Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

Detail	Value
Duration	1.42 seconds
Igt-Version	IGT-Version: 2.3-g2ac1ca079 (x86_64) (Linux: 6.19.0-rc6-next-20260120-next-20260120-g053966c344db+ x86_64)
Out	Using IGT_SRANDOM=1768929853 for randomisation Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888117db9818 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] intel_atomic_commit_tail+0x13a1/0x1cb0 [i915] intel_atomic_commit+0x2e8/0x330 [i915] drm_atomic_commit+0xaf/0xf0 drm_atomic_helper_set_config+0x82/0xd0 drm_mode_setcrtc+0x407/0xa10 drm_ioctl_kernel+0xb3/0x120 drm_ioctl+0x2d4/0x5a0 __x64_sys_ioctl+0xa5/0x100 x64_sys_call+0x1243/0x26b0 do_syscall_64+0x93/0x1470 entry_SYSCALL_64_after_hwframe+0x76/0x7e Subtest basic-rte: SUCCESS (1.420s) i915_runtime_pm_status: GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] ref_tracker: intel_runtime_pm@ffff888117db9818 has 1/1 users at track_intel_runtime_pm_wakeref+0x90/0xb0 [i915] __intel_runtime_pm_get+0x60/0x130 [i915] i915_display_rpm_get_raw+0x17/0x30 [i915] intel_display_rpm_get_raw+0x20/0x30 [i915] __intel_display_power_put_async+0x3a/0x1c0 [i915] __gt_park+0x175/0x240 [i915] ____intel_wakeref_put_last+0x2e/0xb0 [i915] __intel_wakeref_put_last+0x72/0x90 [i915] intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915] i915_forcewake_release+0x22/0x50 [i915] full_proxy_release+0x2e/0x50 __fput+0x10a/0x2f0 fput_close_sync+0x3d/0xa0 __x64_sys_close+0x3e/0x90 x64_sys_call+0x1b79/0x26b0 do_syscall_64+0x93/0x1470
Err	Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.420s)
Dmesg	<6> [69.520273] Console: switching to colour dummy device 80x25 <6> [69.520331] [IGT] kms_pm_rpm: executing <6> [69.522593] [IGT] kms_pm_rpm: starting subtest basic-rte <7> [69.522810] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [69.527536] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [69.527542] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [69.531773] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [69.532016] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [69.532020] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [69.536208] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [69.536444] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [69.536447] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [69.540679] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [69.540971] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [69.540974] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [69.545190] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [69.545203] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [69.545206] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [69.549391] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [69.549403] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [69.549406] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [69.553609] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [69.553625] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] <7> [69.553628] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [69.557809] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:388:HDMI-A-1] disconnected <7> [69.557842] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] <7> [69.557844] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [69.558614] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [69.558766] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [69.558903] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [69.562687] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:398:DP-1] disconnected <7> [69.562717] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] <7> [69.562719] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [69.567575] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:406:HDMI-A-2] disconnected <7> [69.670705] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [70.568454] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [70.574649] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [70.575989] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [70.576218] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [70.576505] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [70.576639] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [70.578514] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [70.603612] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [70.610476] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [70.610700] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [70.610867] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [70.611090] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.611289] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.611492] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.611685] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.611859] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [70.612363] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [70.613171] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [70.614858] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [70.616196] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [70.616332] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.622476] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [70.623700] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [70.623839] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [70.625033] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [70.628676] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [70.633554] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [70.638413] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [70.638605] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [70.638740] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [70.639539] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [70.640971] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [70.641080] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [70.658635] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [70.658861] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [70.659055] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.660429] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [70.660751] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [70.664152] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [70.665477] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [70.665712] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [70.665987] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [70.666121] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [70.668347] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [70.742118] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [70.754540] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [70.762344] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [70.763167] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [70.764079] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [70.765001] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.765908] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.766811] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.767688] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.768524] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [70.770104] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [70.770901] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [70.772413] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [70.774868] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [70.775659] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.786127] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [70.786435] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [70.786680] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [70.787464] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [70.788910] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <7> [70.789080] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [70.793108] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [70.797427] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [70.797532] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [70.815415] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [70.815813] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [70.816180] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.817734] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [70.818225] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [70.825315] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [70.826861] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [70.827701] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [70.828534] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [70.829134] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [70.833307] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [70.910381] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [70.918192] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [70.919020] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [70.919920] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [70.920834] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.921742] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.922692] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.923628] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [70.924492] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [70.926750] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [70.927579] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [70.929096] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [70.931619] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [70.932281] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [70.941377] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [70.941522] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [70.941909] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <6> [70.943942] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS <7> [70.944101] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:149:pipe A] <7> [70.946741] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <7> [70.951660] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2] <7> [70.956609] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [70.957614] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [70.959048] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:267:pipe B] <7> [70.959166] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:385:pipe C] <7> [71.045442] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [71.046389] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [71.047197] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [71.049131] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [71.049958] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [71.056119] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [71.057763] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [71.058701] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [71.059656] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [71.060457] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [71.067047] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [71.177395] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [71.186929] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [71.187755] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [71.188670] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [71.189641] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.190676] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.191601] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.192493] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [71.193372] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [71.194295] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0 <7> [71.195072] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [71.196034] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [71.198497] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [71.199137] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [71.211824] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [71.212209] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [71.212349] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [71.213086] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [71.214491] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0 <7> [71.214591] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:388:HDMI-A-1] <6> [71.214833] [IGT] kms_pm_rpm: exiting, ret=0 <7> [71.218823] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:398:DP-1] <6> [71.223450] Console: switching to colour frame buffer device 160x45 <7> [71.223985] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:406:HDMI-A-2]

Created at 2026-01-21 04:57:26