Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 11.50 seconds
Igt-Version 
IGT-Version: 2.2-g9410b6926 (x86_64) (Linux: 6.18.0-next-20251210-next-20251210-g008d3547aae5+ x86_64)
Out 
Using IGT_SRANDOM=1765337627 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88811a031820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x1f/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x5c9/0x7f0 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x2e/0x70 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x2d8/0x7b0 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Subtest basic-rte: SUCCESS (11.502s)
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 2
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88811a031820 has 1/2 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x1f/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     __gt_park+0x175/0x240 [i915]
     ____intel_wakeref_put_last+0x2e/0xb0 [i915]
     __intel_wakeref_put_last+0x72/0x90 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x87/0x90 [i915]
     i915_forcewake_release+0x22/0x50 [i915]
     full_proxy_release+0x2e/0x50
     __fput+0x10a/0x2f0
     fput_close_sync+0x3d/0xa0
     __x64_sys_close+0x3e/0x90
     x64_sys_call+0x1b79/0x26b0
     do_syscall_64+0x93/0x1470

ref_tracker: intel_runtime_pm@ffff88811a031820 has 1/2 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get+0x1a/0x30 [i915]
     intel_display_rpm_get+0x1e/0x30 [i915]
     intel_display_power_get+0x22/0x70 [i915]
     i915_hpd_poll_init_work+0x1b2/0x2e0 [i915]
     process_one_work+0x22e/0x6b0
     worker_thread+0x1e8/0x3d0
     kthread+0x11f/0x250
     ret_from_fork+0x344/0x3a0
     ret_from_fork_asm+0x1a/0x30
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (11.502s)
Dmesg
<6> [114.991384] Console: switching to colour dummy device 80x25
<6> [114.991452] [IGT] kms_pm_rpm: executing
<6> [115.000711] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [115.000952] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [115.004436] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1]
<7> [115.004443] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [115.005290] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [115.005521] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.005721] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.005935] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.008871] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1] disconnected
<7> [115.009283] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [115.009289] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [115.009880] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.010409] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.010941] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [115.011941] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [115.012725] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [115.013592] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [115.013927] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1]
<7> [115.013950] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [115.014450] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [115.014627] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [115.015004] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [115.015229] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [115.015233] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [115.015401] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [115.019562] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [115.019566] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [115.019746] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1] disconnected
<7> [115.019991] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1]
<7> [115.019995] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [115.024291] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1] disconnected
<7> [115.024310] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [115.024314] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [115.025197] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [115.025977] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [115.026878] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [115.026893] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1]
<7> [115.026897] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [115.027316] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [115.027487] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [115.027858] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [115.028058] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [115.028061] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [115.028279] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [115.032539] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [115.032543] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [115.032717] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1] disconnected
<7> [115.032740] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1]
<7> [115.032743] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [115.037004] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1] disconnected
<7> [115.037044] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [115.037048] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [115.038107] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [115.038932] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [115.039685] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [115.039724] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1]
<7> [115.039728] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [115.040177] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [115.040364] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [115.040771] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [115.040999] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [115.041002] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [115.041206] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [115.045423] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [115.045428] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [115.045601] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1] disconnected
<7> [115.117422] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [115.118077] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.118725] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.119553] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.120843] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [126.094063] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [126.102942] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [126.126938] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [126.131896] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [126.132490] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [126.132804] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [126.133002] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:56:pipe A]
<7> [126.137423] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [126.138704] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [126.139339] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [126.140013] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [126.141620] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [126.142876] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [126.144860] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:80:pipe B]
<7> [126.144810] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [126.145265] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [126.145457] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [126.145880] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [126.146091] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [126.146095] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [126.146257] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [126.150502] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [126.150506] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [126.150816] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:104:pipe C]
<7> [126.251980] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [126.252375] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [126.252688] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [126.253010] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [126.253772] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [126.254433] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [126.258730] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [126.352435] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:56:pipe A]
<7> [126.364915] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [126.374968] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [126.375449] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [126.376096] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [126.376982] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [126.378128] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [126.378682] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:80:pipe B]
<7> [126.382996] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:104:pipe C]
<7> [126.383331] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [126.383836] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [126.385346] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [126.386563] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [126.388359] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [126.388805] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [126.389057] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [126.389419] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [126.389620] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [126.389625] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [126.389787] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [126.394017] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [126.394021] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [126.401952] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [126.402152] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [126.402336] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [126.402515] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [126.403176] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [126.403415] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [126.406871] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [126.494932] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [126.499829] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [126.500061] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [126.500312] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [126.500926] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [126.501492] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [126.503081] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [126.503315] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:56:pipe A]
<7> [126.504818] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [126.505190] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [126.505424] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:80:pipe B]
<7> [126.506561] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [126.507796] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [126.509894] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:104:pipe C]
<7> [126.511538] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [126.511974] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [126.512172] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [126.512571] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [126.512781] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [126.512785] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [126.513014] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [126.517530] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [126.517535] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [126.603987] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [126.604312] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [126.604586] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [126.604887] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [126.605737] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [126.606164] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [126.610876] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [126.725973] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [126.738252] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [126.738993] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [126.739685] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [126.740983] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [126.742022] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<7> [126.742044] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<6> [126.742398] [IGT] kms_pm_rpm: exiting, ret=0
<7> [126.746706] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [126.747085] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [126.748485] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [126.749727] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [126.751638] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<6> [126.751731] Console: switching to colour frame buffer device 128x48
<7> [126.752105] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [126.752273] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [126.752663] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [126.752910] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [126.752915] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [126.753103] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [126.757247] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [126.757251] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [126.760907] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [126.761208] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [126.761478] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [126.761743] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [126.762469] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2025-12-10 04:48:22