Result:
git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0
| Detail | Value |
|---|---|
| Duration | 0.29 seconds |
| Igt-Version |
IGT-Version: 2.3-g07ca77c0e (x86_64) (Linux: 6.19.0-next-20260213-next-20260213-g635c467cc14e+ x86_64) |
| Out |
Using IGT_SRANDOM=1771006679 for randomisation Opened device: /dev/dri/card0 Starting subtest: force-edid Subtest force-edid: SUCCESS (0.289s) |
| Err |
Starting subtest: force-edid Subtest force-edid: SUCCESS (0.289s) |
| Dmesg |
<6> [177.417762] Console: switching to colour dummy device 80x25
<6> [177.417994] [IGT] kms_force_connector_basic: executing
<7> [177.430100] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [177.432379] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [177.444850] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [177.446488] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:527:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [177.446499] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [177.446506] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [177.450845] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [177.450869] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [177.450872] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [177.455072] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [177.455105] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [177.455108] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [177.459321] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<6> [177.459520] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [177.459849] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:527:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [177.459853] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [177.459856] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [177.518212] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [177.523859] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.523871] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.524243] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [177.529844] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.529851] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [177.530055] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] status updated from disconnected to connected
<7> [177.530110] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] probed modes:
<7> [177.530115] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [177.530120] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [177.530126] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [177.530130] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [177.530134] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [177.530151] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [177.530216] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [177.530242] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [177.530245] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [177.588667] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [177.594287] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.594296] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.594532] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [177.599955] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.599959] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [177.600133] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] probed modes:
<7> [177.600137] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [177.600141] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [177.600144] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [177.600148] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [177.600151] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [177.600552] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:527:HDMI-A-1] EDID override set
<7> [177.600568] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [177.600570] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [177.601151] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:527:HDMI-A-1] ELD monitor IGT
<7> [177.601154] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:527:HDMI-A-1] ELD size 24, SAD count 0
<7> [177.661660] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [177.667262] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [177.667393] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 (STALE)
<7> [177.667403] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 (STALE)
<7> [177.667409] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] probed modes:
<7> [177.667414] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [177.667418] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [177.667422] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [177.667426] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [177.667430] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [177.667539] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:527:HDMI-A-1] EDID override reset
<7> [177.667766] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [177.667769] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [177.728654] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [177.734278] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.734284] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.734414] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [177.739812] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.739817] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [177.739977] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:527:HDMI-A-1] EDID changed, epoch counter 2
<7> [177.740018] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa (STALE)
<7> [177.740029] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 (STALE)
<7> [177.740034] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] probed modes:
<7> [177.740037] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [177.740039] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [177.740042] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [177.740046] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [177.740049] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [177.740158] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:527:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [177.740161] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [177.740164] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [177.744386] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] status updated from connected to disconnected
<7> [177.744392] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [177.744409] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [177.744447] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [177.744465] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [177.744468] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [177.748649] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<6> [177.748917] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [177.749294] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [177.750341] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:506:eDP-1] force updated from 0 to 0 or reprobing
<7> [177.750346] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1]
<7> [177.750350] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:506:eDP-1]
<7> [177.751004] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [177.751474] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [177.751621] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.751752] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.751901] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [177.751905] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [177.751908] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD monitor
<7> [177.751910] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD size 20, SAD count 0
<7> [177.751922] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] VRR capable: yes
<7> [177.752053] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [177.752184] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [177.753000] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1] probed modes:
<7> [177.753003] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [177.753024] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1]
<7> [177.753027] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:506:eDP-1]
<7> [177.753676] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [177.754127] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [177.754256] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.754386] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.754527] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [177.754530] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [177.754532] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD monitor
<7> [177.754534] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD size 20, SAD count 0
<7> [177.754543] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] VRR capable: yes
<7> [177.754686] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [177.754819] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [177.755624] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1] probed modes:
<7> [177.755628] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [177.755704] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:506:eDP-1] EDID override reset
<7> [177.755717] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1]
<7> [177.755719] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:506:eDP-1]
<7> [177.756334] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [177.756752] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [177.756880] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.757007] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.757146] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [177.757149] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [177.757151] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD monitor
<7> [177.757153] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD size 20, SAD count 0
<7> [177.757162] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] VRR capable: yes
<7> [177.757289] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [177.757416] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [177.758163] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1] probed modes:
<7> [177.758166] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [177.758241] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:515:DP-1] EDID override reset
<7> [177.758253] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:515:DP-1]
<7> [177.758256] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:515:DP-1]
<7> [177.762487] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:515:DP-1] disconnected
<7> [177.762591] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:527:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [177.762594] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [177.762598] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [177.766971] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [177.766992] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [177.766995] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [177.771188] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [177.771255] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:527:HDMI-A-1] EDID override reset
<7> [177.771265] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [177.771268] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [177.775475] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [177.775543] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:533:DP-2] EDID override reset
<7> [177.775554] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:533:DP-2]
<7> [177.775557] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:533:DP-2]
<7> [177.775835] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:533:DP-2] disconnected
<7> [177.775897] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:542:DP-3] EDID override reset
<7> [177.775907] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:542:DP-3]
<7> [177.775910] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:542:DP-3]
<7> [177.776144] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:542:DP-3] disconnected
<7> [177.776202] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:551:DP-4] EDID override reset
<7> [177.776212] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:551:DP-4]
<7> [177.776214] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:551:DP-4]
<7> [177.776456] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:551:DP-4] disconnected
<7> [177.776513] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:560:DP-5] EDID override reset
<7> [177.776522] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:560:DP-5]
<7> [177.776525] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:560:DP-5]
<7> [177.776775] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:560:DP-5] disconnected
<6> [177.777165] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [177.777669] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [177.795317] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]
<7> [177.795324] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [177.795375] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1]
<7> [177.795379] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:506:eDP-1]
<7> [177.796061] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [177.796488] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [177.796640] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.796773] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.796919] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [177.796922] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [177.796924] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD monitor
<7> [177.796927] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD size 20, SAD count 0
<7> [177.796942] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] VRR capable: yes
<7> [177.797078] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [177.797209] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [177.798024] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1] probed modes:
<7> [177.798028] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [177.798032] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:515:DP-1]
<7> [177.798035] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:515:DP-1]
<7> [177.802219] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:515:DP-1] disconnected
<7> [177.802224] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [177.802228] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [177.806458] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [177.806463] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:533:DP-2]
<7> [177.806466] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:533:DP-2]
<7> [177.806744] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:533:DP-2] disconnected
<7> [177.806748] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:542:DP-3]
<7> [177.806751] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:542:DP-3]
<7> [177.807006] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:542:DP-3] disconnected
<7> [177.807008] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:551:DP-4]
<7> [177.807011] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:551:DP-4]
<7> [177.807265] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:551:DP-4] disconnected
<7> [177.807268] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:560:DP-5]
<7> [177.807270] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:560:DP-5]
<7> [177.807524] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:560:DP-5] disconnected
<7> [177.807527] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:506:eDP-1] enabled? yes
<7> [177.807531] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:515:DP-1] enabled? no
<7> [177.807533] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:527:HDMI-A-1] enabled? no
<7> [177.807535] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:533:DP-2] enabled? no
<7> [177.807537] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:542:DP-3] enabled? no
<7> [177.807540] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:551:DP-4] enabled? no
<7> [177.807542] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:560:DP-5] enabled? no
<7> [177.807565] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [177.807579] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:506:eDP-1] found preferred mode: 3840x2400
<7> [177.807582] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3840x2400 config
<7> [177.807608] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:149:pipe A] desired mode 3840x2400 set (0,0)
<7> [177.811822] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [177.828561] Console: switching to colour frame buffer device 240x75
|