Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.43 seconds
Igt-Version	IGT-Version: 2.3-gf2a44e594 (x86_64) (Linux: 7.0.0-rc1-next-20260224-next-20260224-g3ef088b0c577+ x86_64)
Out	Using IGT_SRANDOM=1771946701 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff88813e545818 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x140b/0x1d70 [i915] intel_atomic_commit+0x2e8/0x330 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x548/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1250/0x26e0 do_syscall_64+0xdd/0x1470 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.426s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff88813e545818 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x2f0 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b7c/0x26e0 do_syscall_64+0xdd/0x1470
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.426s)
Dmesg	<6> [71.631876] Console: switching to colour dummy device 80x25 <6> [71.631929] [IGT] kms_pm_rpm: executing <6> [71.633757] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [71.633982] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [71.637925] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [71.637931] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [71.642149] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [71.642400] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [71.642403] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [71.646629] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [71.646865] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [71.646868] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [71.651082] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [71.651362] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [71.651365] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [71.655577] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [71.655588] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [71.655591] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [71.659780] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [71.659791] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [71.659793] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [71.663975] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [71.663992] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [71.663994] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [71.667484] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [71.667635] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [71.667793] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [71.669156] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [71.669192] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [71.669196] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [71.674017] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [71.674047] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [71.674050] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [71.678896] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [71.786644] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [72.680388] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [72.687652] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [72.689054] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [72.689300] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [72.689580] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [72.689716] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [72.691912] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [72.717043] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [72.723875] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [72.724024] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [72.724199] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [72.724424] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.724625] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.724975] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.726020] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.726869] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [72.728560] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [72.729357] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [72.730786] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [72.733036] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [72.733588] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [72.742641] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [72.743864] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [72.744032] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [72.746319] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [72.748834] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [72.753710] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [72.758572] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [72.758757] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [72.758909] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [72.759687] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [72.761134] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [72.761246] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [72.779960] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [72.780225] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [72.780454] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [72.781837] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [72.782184] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [72.786696] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [72.788105] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [72.788358] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [72.788637] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [72.788774] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [72.790864] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [72.862276] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [72.873972] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [72.881802] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [72.882618] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [72.883531] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [72.884471] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.885399] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.886310] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.887216] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [72.888097] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [72.888975] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [72.889730] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [72.890728] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [72.893213] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [72.894014] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [72.903272] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [72.903516] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [72.903864] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [72.904760] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [72.906238] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [72.906489] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [72.910513] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [72.914850] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [72.914954] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [72.932930] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [72.933383] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [72.933840] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [72.935426] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [72.936148] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [72.943220] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [72.944831] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [72.945644] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [72.946583] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [72.947221] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [72.951781] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [73.027926] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [73.035742] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [73.036560] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [73.037458] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [73.038380] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [73.039298] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [73.040207] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [73.041089] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [73.041954] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [73.042837] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [73.043605] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [73.044612] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [73.047078] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [73.047853] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [73.057080] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [73.057316] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [73.057844] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <6> [73.061489] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [73.062778] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [73.062892] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [73.067630] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [73.072588] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [73.073618] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [73.075071] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [73.075176] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [73.162909] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [73.163811] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [73.164590] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [73.166640] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [73.167909] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [73.176713] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [73.178534] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [73.179531] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [73.180554] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [73.181109] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [73.184690] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [73.294135] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [73.302690] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [73.303525] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [73.304460] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [73.305411] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [73.306385] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [73.307348] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [73.308272] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [73.309168] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [73.310087] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [73.310910] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [73.311902] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [73.314396] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [73.315145] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [73.327876] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [73.328042] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [73.328172] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [73.329220] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [73.330529] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [73.330527] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <6> [73.330736] [IGT] kms_pm_rpm: exiting, ret=0 <7> [73.334792] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <6> [73.339213] Console: switching to colour frame buffer device 160x45 <7> [73.339165] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2]

Created at 2026-02-24 20:08:30