Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.31 seconds
Igt-Version 
IGT-Version: 2.3-g063e64ae4 (x86_64) (Linux: 7.0.0-rc1-next-20260223-next-20260223-g779cae956c83+ x86_64)
Out 
Using IGT_SRANDOM=1771889042 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88813e59d818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x9b0 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x306/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.314s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.314s)
Dmesg
<6> [117.443599] Console: switching to colour dummy device 80x25
<6> [117.443705] [IGT] kms_pm_rpm: executing
<7> [117.446773] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [117.453190] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [117.453201] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [117.453488] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [117.454648] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [117.455326] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [117.456002] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [117.456578] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [117.456978] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 1 ms
<7> [117.457915] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.459615] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.461174] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.462754] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.464537] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.466232] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.468094] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.469763] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.471204] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.472173] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [117.472994] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [117.473437] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [117.474172] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [117.475052] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [117.475064] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [117.479507] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [117.480340] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [117.480352] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [117.549050] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [117.552554] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.552565] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [117.552872] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [117.556056] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.556066] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [117.556072] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [117.556432] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [117.556756] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [117.557166] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [117.558168] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [117.558629] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [117.559373] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [117.559388] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [117.559800] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [117.561108] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [117.561857] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [117.562539] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [117.563274] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [117.563637] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [117.564708] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.566307] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.567965] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.569689] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.571391] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.573118] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.574908] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.576762] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.578486] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.579448] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [117.580225] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [117.580679] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [117.581452] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [117.581513] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [117.581526] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [117.585989] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [117.586031] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [117.586041] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [117.654642] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [117.658384] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.658396] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [117.658742] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [117.662205] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.662219] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [117.662800] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [117.662896] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [117.662911] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [117.664041] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [117.664675] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [117.665969] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.667172] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [117.667623] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [117.668022] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [117.668441] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [117.669360] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [117.670289] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [117.671247] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [117.672410] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.674212] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.675898] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.677797] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.679591] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.681470] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.683177] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.684910] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [117.686023] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [117.687017] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [117.687490] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [117.688231] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [117.688372] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [117.688383] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [117.692868] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [117.692972] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [117.692982] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [117.761044] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [117.764578] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.764589] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [117.764899] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [117.768250] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.768263] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [117.768771] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [117.771150] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [117.771569] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [117.771902] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [117.772530] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [117.773599] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [118.777210] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [118.785522] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [118.810202] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [118.819803] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [118.821079] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [118.821492] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [118.822857] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [118.823627] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [118.824830] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [118.824891] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [118.826063] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [118.826373] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [118.827205] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.828878] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.830347] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.832011] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.833704] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.835466] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.837113] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.838837] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.840549] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.841531] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [118.842599] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [118.843396] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [118.845313] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [118.849767] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [118.917630] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [118.921527] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.921540] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.921889] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [118.925486] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.925501] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [118.927241] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [118.927533] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [118.947112] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [118.947738] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [118.948313] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [118.949019] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [118.950043] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [118.951365] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [118.958886] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [119.032316] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [119.083087] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [119.095059] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [119.101129] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [119.101493] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.101735] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.102700] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.103667] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [119.103965] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [119.104094] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [119.104868] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [119.105200] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [119.105997] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.107552] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.109044] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.110533] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.112131] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.113834] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.115515] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.117099] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.118571] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.119479] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [119.120437] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [119.121120] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [119.122293] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [119.126712] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [119.194633] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [119.198364] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.198378] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [119.198724] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [119.202021] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.202034] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [119.202724] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [119.227272] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [119.228233] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [119.228997] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.230116] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.231556] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [119.232973] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [119.244046] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [119.317174] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [119.337831] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [119.340030] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.341293] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [119.341276] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.342867] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.346462] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<6> [119.347858] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [119.348529] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [119.349723] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [119.351447] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.353271] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.355102] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.357078] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.358854] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.360664] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.362493] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.364199] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.365790] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.366766] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [119.367862] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [119.368599] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [119.369854] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [119.374374] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [119.442630] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [119.446404] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.446416] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [119.446726] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [119.449935] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.449947] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [119.450603] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [119.450711] [IGT] kms_pm_rpm: exiting, ret=0
<7> [119.452057] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [119.452664] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [119.453274] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.453794] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.454787] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [119.455390] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.455883] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.456748] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [119.457708] Console: switching to colour frame buffer device 128x48
Created at 2026-02-24 02:59:02