Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.29 seconds
Igt-Version 
IGT-Version: 2.3-gc45426aaf (x86_64) (Linux: 6.19.0-rc5-next-20260116-next-20260116-g46fe65a2c28e+ x86_64)
Out 
Using IGT_SRANDOM=1768572712 for randomisation
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.291s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.291s)
Dmesg
<6> [174.361696] Console: switching to colour dummy device 80x25
<6> [174.361921] [IGT] kms_force_connector_basic: executing
<7> [174.368880] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [174.370066] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [174.389967] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [174.391148] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:527:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [174.391158] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [174.391164] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [174.395370] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [174.395396] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [174.395399] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [174.399597] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [174.399633] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [174.399636] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [174.403821] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<6> [174.404010] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [174.404287] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:527:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [174.404292] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [174.404296] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [174.463773] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [174.469407] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [174.469420] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [174.469752] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [174.475187] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [174.475195] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [174.475451] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] status updated from disconnected to connected
<7> [174.475492] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] probed modes:
<7> [174.475496] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [174.475499] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [174.475502] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [174.475505] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [174.475508] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [174.475521] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [174.475565] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [174.475590] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [174.475594] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [174.535365] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [174.540994] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [174.541004] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [174.541170] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [174.546576] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [174.546580] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [174.546751] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] probed modes:
<7> [174.546755] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [174.546758] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [174.546761] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [174.546764] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [174.546767] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [174.547080] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:527:HDMI-A-1] EDID override set
<7> [174.547096] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [174.547099] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [174.547555] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:527:HDMI-A-1] ELD monitor IGT
<7> [174.547559] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:527:HDMI-A-1] ELD size 24, SAD count 0
<7> [174.608364] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [174.613959] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [174.614038] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 (STALE)
<7> [174.614045] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 (STALE)
<7> [174.614049] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] probed modes:
<7> [174.614052] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [174.614054] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [174.614057] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [174.614060] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [174.614062] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [174.614145] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:527:HDMI-A-1] EDID override reset
<7> [174.614235] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [174.614238] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [174.674355] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [174.680010] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [174.680025] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [174.680335] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [174.685834] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [174.685839] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [174.686072] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:527:HDMI-A-1] EDID changed, epoch counter 2
<7> [174.686136] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa (STALE)
<7> [174.686152] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 (STALE)
<7> [174.686162] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] probed modes:
<7> [174.686166] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [174.686171] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [174.686175] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [174.686179] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [174.686183] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [174.686329] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:527:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [174.686333] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [174.686336] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [174.690541] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] status updated from connected to disconnected
<7> [174.690549] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [174.690568] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [174.690608] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [174.690632] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [174.690636] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [174.694890] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<6> [174.695368] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [174.695810] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [174.696800] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:506:eDP-1] force updated from 0 to 0 or reprobing
<7> [174.696805] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1]
<7> [174.696809] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:506:eDP-1]
<7> [174.697393] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [174.697834] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [174.697972] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.698103] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.698248] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [174.698251] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [174.698253] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD monitor
<7> [174.698256] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD size 20, SAD count 0
<7> [174.698266] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] VRR capable: yes
<7> [174.698397] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [174.698527] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [174.699260] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1] probed modes:
<7> [174.699264] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [174.699285] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1]
<7> [174.699288] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:506:eDP-1]
<7> [174.699867] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [174.700286] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [174.700419] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.700549] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.700690] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [174.700693] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [174.700695] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD monitor
<7> [174.700697] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD size 20, SAD count 0
<7> [174.700704] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] VRR capable: yes
<7> [174.700860] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [174.700992] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [174.701714] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1] probed modes:
<7> [174.701717] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [174.701799] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:506:eDP-1] EDID override reset
<7> [174.701810] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1]
<7> [174.701814] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:506:eDP-1]
<7> [174.702364] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [174.702766] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [174.702941] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.703075] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.703220] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [174.703223] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [174.703225] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD monitor
<7> [174.703227] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD size 20, SAD count 0
<7> [174.703235] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] VRR capable: yes
<7> [174.703369] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [174.703503] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [174.704206] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1] probed modes:
<7> [174.704210] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [174.704280] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:515:DP-1] EDID override reset
<7> [174.704291] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:515:DP-1]
<7> [174.704294] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:515:DP-1]
<7> [174.708478] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:515:DP-1] disconnected
<7> [174.708581] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:527:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [174.708585] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [174.708588] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [174.712803] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [174.712824] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [174.712828] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [174.717021] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [174.717084] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:527:HDMI-A-1] EDID override reset
<7> [174.717094] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [174.717097] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [174.721301] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [174.721369] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:533:DP-2] EDID override reset
<7> [174.721379] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:533:DP-2]
<7> [174.721382] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:533:DP-2]
<7> [174.721649] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:533:DP-2] disconnected
<7> [174.721708] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:542:DP-3] EDID override reset
<7> [174.721717] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:542:DP-3]
<7> [174.721720] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:542:DP-3]
<7> [174.721977] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:542:DP-3] disconnected
<7> [174.722040] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:551:DP-4] EDID override reset
<7> [174.722050] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:551:DP-4]
<7> [174.722053] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:551:DP-4]
<7> [174.722295] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:551:DP-4] disconnected
<7> [174.722353] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:560:DP-5] EDID override reset
<7> [174.722363] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:560:DP-5]
<7> [174.722366] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:560:DP-5]
<7> [174.722607] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:560:DP-5] disconnected
<6> [174.722986] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [174.723400] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [174.741004] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]
<7> [174.741009] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [174.741063] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1]
<7> [174.741068] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:506:eDP-1]
<7> [174.741697] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [174.742209] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [174.742346] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.742480] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.742629] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [174.742632] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [174.742635] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD monitor
<7> [174.742637] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:506:eDP-1] ELD size 20, SAD count 0
<7> [174.742648] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] VRR capable: yes
<7> [174.742798] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [174.742927] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:506:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [174.743718] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:506:eDP-1] probed modes:
<7> [174.743722] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [174.743726] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:515:DP-1]
<7> [174.743729] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:515:DP-1]
<7> [174.747952] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:515:DP-1] disconnected
<7> [174.747956] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1]
<7> [174.747959] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:527:HDMI-A-1]
<7> [174.752182] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:527:HDMI-A-1] disconnected
<7> [174.752185] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:533:DP-2]
<7> [174.752188] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:533:DP-2]
<7> [174.752454] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:533:DP-2] disconnected
<7> [174.752457] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:542:DP-3]
<7> [174.752460] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:542:DP-3]
<7> [174.752706] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:542:DP-3] disconnected
<7> [174.752709] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:551:DP-4]
<7> [174.752711] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:551:DP-4]
<7> [174.752979] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:551:DP-4] disconnected
<7> [174.752982] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:560:DP-5]
<7> [174.752985] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:560:DP-5]
<7> [174.753227] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:560:DP-5] disconnected
<7> [174.753230] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:506:eDP-1] enabled? yes
<7> [174.753233] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:515:DP-1] enabled? no
<7> [174.753236] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:527:HDMI-A-1] enabled? no
<7> [174.753238] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:533:DP-2] enabled? no
<7> [174.753240] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:542:DP-3] enabled? no
<7> [174.753242] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:551:DP-4] enabled? no
<7> [174.753244] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:560:DP-5] enabled? no
<7> [174.753267] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [174.753277] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:506:eDP-1] found preferred mode: 3840x2400
<7> [174.753280] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3840x2400 config
<7> [174.753293] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:149:pipe A] desired mode 3840x2400 set (0,0)
<7> [174.757604] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [174.774294] Console: switching to colour frame buffer device 240x75
Created at 2026-01-16 19:17:38