Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.18 seconds
Igt-Version 
IGT-Version: 2.2-g9410b6926 (x86_64) (Linux: 6.18.0-next-20251210-next-20251210-g008d3547aae5+ x86_64)
Out 
Using IGT_SRANDOM=1765337615 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88811a031820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x1f/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_dp_aux_xfer+0x5c9/0x7f0 [i915]
     intel_dp_aux_transfer+0xd4/0x330 [i915]
     drm_dp_dpcd_access+0xc3/0x160 [drm_display_helper]
     drm_dp_dpcd_read+0x87/0x160 [drm_display_helper]
     drm_dp_read_sink_count+0x2e/0x70 [drm_display_helper]
     intel_dp_get_dpcd+0x6f/0x160 [i915]
     intel_dp_detect+0x2d8/0x7b0 [i915]
     detect_connector_status+0x21/0x60
     drm_helper_probe_detect_ctx+0x75/0xe0
     drm_helper_probe_detect+0x7b/0x90
     intel_hotplug_detect_connector+0x4b/0x140 [i915]
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.182s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.182s)
Dmesg
<7> [103.344123] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [103.344358] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.344542] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.344722] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.345366] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [103.348446] Console: switching to colour dummy device 80x25
<6> [103.348512] [IGT] kms_pm_rpm: executing
<7> [103.357073] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [103.360522] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1]
<7> [103.360530] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [103.360719] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.365626] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1] disconnected
<7> [103.365950] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [103.365955] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [103.366601] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.367112] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.367655] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [103.368613] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.369382] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.370134] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [103.370449] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1]
<7> [103.370454] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [103.370913] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.371116] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.371561] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.371763] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.371767] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.371930] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.376226] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.376231] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.376407] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1] disconnected
<7> [103.376650] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1]
<7> [103.376654] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [103.380913] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1] disconnected
<7> [103.380929] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [103.380933] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [103.381994] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.382821] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.383731] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [103.383746] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1]
<7> [103.383750] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [103.384166] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.384336] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.384769] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.384968] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.384972] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.385174] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.389349] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.389353] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.389527] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1] disconnected
<7> [103.389550] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1]
<7> [103.389554] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [103.393813] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:106:DP-1] disconnected
<7> [103.393852] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [103.393855] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [103.394884] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.395674] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.396582] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [103.396621] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1]
<7> [103.396625] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [103.397136] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.397337] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.397773] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.397984] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.397988] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.398176] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.402340] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.402344] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.402519] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-1] disconnected
<7> [103.471226] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [103.471692] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.472230] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.472694] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.473640] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.454683] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [114.464618] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [114.489297] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [114.495743] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [114.496922] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.497403] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:56:pipe A]
<7> [114.497321] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [114.501924] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [114.502989] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [114.503587] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [114.504117] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [114.505660] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [114.506899] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [114.508929] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [114.509111] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:80:pipe B]
<7> [114.509403] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [114.509573] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [114.509948] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [114.510145] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [114.510150] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [114.510354] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [114.514522] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [114.514527] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [114.514924] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:104:pipe C]
<7> [114.613362] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [114.613887] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [114.614345] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.614846] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [114.615708] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.616562] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [114.624293] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [114.717334] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [114.739080] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:56:pipe A]
<7> [114.751289] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [114.758911] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [114.759373] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.759800] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [114.760493] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [114.761904] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [114.762535] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:80:pipe B]
<7> [114.766926] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [114.767333] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [114.767915] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:104:pipe C]
<7> [114.768760] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [114.770045] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [114.772114] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [114.772598] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [114.772769] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [114.773143] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [114.773403] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [114.773409] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [114.773661] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [114.778122] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [114.778128] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [114.785298] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [114.785501] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [114.785685] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.785865] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [114.786531] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.786846] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [114.790021] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [114.884344] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [114.895533] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [114.896290] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.897192] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:106:DP-1]
<7> [114.897185] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [114.898123] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [114.900057] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [114.903175] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [114.903648] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [114.905190] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [114.906420] i915 0000:00:02.0: [drm:drm_dp_dump_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [114.908533] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-1]
<7> [114.908991] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [114.909195] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [114.909707] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [114.909991] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [114.909998] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [114.910288] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [114.914858] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [114.914863] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [114.915429] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [114.915591] [IGT] kms_pm_rpm: exiting, ret=0
<6> [114.916959] Console: switching to colour frame buffer device 128x48
Created at 2025-12-10 04:48:22