Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json guc_logs0.tar i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.29 seconds
Igt-Version 
IGT-Version: 2.2-g9410b6926 (x86_64) (Linux: 6.18.0-next-20251210-next-20251210-g008d3547aae5+ x86_64)
Out 
Using IGT_SRANDOM=1765337612 for randomisation
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.290s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.290s)
Dmesg
<6> [177.086152] Console: switching to colour dummy device 80x25
<6> [177.086373] [IGT] kms_force_connector_basic: executing
<7> [177.098450] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [177.099660] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [177.108981] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [177.110140] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:523:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [177.110147] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [177.110151] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [177.114385] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [177.114408] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [177.114411] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [177.118628] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [177.118660] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [177.118663] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [177.122890] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<6> [177.123068] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [177.123328] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:523:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [177.123332] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [177.123335] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [177.181856] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [177.187813] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.187837] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.188097] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [177.193627] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.193636] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [177.193853] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] status updated from disconnected to connected
<7> [177.193869] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [177.193944] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [177.193997] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] probed modes:
<7> [177.194002] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [177.194006] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [177.194010] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [177.194013] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [177.194017] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [177.194049] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [177.194053] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [177.252383] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [177.258037] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.258047] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.258280] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [177.263704] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.263709] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [177.263882] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] probed modes:
<7> [177.263886] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [177.263888] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [177.263891] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [177.263893] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [177.263895] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [177.264193] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:523:HDMI-A-1] EDID override set
<7> [177.264208] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [177.264211] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [177.264756] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:523:HDMI-A-1] ELD monitor IGT
<7> [177.264759] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:523:HDMI-A-1] ELD size 24, SAD count 0
<7> [177.325392] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [177.330973] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [177.331070] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 (STALE)
<7> [177.331079] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 (STALE)
<7> [177.331084] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] probed modes:
<7> [177.331088] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [177.331092] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [177.331096] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [177.331099] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [177.331102] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [177.331214] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:523:HDMI-A-1] EDID override reset
<7> [177.331368] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [177.331372] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [177.392837] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [177.398511] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.398517] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [177.398648] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [177.404036] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [177.404042] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [177.404225] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:523:HDMI-A-1] EDID changed, epoch counter 2
<7> [177.404275] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa (STALE)
<7> [177.404283] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 (STALE)
<7> [177.404291] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] probed modes:
<7> [177.404295] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [177.404298] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [177.404302] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [177.404305] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [177.404308] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [177.404428] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:523:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [177.404432] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [177.404435] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [177.408625] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] status updated from connected to disconnected
<7> [177.408632] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [177.408638] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [177.408668] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [177.408699] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [177.408702] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [177.412953] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<6> [177.413145] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [177.413506] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [177.414596] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:502:eDP-1] force updated from 0 to 0 or reprobing
<7> [177.414601] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1]
<7> [177.414604] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:502:eDP-1]
<7> [177.415268] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [177.415702] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [177.415852] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.415983] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.416124] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [177.416127] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [177.416130] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD monitor
<7> [177.416132] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD size 20, SAD count 0
<7> [177.416143] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] VRR capable: yes
<7> [177.416276] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [177.416403] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [177.417542] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1] probed modes:
<7> [177.417546] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [177.417567] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1]
<7> [177.417570] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:502:eDP-1]
<7> [177.418222] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [177.418647] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [177.418777] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.418921] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.419061] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [177.419064] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [177.419066] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD monitor
<7> [177.419068] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD size 20, SAD count 0
<7> [177.419077] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] VRR capable: yes
<7> [177.419207] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [177.419332] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [177.420080] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1] probed modes:
<7> [177.420083] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [177.420154] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:502:eDP-1] EDID override reset
<7> [177.420165] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1]
<7> [177.420168] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:502:eDP-1]
<7> [177.420857] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [177.421261] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [177.421387] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.421512] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.421648] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [177.421651] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [177.421653] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD monitor
<7> [177.421655] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD size 20, SAD count 0
<7> [177.421662] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] VRR capable: yes
<7> [177.421802] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [177.421933] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [177.422681] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1] probed modes:
<7> [177.422685] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [177.422756] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:511:DP-1] EDID override reset
<7> [177.422766] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:511:DP-1]
<7> [177.422769] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:511:DP-1]
<7> [177.427022] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:511:DP-1] disconnected
<7> [177.427121] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:523:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [177.427124] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [177.427127] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [177.431352] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [177.431371] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [177.431373] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [177.435589] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [177.435650] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:523:HDMI-A-1] EDID override reset
<7> [177.435660] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [177.435663] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [177.439861] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [177.439925] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:529:DP-2] EDID override reset
<7> [177.439934] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:DP-2]
<7> [177.439937] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:529:DP-2]
<7> [177.440202] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:DP-2] disconnected
<7> [177.440260] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:538:DP-3] EDID override reset
<7> [177.440269] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:538:DP-3]
<7> [177.440272] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:538:DP-3]
<7> [177.440525] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:538:DP-3] disconnected
<7> [177.440581] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:547:DP-4] EDID override reset
<7> [177.440589] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:547:DP-4]
<7> [177.440592] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:547:DP-4]
<7> [177.440852] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:547:DP-4] disconnected
<7> [177.440914] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:556:DP-5] EDID override reset
<7> [177.440923] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:556:DP-5]
<7> [177.440926] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:556:DP-5]
<7> [177.441166] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:556:DP-5] disconnected
<6> [177.441535] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [177.441985] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [177.459702] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]
<7> [177.459706] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [177.459761] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1]
<7> [177.459766] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:502:eDP-1]
<7> [177.460490] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [177.460938] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [177.461072] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.461208] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [177.461349] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [177.461352] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [177.461354] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD monitor
<7> [177.461356] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD size 20, SAD count 0
<7> [177.461366] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] VRR capable: yes
<7> [177.461492] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [177.461616] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [177.462442] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1] probed modes:
<7> [177.462445] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [177.462449] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:511:DP-1]
<7> [177.462452] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:511:DP-1]
<7> [177.466663] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:511:DP-1] disconnected
<7> [177.466675] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [177.466681] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [177.471004] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [177.471009] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:DP-2]
<7> [177.471012] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:529:DP-2]
<7> [177.471285] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:DP-2] disconnected
<7> [177.471288] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:538:DP-3]
<7> [177.471291] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:538:DP-3]
<7> [177.471552] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:538:DP-3] disconnected
<7> [177.471554] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:547:DP-4]
<7> [177.471557] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:547:DP-4]
<7> [177.471837] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:547:DP-4] disconnected
<7> [177.471841] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:556:DP-5]
<7> [177.471844] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:556:DP-5]
<7> [177.472102] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:556:DP-5] disconnected
<7> [177.472105] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:502:eDP-1] enabled? yes
<7> [177.472108] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:511:DP-1] enabled? no
<7> [177.472110] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:523:HDMI-A-1] enabled? no
<7> [177.472112] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:529:DP-2] enabled? no
<7> [177.472114] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:538:DP-3] enabled? no
<7> [177.472116] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:547:DP-4] enabled? no
<7> [177.472118] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:556:DP-5] enabled? no
<7> [177.472142] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [177.472155] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:502:eDP-1] found preferred mode: 3840x2400
<7> [177.472157] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3840x2400 config
<7> [177.472182] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:148:pipe A] desired mode 3840x2400 set (0,0)
<7> [177.476199] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [177.492955] Console: switching to colour frame buffer device 240x75
Created at 2025-12-10 04:48:20