Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.19 seconds
Igt-Version 
IGT-Version: 2.3-gf81ca2d72 (x86_64) (Linux: 6.19.0-rc8-next-20260205-next-20260205-g9845cf73f7db+ x86_64)
Out 
Using IGT_SRANDOM=1770303066 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88810c275818 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x20/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x13a1/0x1cb0 [i915]
     intel_atomic_commit+0x2e8/0x330 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x407/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1250/0x26e0
     do_syscall_64+0xdd/0x1470
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.187s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.187s)
Dmesg
<7> [105.306263] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [105.306596] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.306883] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [105.307201] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [105.307962] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [105.313045] Console: switching to colour dummy device 80x25
<6> [105.313111] [IGT] kms_pm_rpm: executing
<7> [105.323157] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [105.326788] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [105.326795] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [105.327001] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [105.331483] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [105.331790] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [105.331794] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [105.332457] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [105.332964] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [105.333538] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [105.334251] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [105.334739] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [105.335334] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [105.335648] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [105.335653] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [105.336076] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.336295] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [105.336714] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.336933] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.336937] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [105.337117] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [105.341427] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.341432] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [105.341627] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [105.341850] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [105.341855] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [105.346111] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [105.346127] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [105.346131] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [105.346955] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [105.347437] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [105.348027] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [105.348043] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [105.348046] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [105.348524] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.348710] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [105.349096] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.349357] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.349362] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [105.349558] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [105.353773] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.353777] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [105.353972] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [105.353995] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [105.353998] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [105.358301] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [105.358342] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2]
<7> [105.358346] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [105.359069] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [105.359564] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [105.360210] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:121:DP-2] disconnected
<7> [105.360277] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1]
<7> [105.360282] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [105.360712] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.360894] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [105.361324] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [105.361574] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.361578] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [105.361757] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [105.365915] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [105.365920] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [105.366114] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:127:HDMI-A-1] disconnected
<7> [105.434365] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [105.434810] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [105.435248] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [105.435646] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [105.436499] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [116.424834] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [116.430475] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [116.455161] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [116.463133] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [116.464903] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [116.464341] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [116.465297] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [116.466143] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [116.467214] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [116.467097] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [116.471786] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [116.472394] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [116.473857] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [116.474619] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [116.475834] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [116.476346] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [116.476545] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [116.476949] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [116.477204] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [116.477209] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [116.477407] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [116.481430] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [116.481435] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [116.481810] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [116.484170] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [116.484394] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [116.484599] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [116.484798] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [116.485501] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [116.485922] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [116.490490] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [116.583739] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [116.602517] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:57:pipe A]
<7> [116.614180] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [116.622860] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [116.624036] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [116.624552] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [116.625376] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [116.626222] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:82:pipe B]
<7> [116.626212] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [116.630750] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<7> [116.631355] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [116.632683] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [116.633606] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [116.634815] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [116.635287] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [116.635497] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [116.635887] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [116.636136] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [116.636143] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [116.636366] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [116.640595] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [116.640600] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [116.640952] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:107:pipe C]
<7> [116.645191] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [116.645438] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [116.645708] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [116.645943] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [116.646659] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [116.646873] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [116.650051] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [116.754186] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [116.764248] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [116.765717] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [116.766298] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [116.767568] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [116.768454] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [116.770954] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:121:DP-2]
<6> [116.771740] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [116.771614] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [116.773140] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [116.774273] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [116.775709] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:127:HDMI-A-1]
<7> [116.776180] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [116.776378] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [116.776779] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [116.777003] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [116.777009] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [116.777212] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [116.781425] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [116.781429] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [116.781859] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [116.781984] [IGT] kms_pm_rpm: exiting, ret=0
<6> [116.783400] Console: switching to colour frame buffer device 128x48
Created at 2026-02-06 10:02:27