Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.42 seconds
Igt-Version	IGT-Version: 2.3-ga85208a45 (x86_64) (Linux: 7.0.0-rc1-next-20260225-next-20260225-g877552aa8758+ x86_64)
Out	Using IGT_SRANDOM=1772039302 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888127d69820 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x140b/0x1d70 [i915] intel_atomic_commit+0x2e8/0x330 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x548/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1250/0x26e0 do_syscall_64+0xdd/0x1470 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.417s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888127d69820 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x2f0 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b7c/0x26e0 do_syscall_64+0xdd/0x1470
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.417s)
Dmesg	<6> [76.429447] Console: switching to colour dummy device 80x25 <6> [76.429522] [IGT] kms_pm_rpm: executing <6> [76.431479] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [76.431684] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [76.435733] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [76.435740] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [76.439953] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [76.440202] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [76.440205] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [76.444411] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [76.444731] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [76.444734] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [76.448962] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [76.449235] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [76.449238] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [76.453471] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [76.453483] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [76.453485] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [76.457699] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [76.457710] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [76.457713] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [76.461512] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [76.461685] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [76.461823] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [76.463105] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [76.463124] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] <7> [76.463127] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [76.468047] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:389:HDMI-A-1] disconnected <7> [76.468079] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] <7> [76.468082] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [76.472914] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:399:DP-1] disconnected <7> [76.472944] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] <7> [76.472946] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [76.477791] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:407:HDMI-A-2] disconnected <7> [76.581622] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [77.479946] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [77.485893] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [77.487306] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [77.487750] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [77.488031] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [77.488171] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [77.490412] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [77.515781] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [77.523620] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [77.523849] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [77.524018] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [77.524243] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [77.524444] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [77.524654] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [77.524849] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [77.525026] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [77.525500] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [77.526314] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [77.527763] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [77.530043] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [77.530495] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [77.539086] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [77.540316] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [77.540523] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [77.541612] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [77.545271] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [77.550183] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [77.555016] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [77.555158] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [77.555299] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [77.556145] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [77.557581] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [77.557696] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [77.575693] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [77.576050] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [77.576367] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [77.577895] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [77.578435] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [77.583025] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [77.584418] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [77.584680] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [77.584972] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [77.585121] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [77.587654] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [77.658798] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [77.671423] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [77.679738] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [77.680559] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [77.681480] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [77.682424] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [77.683368] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [77.684281] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [77.685189] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [77.686068] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [77.686984] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [77.687118] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [77.687558] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [77.688261] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [77.688402] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [77.695794] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [77.695995] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [77.696258] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [77.697109] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [77.698753] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <7> [77.698978] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [77.703023] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [77.707334] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [77.707439] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [77.724783] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [77.724932] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [77.725159] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [77.726682] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [77.727483] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [77.733331] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [77.734991] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [77.735785] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [77.736682] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [77.737270] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [77.742660] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [77.820688] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [77.828752] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [77.829578] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [77.830516] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [77.831514] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [77.832455] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [77.833408] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [77.834304] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [77.835169] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [77.836819] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [77.837576] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [77.839018] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [77.839706] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [77.839840] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [77.847199] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [77.847350] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [77.847713] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <6> [77.849704] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [77.849892] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:150:pipe A] <7> [77.852508] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <7> [77.857406] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2] <7> [77.862370] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [77.863381] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [77.864789] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:268:pipe B] <7> [77.864875] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:386:pipe C] <7> [77.950084] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [77.951014] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [77.951849] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [77.954124] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [77.955313] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [77.963786] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [77.965720] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [77.966745] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [77.967830] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [77.968356] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [77.972699] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [78.083883] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [78.091802] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [78.092631] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [78.093554] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [78.094506] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [78.095458] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [78.096389] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [78.097296] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [78.098203] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [78.099133] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [78.099945] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [78.100914] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [78.103468] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [78.104158] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [78.116953] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [78.117366] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [78.117511] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [78.118260] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [78.119857] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [78.119874] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:389:HDMI-A-1] <6> [78.120226] [IGT] kms_pm_rpm: exiting, ret=0 <7> [78.124118] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:399:DP-1] <6> [78.128562] Console: switching to colour frame buffer device 160x45 <7> [78.128514] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:407:HDMI-A-2]

Created at 2026-02-25 20:02:57