Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.35 seconds
Igt-Version 
IGT-Version: 2.3-g030b8e426 (x86_64) (Linux: 6.19.0-next-20260209-next-20260209-g132737e360b4+ x86_64)
Out 
Using IGT_SRANDOM=1770658282 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88812974d818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x684/0x9b0 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x32/0xa0 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x306/0x810 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.349s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.349s)
Dmesg
<6> [119.345818] Console: switching to colour dummy device 80x25
<6> [119.345925] [IGT] kms_pm_rpm: executing
<7> [119.349070] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [119.355020] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [119.355031] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [119.355340] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.356079] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.356768] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.357405] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [119.358128] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [119.358417] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [119.359328] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.360813] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.362446] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.363867] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.365649] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.367400] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.368954] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.370701] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.372291] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.373222] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [119.373939] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [119.374384] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [119.375046] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [119.375650] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [119.375661] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [119.380127] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [119.380700] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [119.380711] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [119.448288] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [119.452121] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.452135] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [119.452608] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [119.456220] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.456234] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [119.456794] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [119.457810] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [119.457824] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [119.458862] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [119.459394] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [119.460713] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.462626] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.463952] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [119.464525] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [119.465359] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.465911] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.467247] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [119.467800] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [119.468601] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [119.469377] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [119.470211] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [119.471595] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.473488] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.475469] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.477347] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.479185] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.480987] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.482717] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.483888] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [119.484973] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [119.485525] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [119.486377] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [119.486434] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [119.486446] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [119.491276] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [119.491316] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [119.491325] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [119.559678] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [119.563204] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.563215] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [119.563626] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [119.566952] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.566963] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [119.567369] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [119.567433] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [119.567442] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [119.568319] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [119.568896] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [119.569946] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.571575] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.573299] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.574937] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.576784] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.578632] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.580446] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.582342] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.583930] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [119.585102] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [119.586167] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [119.586660] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [119.587545] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [119.587743] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2]
<7> [119.587759] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [119.592512] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:122:DP-2] disconnected
<7> [119.592713] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1]
<7> [119.592729] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [119.661310] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [119.665963] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.665983] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [119.666723] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [119.671522] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [119.671548] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [119.672815] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:128:HDMI-A-1] disconnected
<7> [119.679818] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [119.680729] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [119.681491] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [119.682348] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [119.683918] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [120.684430] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [120.692108] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [120.716808] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [120.731382] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [120.733668] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [120.734373] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [120.734603] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [120.735227] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [120.735993] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [120.735918] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [120.736382] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [120.737425] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [120.737757] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [120.738583] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.740098] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.741480] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.743007] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.744603] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.746300] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.747937] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.749609] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.751174] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [120.752069] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [120.753088] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [120.753760] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [120.754941] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [120.759386] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [120.827261] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [120.831065] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.831077] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [120.831455] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [120.834799] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [120.834810] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [120.835541] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [120.855707] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [120.856316] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [120.857043] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [120.857724] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [120.858864] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [120.860092] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [120.867304] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [120.940639] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [120.992797] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [121.004690] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [121.011467] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [121.012235] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [121.012510] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [121.013339] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [121.014566] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [121.015253] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [121.016027] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [121.016453] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [121.016838] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [121.017856] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.019451] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.020901] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.022508] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.024110] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.025755] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.027518] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.029111] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.030616] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.031652] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [121.031613] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [121.031984] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [121.032253] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [121.032514] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [121.034320] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [121.035047] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [121.035674] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [121.036831] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [121.037666] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [121.039406] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [121.044086] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [121.044300] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [121.112662] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [121.116321] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.116332] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [121.116703] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [121.120327] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.120337] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [121.143908] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [121.144545] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [121.145106] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [121.145802] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [121.146731] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [121.147337] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [121.154597] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [121.259790] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [121.281062] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [121.283468] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [121.284491] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [121.284797] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [121.286643] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [121.289175] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<6> [121.291221] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [121.291762] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [121.292937] i915 0000:00:02.0: [drm:intel_lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [121.294611] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.296788] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.298679] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.300512] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.302491] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.304294] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.306128] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.307901] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.309600] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [121.310654] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [121.311861] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [121.312616] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [121.314306] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:122:DP-2]
<7> [121.318896] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:128:HDMI-A-1]
<7> [121.386664] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [121.390282] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.390293] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [121.390648] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [121.392699] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [121.393271] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [121.393710] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [121.394299] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [121.395398] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [121.395408] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [121.395910] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [121.396458] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [121.397144] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [121.398049] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [121.399138] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [121.399542] [IGT] kms_pm_rpm: exiting, ret=0
<6> [121.403060] Console: switching to colour frame buffer device 128x48
Created at 2026-02-10 00:34:29