Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.31 seconds
Igt-Version 
IGT-Version: 2.3-g53a8844b8 (x86_64) (Linux: 7.0.0-rc1-next-20260226-next-20260226-g7d6661873f6b+ x86_64)
Out 
Using IGT_SRANDOM=1772116718 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88810ce71820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x9b0 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x306/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.313s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.313s)
Dmesg
<6> [118.043338] Console: switching to colour dummy device 80x25
<6> [118.043441] [IGT] kms_pm_rpm: executing
<7> [118.046970] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [118.052985] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [118.052997] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [118.053274] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [118.054413] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [118.055088] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [118.055928] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [118.056519] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [118.056928] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [118.057868] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.059455] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.061010] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.062523] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.064222] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.065872] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.067615] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.069311] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.070864] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.071918] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [118.072670] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [118.073117] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [118.073827] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [118.074731] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [118.074743] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [118.079204] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [118.079825] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [118.079837] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [118.147675] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [118.151235] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.151248] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.151612] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [118.154938] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.154951] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [118.155309] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [118.156171] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [118.156191] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [118.157203] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [118.157740] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [118.158262] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [118.158795] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [118.159271] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [118.160293] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 2 ms
<7> [118.161215] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [118.162138] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [118.162939] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [118.164044] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.165930] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.167735] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.169386] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.171174] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.173049] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.174846] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.176696] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.178485] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.179625] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [118.180691] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [118.181290] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [118.182142] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [118.182198] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [118.182210] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [118.186971] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [118.187013] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [118.187024] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [118.255206] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [118.259512] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.259526] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.259934] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [118.263581] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.263596] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [118.264126] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [118.264215] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1]
<7> [118.264230] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [118.265343] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [118.266016] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [118.267215] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.268849] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.270527] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.272241] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.273994] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.275754] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.277588] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.279455] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.281239] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.282214] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [118.283164] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [118.283639] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [118.284469] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:110:DP-1] disconnected
<7> [118.284639] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2]
<7> [118.284656] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [118.289119] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:123:DP-2] disconnected
<7> [118.289237] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1]
<7> [118.289249] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [118.357667] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [118.361206] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.361219] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.361583] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [118.365225] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.365241] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [118.365852] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:129:HDMI-A-1] disconnected
<7> [118.373729] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [118.374169] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [118.374522] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [118.374903] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [118.375867] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [119.373879] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [119.382061] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [119.406769] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [119.419181] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [119.421142] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.422075] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [119.422247] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.422849] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.423504] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [119.423500] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [119.423926] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [119.425046] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [119.425341] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [119.426154] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.427601] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.429155] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.430604] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.432251] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.433863] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.435499] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.437191] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.438644] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.439571] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [119.440571] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [119.440614] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [119.440926] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [119.441157] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.441380] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.442329] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.442940] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.443598] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [119.444424] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [119.445632] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [119.450038] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [119.518217] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [119.521948] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.521961] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [119.522293] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [119.525564] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.525577] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [119.526257] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [119.548786] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [119.549435] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [119.549994] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.550640] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.551723] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [119.552838] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [119.561635] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [119.630981] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [119.681699] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:58:pipe A]
<7> [119.693756] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [119.699839] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [119.700195] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.700425] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.700979] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.701850] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:83:pipe B]
<7> [119.702106] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:108:pipe C]
<7> [119.702105] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<7> [119.702561] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [119.703348] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [119.703653] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [119.704432] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.705915] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.707450] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.708881] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.710496] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.712229] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.713829] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.715547] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.717061] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.717923] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [119.718885] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [119.719572] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [119.720632] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [119.720963] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [119.721240] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.721545] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.722282] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.722854] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.723443] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [119.723970] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [119.728341] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [119.796210] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [119.799958] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.799970] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [119.800267] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [119.803431] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.803443] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [119.828829] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [119.829472] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [119.830076] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.830765] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.831859] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [119.832551] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [119.840614] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [119.918832] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [119.938292] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [119.939327] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.940292] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.941784] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.943307] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:110:DP-1]
<6> [119.945462] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [119.945328] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [119.947564] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [119.948772] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [119.950946] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.953808] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.956013] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.957896] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.959939] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.961770] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.963729] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.965602] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.967373] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.968349] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [119.969605] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [119.970477] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [119.972240] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:123:DP-2]
<7> [119.976796] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:129:HDMI-A-1]
<7> [120.044625] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [120.049007] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.049029] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [120.049656] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [120.053830] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.053852] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [120.053872] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [120.054995] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [120.056036] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [120.057014] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [120.058642] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [120.059374] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.060370] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [120.061674] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [120.063270] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [120.064026] [IGT] kms_pm_rpm: exiting, ret=0
<6> [120.071223] Console: switching to colour frame buffer device 128x48
Created at 2026-02-26 19:10:10