047

<7> [42.818823] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K

<7> [42.819155] i915 0000:00:02.0: [drm:intel_memory_regions_hw_probe [i915]] Memory region(0): system: 7715 MiB [mem 0x00000000-0x1e2394fff], io: n/a

<7> [42.819440] i915 0000:00:02.0: [drm:intel_memory_regions_hw_probe [i915]] Memory region(5): stolen-system: 63 MiB [mem 0x7c000000-0x7fefffff], io: n/a

<7> [42.820643] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x79ec6018

<7> [42.821076] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0

<7> [42.821391] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported

<7> [42.821678] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x

<7> [42.822059] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported

<7> [42.831987] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483

<7> [42.832326] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported

<7> [42.832602] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported

<7> [42.832916] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)

<7> [42.833314] i915 0000:00:02.0: [drm:skl_dram_print_dimm_info.isra.0 [i915]] CH0 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb+ DIMMs: no

<7> [42.833667] i915 0000:00:02.0: [drm:skl_dram_print_dimm_info.isra.0 [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb+ DIMMs: no

<7> [42.833997] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb+ DIMMs: no

<7> [42.834329] i915 0000:00:02.0: [drm:skl_dram_print_dimm_info.isra.0 [i915]] CH1 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb+ DIMMs: no

<7> [42.834622] i915 0000:00:02.0: [drm:skl_dram_print_dimm_info.isra.0 [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb+ DIMMs: no

<7> [42.834998] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb+ DIMMs: no

<7> [42.835312] i915 0000:00:02.0: [drm:skl_dram_get_channels_info [i915]] Memory configuration is symmetric? yes

<7> [42.835612] i915 0000:00:02.0: [drm:skl_dram_get_channels_info [i915]] 16Gb+ DIMMs: no

<7> [42.835937] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM type: LPDDR3

<7> [42.836334] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2

<7> [42.836672] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] Num QGV points 0

<7> [42.837033] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] Num PSF GV points 0

<7> [42.838078] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz

<7> [42.838462] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 203

<7> [42.838785] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)

<7> [42.839115] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)

<7> [42.839519] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)

<7> [42.839822] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)

<7> [42.840175] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 850)

<7> [42.840533] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)

<7> [42.840912] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)

<7> [42.841263] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)

<7> [42.841560] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)

<7> [42.841877] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 136)

<7> [42.842244] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0

<7> [42.842555] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2

<7> [42.842925] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806

<7> [42.843282] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6

<7> [42.843594] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6

<7> [42.843918] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping

<7> [42.844299] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [42.844592] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0

<7> [42.844900] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [42.845247] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 8

<7> [42.845527] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [42.845808] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8

<7> [42.846124] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02

<7> [42.846483] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [42.846843] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [42.847194] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO

<7> [42.847522] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 450000 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 1

<7> [42.847811] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz

<7> [42.848150] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max dotclock rate: 675000 kHz

<7> [42.848467] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [42.848823] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [42.849142] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [42.849432] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [42.849719] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [42.850433] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E

<7> [42.850729] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B

<7> [42.851030] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C

<7> [42.851345] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D

<7> [42.852381] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/skl_dmc_ver1_27.bin

<7> [42.855097] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1

<7> [42.856446] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV

<7> [42.857129] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us

<7> [42.857562] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM0 latency not provided

<7> [42.858050] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM1 latency 17 (17.0 usec)

<7> [42.858467] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM2 latency 26 (26.0 usec)

<7> [42.859517] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM3 latency 30 (30.0 usec)

<7> [42.860115] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM4 latency 61 (61.0 usec)

<7> [42.860532] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM5 latency 75 (75.0 usec)

<7> [42.861107] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM6 latency 81 (81.0 usec)

<7> [42.861488] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] original WM7 latency 97 (97.0 usec)

<7> [42.861901] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM0 latency 2 (2.0 usec)

<7> [42.862303] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM1 latency 19 (19.0 usec)

<7> [42.862715] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM2 latency 28 (28.0 usec)

<7> [42.863149] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM3 latency 32 (32.0 usec)

<7> [42.863564] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM4 latency 63 (63.0 usec)

<7> [42.863617] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] DMC 0:

<7> [42.864238] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] mmio[0]: 0x8f074 = 0x2fc0

<7> [42.864516] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM5 latency 77 (77.0 usec)

<7> [42.864602] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] mmio[1]: 0x8f004 = 0xb40068 (EVT_HTP)

<7> [42.864941] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM6 latency 83 (83.0 usec)

<7> [42.865068] i915 0000:00:02.0: [drm:dmc_load_work_fn [i915]] mmio[2]: 0x8f034 = 0xc003b400 (EVT_CTL)

<7> [42.865342] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] adjusted WM7 latency 99 (99.0 usec)

<6> [42.866277] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/skl_dmc_ver1_27.bin (v1.27)

<7> [42.874609] i915 0000:00:02.0: [drm:intel_crtc_init [i915]] 3 display pipes available.

<7> [42.879499] i915 0000:00:02.0: [drm:intel_cdclk_read_hw [i915]] Current CDCLK 450000 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 1

<7> [42.880533] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:110:DDI A/PHY A] Using AUX CH A (VBT)

<7> [42.881315] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:110:DDI A/PHY A]

<7> [42.891906] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)

<7> [42.892400] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2

<7> [42.892818] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2

<7> [42.893263] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless

<7> [42.893703] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa

<7> [42.894531] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel manufacturer name: MS_, product code: 3, serial number: 3, year of manufacture: 2002

<7> [42.895108] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: HD eDP

<7> [42.895510] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz

<7> [42.896076] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 10, level 255, controller 0

<7> [42.896370] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:0

<7> [42.896845] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:110:DDI A/PHY A] initial power sequencer: PPS 0

<7> [42.897309] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios power_up 0 backlight_on 0 backlight_off 0 power_down 500 power_cycle 5000

<7> [42.898093] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000

<7> [42.898503] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100

<7> [42.898816] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 500

<7> [42.899165] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200

<7> [42.899513] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06

<7> [42.900284] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:110:DDI A/PHY A] PPS 0 turning VDD on

<7> [42.900625] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:110:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000000f

<7> [42.901629] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00

<7> [42.902251] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000

<7> [42.903476] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 9f 40 00 00

<7> [42.905315] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1

<7> [42.912021] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.

<7> [42.912038] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD monitor

<7> [42.912050] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD size 20, SAD count 0

<7> [42.912180] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:111:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa

<7> [42.912491] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:111:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa

<7> [42.912763] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:111:eDP-1] DRRS type: static

<7> [42.913247] i915 0000:00:02.0: [drm:lpt_setup_backlight [i915]] [CONNECTOR:111:eDP-1] Using native PCH PWM for backlight control

<7> [42.913568] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:111:eDP-1] backlight initialized, enabled, brightness 937/937

<7> [42.914149] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios power_up 0 backlight_on 0 backlight_off 0 power_down 500 power_cycle 5000

<7> [42.914437] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt power_up 2000 backlight_on 10 backlight_off 2000 power_down 500 power_cycle 5000

<7> [42.914704] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec power_up 2100 backlight_on 500 backlight_off 500 power_down 5000 power_cycle 5100

<7> [42.915058] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 500

<7> [42.915380] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200

<7> [42.915704] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06

<7> [42.916465] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:118:DDI B/PHY B] Using AUX CH B (VBT)

<7> [42.916809] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:118:DDI B/PHY B]

<7> [42.917931] i915 0000:00:02.0: [drm:intel_psr_init [i915]] PSR condition failed: Port not supported

<7> [42.918270] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:118:DDI B/PHY B]

<7> [42.918555] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:118:DDI B/PHY B] Using DDC pin 0x5 (VBT)

<7> [42.919640] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:133:DDI C/PHY C] Using AUX CH C (VBT)

<7> [42.920046] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:133:DDI C/PHY C]

<7> [42.920889] i915 0000:00:02.0: [drm:intel_psr_init [i915]] PSR condition failed: Port not supported

<7> [42.921272] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:133:DDI C/PHY C]

<7> [42.921599] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:133:DDI C/PHY C] Using DDC pin 0x4 (VBT)

<7> [42.922600] i915 0000:00:02.0: [drm:intel_vga_disable [i915]] VGA plane is disabled

<6> [42.922982] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io:owns=io+mem

<7> [42.923519] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:59:pipe A] hw state readout: enabled

<7> [42.924100] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:84:pipe B] hw state readout: disabled

<7> [42.924545] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:109:pipe C] hw state readout: disabled

<7> [42.925376] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:35:plane 1A] hw state readout: enabled, pipe A

<7> [42.925735] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:44:plane 2A] hw state readout: disabled, pipe A

<7> [42.926089] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:53:cursor A] hw state readout: disabled, pipe A

<7> [42.926514] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 1B] hw state readout: disabled, pipe B

<7> [42.926850] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:69:plane 2B] hw state readout: disabled, pipe B

<7> [42.927226] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:78:cursor B] hw state readout: disabled, pipe B

<7> [42.927592] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 1C] hw state readout: disabled, pipe C

<7> [42.928023] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:plane 2C] hw state readout: disabled, pipe C

<7> [42.928422] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:103:cursor C] hw state readout: disabled, pipe C

<7> [42.928794] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp

<7> [42.929370] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:110:DDI A/PHY A] hw state readout: enabled, pipe A

<7> [42.929709] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:118:DDI B/PHY B] hw state readout: disabled, pipe A

<7> [42.930027] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:120:DP-MST A] hw state readout: disabled, pipe A

<7> [42.930398] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:121:DP-MST B] hw state readout: disabled, pipe B

<7> [42.930691] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:122:DP-MST C] hw state readout: disabled, pipe C

<7> [42.931086] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:133:DDI C/PHY C] hw state readout: disabled, pipe A

<7> [42.931385] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:135:DP-MST A] hw state readout: disabled, pipe A

<7> [42.931687] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:136:DP-MST B] hw state readout: disabled, pipe B

<7> [42.932072] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:137:DP-MST C] hw state readout: disabled, pipe C

<7> [42.932445] i915 0000:00:02.0: [drm:intel_dpll_crtc_get [i915]] [CRTC:59:pipe A] reserving DPLL 0

<7> [42.932745] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x1, on 1

<7> [42.933119] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0

<7> [42.933528] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0

<7> [42.933843] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0

<7> [42.934406] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:111:eDP-1] hw state readout: enabled

<7> [42.934821] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:119:DP-1] hw state readout: disabled

<7> [42.935226] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:128:HDMI-A-1] hw state readout: disabled

<7> [42.935603] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:134:DP-2] hw state readout: disabled

<7> [42.936048] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:140:HDMI-A-2] hw state readout: disabled

<7> [42.936629] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:35:plane 1A] min_cdclk 373250 kHz

<7> [42.937010] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:44:plane 2A] min_cdclk 0 kHz

<7> [42.937340] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:53:cursor A] min_cdclk 0 kHz

<7> [42.937631] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:59:pipe A] min_cdclk 373250 kHz

<7> [42.937939] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 1B] min_cdclk 0 kHz

<7> [42.938320] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:69:plane 2B] min_cdclk 0 kHz

<7> [42.938606] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:78:cursor B] min_cdclk 0 kHz

<7> [42.938936] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:84:pipe B] min_cdclk 0 kHz

<7> [42.939260] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 1C] min_cdclk 0 kHz

<7> [42.939602] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:plane 2C] min_cdclk 0 kHz

<7> [42.939911] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:103:cursor C] min_cdclk 0 kHz

<7> [42.940242] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:109:pipe C] min_cdclk 0 kHz

<7> [42.940554] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:59:pipe A] dbuf slices 0x1, ddb (0 - 446), active pipes 0x1, mbus joined: no

<7> [42.940874] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:84:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no

<7> [42.941206] i915 0000:00:02.0: [drm:skl_wm_get_hw_state [i915]] [CRTC:109:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no

<7> [42.942221] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:59:pipe A] enable: yes [setup_hw_state]

<7> [42.942534] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [42.942813] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0

<7> [42.943198] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [42.943526] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [42.943815] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0

<7> [42.944112] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [42.944498] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m_n: lanes: 4; data_m: 4348677, data_n: 8388608, link_m: 362389, link_n: 524288, tu: 64

<7> [42.944783] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [42.945104] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: enabled

<7> [42.945425] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sdp split: disabled

<7> [42.945782] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] psr: disabled, selective update: disabled, panel replay: disabled, selective fetch: disabled

<7> [42.946103] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] minimum hblank: 0

<7> [42.946431] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0

<7> [42.946709] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] scanline offset: 1

<7> [42.947085] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0, set context latency: 0

<7> [42.947438] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, fixed rr: no, vmin: 0, vmax: 0, flipline: 0, pipeline full: 0, guardband: 0 vsync start: 0, vsync end: 0

<7> [42.947745] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: vmin vblank: 0, vmax vblank: 0, vmin vtotal: 0, vmax vtotal: 0

<7> [42.948095] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0

<7> [42.948449] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa

<7> [42.948756] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa

<7> [42.949061] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa

<7> [42.949397] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa

<7> [42.949779] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa

<7> [42.950131] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pixel rate 373250, min cdclk 373250, min voltage level 0

<7> [42.950471] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 73, ips linetime: 0

<7> [42.950747] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [42.951128] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe src: 3200x1800+0+0

<7> [42.951422] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [42.951699] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0

<7> [42.951998] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [42.952367] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: ctrl1: 0x1, cfgcr1: 0x0, cfgcr2: 0x0

<7> [42.952641] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [42.952938] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [42.953250] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [42.953585] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [42.953879] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [42.954189] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [42.954454] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [42.954782] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:84:pipe B] enable: no [setup_hw_state]

<7> [42.955106] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:109:pipe C] enable: no [setup_hw_state]

<7> [42.955635] i915 0000:00:02.0: [drm:skl_get_initial_plane_config [i915]] [CRTC:59:pipe A][PLANE:35:plane 1A] with fb: size=3200x1800@32, offset=0, pitch 12800, size 0x15f9000

<7> [42.955995] i915 0000:00:02.0: [drm:initial_plane_vma [i915]] Using dma_addr=0x000000007c000000, based on initial plane programming

<7> [42.956302] i915 0000:00:02.0: [drm:_i915_gem_object_stolen_init [i915]] creating preallocated stolen object: stolen_offset=0x0000000000000000, size=0x00000000015f9000

<7> [42.958294] i915 0000:00:02.0: [drm:initial_plane_vma [i915]] Initial plane fb bound to 0x0 in the ggtt (original 0x0)

<7> [42.959013] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[15f9000, 15fb000] for use by error capture

<7> [42.959318] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [15fb000, 100000000]

<7> [42.959650] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0

<7> [42.959981] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 5 GT workarounds on global

<7> [42.961657] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 8 engine workarounds on rcs'0

<7> [42.961988] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 5 whitelist workarounds on rcs'0

<7> [42.962273] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 12 context workarounds on rcs'0

<7> [42.989522] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed rcs'0 to rcs0

<7> [42.989813] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed bcs'0 to bcs0

<7> [42.990162] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed vcs'0 to vcs0

<7> [42.990447] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed vecs'0 to vecs0

<7> [42.990763] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:59:pipe A] FQ 0: start 0x8

<7> [42.991094] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:59:pipe A] FQ 1: start 0x108

<7> [42.991413] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:59:pipe A] FQ 2: start 0x208

<7> [42.991689] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:59:pipe A] FQ 3: start 0x308

<7> [42.992050] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:59:pipe A] FQ 4: start 0x3c8

<7> [42.992350] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:84:pipe B] FQ 0: start 0x8

<7> [42.992639] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:84:pipe B] FQ 1: start 0x108

<7> [42.992940] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:84:pipe B] FQ 2: start 0x208

<7> [42.993273] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:84:pipe B] FQ 3: start 0x308

<7> [42.993557] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:84:pipe B] FQ 4: start 0x3c8

<7> [42.994211] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:109:pipe C] FQ 0: start 0x8

<7> [42.994583] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:109:pipe C] FQ 1: start 0x108

<7> [42.994900] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:109:pipe C] FQ 2: start 0x208

<7> [42.995253] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:109:pipe C] FQ 3: start 0x308

<7> [42.995583] i915 0000:00:02.0: [drm:intel_flipq_init [i915]] [CRTC:109:pipe C] FQ 4: start 0x3c8

<7> [42.996326] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:59:pipe A] dbuf slices 0x1 -> 0x1, ddb (0 - 446) -> (0 - 892), active pipes 0x1 -> 0x1

<7> [42.996914] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:59:pipe A] dbuf slices 0x1 -> 0x1, ddb (0 - 446) -> (0 - 892), active pipes 0x1 -> 0x1

<7> [42.997258] i915 0000:00:02.0: [drm:skl_print_plane_ddb_changes [i915]] [PLANE:35:plane 1A] ddb ( 0 - 446) -> ( 0 - 856), size 446 -> 856

<7> [42.997555] i915 0000:00:02.0: [drm:skl_print_plane_ddb_changes [i915]] [PLANE:53:cursor A] ddb ( 0 - 0) -> ( 856 - 892), size 0 -> 36

<7> [42.998272] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] level *wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm

<7> [42.998635] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0

<7> [42.998966] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 7, 58, 84, 96, 184, 227, 245, 288, 0, 0, 0

<7> [42.999332] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 8, 59, 85, 97, 185, 228, 246, 289, 0, 0, 0

<7> [42.999645] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:35:plane 1A] min_ddb_uv 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [43.000019] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:84:pipe B] enable: no [fastset]

<7> [43.000332] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:109:pipe C] enable: no [fastset]

<7> [43.014580] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:84:pipe B]

<7> [43.015114] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:109:pipe C]

<7> [43.024203] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:111:eDP-1] adding connector to sysfs

<7> [43.028759] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:111:eDP-1] backlight device intel_backlight registered

<7> [43.029404] i915 0000:00:02.0: [drm:intel_panel_register [i915]] [CONNECTOR:111:eDP-1] Registered panel device 'card0-eDP-1', has fwnode: yes

<7> [43.029840] i915 0000:00:02.0: [drm:intel_panel_register [i915]] [CONNECTOR:111:eDP-1] Panel prepare

<7> [43.031618] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1

<7> [43.036418] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:111:eDP-1] generating connector hotplug event

<7> [43.036618] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:119:DP-1] adding connector to sysfs

<7> [43.038241] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1

<7> [43.041333] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:119:DP-1] generating connector hotplug event

<7> [43.041479] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:128:HDMI-A-1] adding connector to sysfs

<7> [43.042702] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:128:HDMI-A-1] generating connector hotplug event

<7> [43.043378] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:134:DP-2] adding connector to sysfs

<7> [43.045514] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DDI C/PHY C bus for card0-DP-2

<7> [43.049324] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:134:DP-2] generating connector hotplug event

<7> [43.049502] i915 0000:00:02.0: [drm:drm_sysfs_connector_add] [CONNECTOR:140:HDMI-A-2] adding connector to sysfs

<7> [43.051660] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:140:HDMI-A-2] generating connector hotplug event

<6> [43.055928] [drm] Initialized i915 1.6.0 for 0000:00:02.0 on minor 0

<7> [43.062198] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 5 outputs detected

<6> [43.114979] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)

<6> [43.132305] input: Video Bus as /devices/pci0000:00/acpi.video_bus.0/input/input23

<7> [43.141756] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)

<7> [43.146013] check_position_fix: snd_hda_intel 0000:00:1f.3: Using SKL position fix

<6> [43.146027] snd_hda_intel 0000:00:1f.3: codec_mask forced to 0x4

<7> [43.147474] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-1]

<7> [43.148817] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] found possible fb from [PLANE:35:plane 1A]

<7> [43.150158] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:84:pipe B] not active, skipping

<7> [43.150631] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:109:pipe C] not active, skipping

<7> [43.151100] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] checking [PLANE:35:plane 1A] for BIOS fb

<7> [43.151518] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:59:pipe A] area: 3200x1800, bpp: 32, size: 23040000

<7> [43.151983] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] fb big enough [PLANE:35:plane 1A] (23040000 >= 23040000)

<7> [43.152417] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:84:pipe B] not active, skipping

<7> [43.152826] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] [CRTC:109:pipe C] not active, skipping

<7> [43.153922] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:119:DP-1] status updated from unknown to disconnected (epoch counter 0->1)

<7> [43.154634] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]

<7> [43.156160] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [43.156619] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [43.156904] i915 0000:00:02.0: [drm:intel_fbdev_setup [i915]] using BIOS fb for initial console

<7> [43.157261] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [43.157697] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [43.158680] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [43.158694] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [43.159146] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [43.159698] i915 0000:00:02.0: [drm:drm_client_modeset_probe]

<7> [43.162763] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [43.162779] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [43.163467] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:128:HDMI-A-1] status updated from unknown to disconnected (epoch counter 0->1)

<7> [43.164284] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-2]

<7> [43.169650] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:134:DP-2] status updated from unknown to disconnected (epoch counter 0->1)

<7> [43.170434] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:140:HDMI-A-2]

<7> [43.172603] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [43.174640] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [43.175349] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [43.175822] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [43.175835] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [43.176251] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [43.182395] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [43.182413] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [43.184216] i915 0000:00:02.0: [drm:intel_hotplug_detect_connector [i915]] [CONNECTOR:140:HDMI-A-2] status updated from unknown to disconnected (epoch counter 0->1)

<7> [43.186516] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event

<7> [43.186588] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1]

<7> [43.186609] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:eDP-1]

<7> [43.191207] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [43.191561] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [43.192749] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [43.194573] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.

<7> [43.194588] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD monitor

<7> [43.194604] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD size 20, SAD count 0

<7> [43.194672] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] VRR capable: no

<7> [43.195529] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [43.196016] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no

<7> [43.198767] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1] status updated from unknown to connected

<7> [43.199440] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event

<7> [43.201885] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1] probed modes:

<7> [43.201908] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa

<7> [43.201921] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa

<7> [43.201940] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-1]

<7> [43.201952] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-1]

<7> [43.206729] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-1] disconnected

<7> [43.206753] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]

<7> [43.206767] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]

<7> [43.207911] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [43.208339] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [43.210562] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [43.212837] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [43.212875] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [43.213353] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [43.217251] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [43.217266] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [43.217765] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected

<7> [43.221313] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-2]

<7> [43.221330] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-2]

<7> [43.225970] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-2] disconnected

<7> [43.225993] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:140:HDMI-A-2]

<7> [43.226007] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:140:HDMI-A-2]

<7> [43.226790] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [43.227255] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [43.227875] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [43.228371] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [43.228383] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [43.228785] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [43.232599] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [43.232613] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [43.233182] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:140:HDMI-A-2] disconnected

<7> [43.233197] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:eDP-1] enabled? yes

<7> [43.233259] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:119:DP-1] enabled? no

<7> [43.233268] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:128:HDMI-A-1] enabled? no

<7> [43.233277] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:134:DP-2] enabled? no

<7> [43.233285] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:140:HDMI-A-2] enabled? no

<7> [43.233694] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [43.233753] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:eDP-1] found preferred mode: 3200x1800

<7> [43.233764] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [43.234339] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:59:pipe A] desired mode 3200x1800 set (0,0)

<6> [43.235497] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops intel_audio_component_bind_ops [i915])

<7> [43.237088] i915 0000:00:02.0: [drm:intel_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10

<7> [43.237591] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane

<7> [43.238657] i915 0000:00:02.0: [drm:intel_fbdev_driver_fbdev_probe [i915]] re-using BIOS fb

<7> [43.242365] i915 0000:00:02.0: [drm:intel_fbdev_driver_fbdev_probe [i915]] allocated 3200x1800 fb

<7> [43.244283] azx_first_init: snd_hda_intel 0000:00:1f.3: chipset global capabilities = 0x9701

<7> [43.251048] azx_init_pci: snd_hda_intel 0000:00:1f.3: Clearing TCSEL

<7> [43.251067] azx_init_pci: snd_hda_intel 0000:00:1f.3: SCH snoop: Enabled

<6> [43.259521] fbcon: i915drmfb (fb0) is primary device

<7> [43.269837] i915 0000:00:02.0: [drm:intel_backlight_device_update_status [i915]] updating intel_backlight, brightness=46/937

<7> [43.273815] i915 0000:00:02.0: [drm:intel_panel_actually_set_backlight [i915]] [CONNECTOR:111:eDP-1] set backlight level = 81

<7> [43.280844] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:111:eDP-1] Limiting target display pipe bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)

<7> [43.283265] i915 0000:00:02.0: [drm:intel_dp_compute_config_limits [i915]] [ENCODER:110:DDI A/PHY A][CRTC:59:pipe A] DP link limits: pixel clock 373250 kHz DSC off max lanes 4 max rate 540000 max pipe_bpp 24 min link_bpp 18.0000 max link_bpp 24.0000

<7> [43.283676] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp input 24 compressed 0.0000 HDR no link rate required 1119750 available 2160000

<7> [43.284124] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:59:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0

<7> [43.284554] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:110:DDI A/PHY A] [CRTC:59:pipe A]

<7> [43.285065] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:44:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [43.285454] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:44:plane 2A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [43.286581] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:44:plane 2A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [43.288604] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:44:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [43.289120] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:44:plane 2A] min_ddb_uv 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [43.289553] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:53:cursor A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [43.290022] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:53:cursor A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [43.290437] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:53:cursor A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [43.290845] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:53:cursor A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [43.291277] i915 0000:00:02.0: [drm:skl_print_plane_wm_changes [i915]] [PLANE:53:cursor A] min_ddb_uv 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [43.291776] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:59:pipe A] enable: yes [fastset]

<7> [43.292249] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [43.292687] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0

<7> [43.293149] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [43.293586] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [43.296175] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] joiner: no, pipes: 0x0

<7> [43.296664] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [43.297220] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m_n: lanes: 4; data_m: 4348677, data_n: 8388608, link_m: 362389, link_n: 524288, tu: 64

<7> [43.297649] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [43.298095] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: enabled

<7> [43.298510] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sdp split: disabled

<7> [43.298948] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] psr: enabled, selective update: disabled, panel replay: disabled, selective fetch: disabled

<7> [43.299378] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] minimum hblank: 0

<7> [43.299798] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [43.300258] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] DP SDP: VSC, revision 2, length 8

<7> [43.300687] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pixelformat: RGB

<7> [43.301468] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] colorimetry: sRGB

<7> [43.302107] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bpc: 0

<7> [43.302537] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dynamic range: VESA range

<7> [43.302994] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] content type: Not defined

<7> [43.303429] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] scanline offset: 1

<7> [43.303843] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0, set context latency: 0

<7> [43.304297] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, fixed rr: no, vmin: 0, vmax: 0, flipline: 0, pipeline full: 0, guardband: 0 vsync start: 0, vsync end: 0

<7> [43.304721] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: vmin vblank: 0, vmax vblank: 0, vmin vtotal: 0, vmax vtotal: 0

<7> [43.307306] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: dc balance: no, vmin: 0 vmax: 0 guardband: 0, slope: 0 max increase: 0 max decrease: 0 vblank target: 0

<7> [43.307796] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa

<7> [43.308267] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa

<7> [43.308691] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa

<7> [43.309187] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa

<7> [43.309672] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa

<7> [43.310126] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pixel rate 373250, min cdclk 373250, min voltage level 0

<7> [43.310555] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 73, ips linetime: 0

<7> [43.310994] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [43.311409] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe src: 3200x1800+0+0

<7> [43.311825] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [43.312278] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] sharpness strength: 0, sharpness tap size: 0, sharpness enable: 0

<7> [43.312693] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [43.313148] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] dpll_hw_state: ctrl1: 0x1, cfgcr1: 0x0, cfgcr2: 0x0

<7> [43.313518] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x2 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [43.313817] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [43.314148] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [43.314444] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [43.314736] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [43.315055] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [43.315354] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [43.315655] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:35:plane 1A] fb: [FB:144] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes

<7> [43.316036] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0

<7> [43.316404] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0

<7> [43.316704] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:44:plane 2A] fb: [NOFB], visible: no

<7> [43.317114] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:53:cursor A] fb: [NOFB], visible: no

<7> [43.331753] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1

<7> [43.336721] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:111:eDP-1]

<7> [43.337401] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:59:pipe A]

<7> [43.341275] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV

<6> [43.343323] Console: switching to colour frame buffer device 200x56

<7> [43.366633] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port B

<7> [43.367552] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port B

<7> [43.368412] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port B

<7> [43.368828] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port C

<7> [43.369259] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port C

<7> [43.369687] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port C

<7> [43.370127] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port D

<7> [43.370532] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port D

<7> [43.371000] i915 0000:00:02.0: [drm:intel_audio_component_get_eld [i915]] Not valid for port D

<6> [43.373841] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device

<7> [43.373895] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: display version: 9

<7> [43.374401] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: display stepping: H0

<7> [43.374815] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: cursor_needs_physical: no

<7> [43.375617] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_cdclk_crawl: no

<7> [43.376399] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_cdclk_squash: no

<7> [43.377053] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_ddi: yes

<7> [43.377456] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dp_mst: yes

<7> [43.377821] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dsb: no

<7> [43.378482] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_fpga_dbg: yes

<7> [43.379094] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_gmch: no

<7> [43.379531] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hotplug: yes

<7> [43.380153] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hti: no

<7> [43.380590] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_ipc: yes

<7> [43.382898] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_overlay: no

<7> [43.383307] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_psr: yes

<7> [43.383707] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_psr_hw_tracking: yes

<7> [43.384693] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: overlay_needs_physical: no

<7> [43.385092] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: supports_tv: no

<7> [43.385507] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_hdcp: yes

<7> [43.386081] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dmc: yes

<7> [43.386501] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: has_dsc: no

<7> [43.386945] i915 0000:00:02.0: [drm:intel_display_driver_register [i915]] i915 display info: rawclk rate: 24000 kHz

<7> [43.388621] [drm:intel_dsm_detect.isra.0 [i915]] no _DSM method for intel device

<7> [43.391926] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D

<7> [43.392713] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C

<7> [43.393158] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B

<7> [43.393665] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: pciid=0x1916 rev=0x07 platform=SKYLAKE (subplatform=0x1) gen=9

<7> [43.394046] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: graphics version: 9

<7> [43.394382] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: media version: 9

<7> [43.394731] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: graphics stepping: H0

<7> [43.395274] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: media stepping: H0

<7> [43.395617] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: gt: 2

<7> [43.395987] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: memory-regions: 0x21

<7> [43.396322] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: page-sizes: 0x11000

<7> [43.396656] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: platform: SKYLAKE

<7> [43.397089] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: ppgtt-size: 48

<7> [43.397436] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: ppgtt-type: 2

<7> [43.397773] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: dma_mask_size: 39

<7> [43.398318] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: is_mobile: no

<7> [43.398659] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: require_force_probe: no

<7> [43.398939] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: is_dgfx: no

<7> [43.399252] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_64bit_reloc: yes

<7> [43.399581] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_64k_pages: no

<7> [43.399919] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: gpu_reset_clobbers_display: no

<7> [43.400226] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_reset_engine: yes

<7> [43.400562] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_3d_pipeline: yes

<7> [43.400917] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_flat_ccs: no

<7> [43.401248] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_global_mocs: no

<7> [43.401563] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_gmd_id: no

<7> [43.401903] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_gt_uc: yes

<7> [43.402228] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_heci_pxp: no

<7> [43.402550] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_heci_gscfi: no

<7> [43.402895] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_guc_deprivilege: no

<7> [43.403173] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_guc_tlb_invalidation: no

<7> [43.403441] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_l3_ccs_read: no

<7> [43.403672] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_l3_dpf: no

<7> [43.403982] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_llc: yes

<7> [43.404294] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_logical_ring_contexts: yes

<7> [43.404519] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_logical_ring_elsq: no

<7> [43.404746] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_media_ratio_mode: no

<7> [43.404997] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_mslice_steering: no

<7> [43.405272] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oa_bpc_reporting: no

<7> [43.405506] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oa_slice_contrib_limits: no

<7> [43.405741] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_oam: no

<7> [43.406022] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_one_eu_per_fuse_bit: no

<7> [43.406342] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_pxp: no

<7> [43.406611] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rc6: yes

<7> [43.406846] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rc6p: no

<7> [43.407108] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_rps: yes

<7> [43.407381] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_runtime_pm: yes

<7> [43.407606] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_snoop: no

<7> [43.407830] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_coherent_ggtt: yes

<7> [43.408159] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: tuning_thread_rr_after_dep: no

<7> [43.408487] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: unfenced_needs_alignment: no

<7> [43.408765] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: hws_needs_physical: no

<7> [43.409026] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has_pooled_eu: no

<7> [43.409328] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: iommu: enabled

<7> [43.409658] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: available engines: 40403

<7> [43.410006] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice total: 1, mask=0001

<7> [43.410345] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: subslice total: 3

<7> [43.410672] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice0: 3 subslices, mask=00000007

<7> [43.411008] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice1: 0 subslices, mask=00000000

<7> [43.411329] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: slice2: 0 subslices, mask=00000000

<7> [43.411595] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: EU total: 24

<7> [43.411825] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: EU per subslice: 8

<7> [43.412164] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has slice power gating: no

<7> [43.412485] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has subslice power gating: no

<7> [43.412746] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] device info: has EU power gating: yes

<6> [43.413276] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled

<6> [43.413279] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled

<6> [43.413282] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled

<6> [43.421238] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input24

<7> [43.427651] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]

<7> [43.427677] i915 0000:00:02.0: [drm:drm_client_modeset_probe]

<7> [43.428364] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1]

<7> [43.428390] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:eDP-1]

<7> [43.429102] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [43.432199] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [43.432617] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [43.433319] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.

<7> [43.433331] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD monitor

<7> [43.433356] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD size 20, SAD count 0

<7> [43.433434] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] VRR capable: no

<7> [43.433825] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [43.435438] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no

<7> [43.441197] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1] probed modes:

<7> [43.441243] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa

<7> [43.441254] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa

<7> [43.441267] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-1]

<7> [43.441279] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-1]

<7> [43.446102] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-1] disconnected

<7> [43.446124] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]

<7> [43.446144] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]

<7> [43.447277] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [43.447692] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [43.448746] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [43.449487] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [43.449499] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [43.450819] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [43.457592] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [43.457605] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [43.458052] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected

<7> [43.458068] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-2]

<7> [43.458080] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-2]

<7> [43.463425] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-2] disconnected

<7> [43.463446] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:140:HDMI-A-2]

<7> [43.463464] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:140:HDMI-A-2]

<7> [43.464194] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [43.464583] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [43.465173] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [43.468985] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [43.469014] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [43.469422] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [43.476943] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [43.476959] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [43.477284] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:140:HDMI-A-2] disconnected

<7> [43.477295] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:eDP-1] enabled? yes

<7> [43.477302] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:119:DP-1] enabled? no

<7> [43.477307] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:128:HDMI-A-1] enabled? no

<7> [43.477312] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:134:DP-2] enabled? no

<7> [43.477317] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:140:HDMI-A-2] enabled? no

<7> [43.477565] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [43.477604] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:eDP-1] found preferred mode: 3200x1800

<7> [43.477610] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config

<7> [43.477670] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:59:pipe A] desired mode 3200x1800 set (0,0)

<6> [43.486668] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input25

<6> [43.490337] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input26

<7> [43.499998] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0

<7> [43.500663] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]

<7> [43.500681] i915 0000:00:02.0: [drm:drm_client_modeset_probe]

<7> [43.501243] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1]

<7> [43.501263] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:eDP-1]

<7> [43.501817] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [43.503260] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [43.503691] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [43.505737] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.

<7> [43.505751] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD monitor

<7> [43.505771] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:111:eDP-1] ELD size 20, SAD count 0

<7> [43.505832] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] VRR capable: no

<7> [43.506235] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [43.506535] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:111:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no

<7> [43.508729] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:eDP-1] probed modes:

<7> [43.508748] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa

<7> [43.508756] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa

<7> [43.508766] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-1]

<7> [43.508773] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-1]

<7> [43.513940] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-1] disconnected

<7> [43.513963] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]

<7> [43.513976] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]

<7> [43.515206] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [43.515596] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [43.516763] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [43.517236] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [43.517249] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [43.517602] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [43.521877] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [43.521894] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [43.522367] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected

<7> [43.522385] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-2]

<7> [43.522398] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-2]

<7> [43.524934] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [43.526964] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-2] disconnected

<7> [43.526986] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:140:HDMI-A-2]

<7> [43.526999] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:140:HDMI-A-2]

<7> [43.527668] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [43.529428] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [43.530365] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [43.530774] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [43.530787] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [43.531220] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [43.531337] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [43.535532] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [43.535550] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [43.536187] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:140:HDMI-A-2] disconnected

<7> [43.536204] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:eDP-1] enabled? yes

<7> [43.536215] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:119:DP-1] enabled? no

<7> [43.536224] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:128:HDMI-A-1] enabled? no

<7> [43.536232] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:134:DP-2] enabled? no

<7> [43.536239] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:140:HDMI-A-2] enabled? no

<7> [43.536503] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [43.536559] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:111:eDP-1] found preferred mode: 3200x1800

<7> [43.536569] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config

<7> [43.536663] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:59:pipe A] desired mode 3200x1800 set (0,0)

<7> [43.553503] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0

<7> [43.599657] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0

<7> [43.600038] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [43.664558] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0

<6> [43.665001] [IGT] i915_module_load: finished subtest load, SUCCESS

<6> [43.665402] [IGT] i915_module_load: exiting, ret=0

Results for igt@i915_module_load@load