Results for igt@kms_addfb_basic@basic-y-tiled-legacy

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.00 seconds
Igt-Version 
IGT-Version: 2.4-gcb6666eae (x86_64) (Linux: 7.0.0-rc6-next-20260401-next-20260401-gbd0f139e5fc1+ x86_64)
Out 
Using IGT_SRANDOM=1775056325 for randomisation
Opened device: /dev/dri/card0
Starting subtest: basic-y-tiled-legacy
Subtest basic-y-tiled-legacy: SUCCESS (0.000s)
Err 
Starting subtest: basic-y-tiled-legacy
Subtest basic-y-tiled-legacy: SUCCESS (0.000s)
Dmesg
<6> [94.636421] [IGT] kms_addfb_basic: executing
<7> [94.640223] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [94.641052] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [94.641571] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [94.642025] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] bad framebuffer format .... little-endian (0x00000000)
<7> [94.642274] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:134]
<7> [94.642661] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:134]
<7> [94.642800] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:134]
<6> [94.643349] [IGT] kms_addfb_basic: starting subtest basic-y-tiled-legacy
<7> [94.643714] i915 0000:00:02.0: [drm:i915_bo_framebuffer_init [i915]] No Y tiling for legacy addfb
<7> [94.643975] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] could not create framebuffer
<6> [94.644059] [IGT] kms_addfb_basic: finished subtest basic-y-tiled-legacy, SUCCESS
<7> [94.649751] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [94.649762] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [94.650051] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [94.651207] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [94.651899] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [94.652611] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [94.653193] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [94.653605] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [94.654441] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.655960] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.657482] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.659061] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.660668] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.662472] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.664197] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.665750] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.667398] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.668407] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [94.669253] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [94.669714] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [94.670313] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [94.671059] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2]
<7> [94.671072] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [94.675501] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2] disconnected
<7> [94.676035] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1]
<7> [94.676043] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [94.744053] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [94.747676] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.747687] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.747972] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [94.751030] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.751039] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [94.751347] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1] disconnected
<7> [94.751987] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1]
<7> [94.751998] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:111:DP-1]
<7> [94.752697] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [94.753117] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [94.754063] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.755589] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.757612] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.759181] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.760889] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.762617] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.764301] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.765985] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.767600] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [94.768695] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [94.769549] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [94.769988] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [94.770803] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:111:DP-1] disconnected
<7> [94.770863] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2]
<7> [94.770875] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:124:DP-2]
<7> [94.775458] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:DP-2] disconnected
<7> [94.775493] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1]
<7> [94.775502] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:130:HDMI-A-1]
<7> [94.844075] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [94.847879] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.847893] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.848306] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [94.851696] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.851709] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [94.852146] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:130:HDMI-A-1] disconnected
<6> [94.853939] [IGT] kms_addfb_basic: exiting, ret=0
<7> [94.854990] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [94.860566] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [94.861063] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [94.861547] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [94.862118] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [94.863224] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [94.879673] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
Created at 2026-04-02 09:25:36