Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.22 seconds
Igt-Version 
IGT-Version: 2.2-gb1ad5288c (x86_64) (Linux: 6.18.0-next-20251209-next-20251209-gc75caf76ed86+ x86_64)
Out 
Using IGT_SRANDOM=1765254545 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: intel_runtime_pm@ffff88810aea5820 has 1/1 users at
     track_intel_runtime_pm_wakeref+0x90/0xb0 [i915]
     __intel_runtime_pm_get+0x60/0x130 [i915]
     i915_display_rpm_get_raw+0x17/0x30 [i915]
     intel_display_rpm_get_raw+0x1f/0x30 [i915]
     __intel_display_power_put_async+0x3a/0x1c0 [i915]
     intel_atomic_commit_tail+0x136b/0x1c50 [i915]
     intel_atomic_commit+0x2e8/0x330 [i915]
     drm_atomic_commit+0xaf/0xf0
     drm_atomic_helper_set_config+0x82/0xd0
     drm_mode_setcrtc+0x407/0xa10
     drm_ioctl_kernel+0xb3/0x120
     drm_ioctl+0x2d4/0x5a0
     __x64_sys_ioctl+0xa5/0x100
     x64_sys_call+0x1243/0x26b0
     do_syscall_64+0x93/0x1470
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.217s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.217s)
Dmesg
<6> [67.734745] Console: switching to colour dummy device 80x25
<6> [67.734793] [IGT] kms_pm_rpm: executing
<7> [67.736639] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [67.740988] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:385:HDMI-A-1]
<7> [67.740995] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:385:HDMI-A-1]
<7> [67.745194] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:385:HDMI-A-1] disconnected
<7> [67.745438] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:395:DP-1]
<7> [67.745442] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:395:DP-1]
<7> [67.749650] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:395:DP-1] disconnected
<7> [67.749886] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:403:HDMI-A-2]
<7> [67.749889] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:403:HDMI-A-2]
<7> [67.754232] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:403:HDMI-A-2] disconnected
<7> [67.754513] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:385:HDMI-A-1]
<7> [67.754515] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:385:HDMI-A-1]
<7> [67.758736] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:385:HDMI-A-1] disconnected
<7> [67.758748] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:395:DP-1]
<7> [67.758751] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:395:DP-1]
<7> [67.762951] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:395:DP-1] disconnected
<7> [67.762962] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:403:HDMI-A-2]
<7> [67.762965] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:403:HDMI-A-2]
<7> [67.767186] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:403:HDMI-A-2] disconnected
<7> [67.767202] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:385:HDMI-A-1]
<7> [67.767205] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:385:HDMI-A-1]
<7> [67.771423] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:385:HDMI-A-1] disconnected
<7> [67.771454] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:395:DP-1]
<7> [67.771456] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:395:DP-1]
<7> [67.775640] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:395:DP-1] disconnected
<7> [67.775670] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:403:HDMI-A-2]
<7> [67.775673] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:403:HDMI-A-2]
<7> [67.779850] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:403:HDMI-A-2] disconnected
<7> [67.786141] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [67.786293] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [67.786428] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [67.787696] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [68.784614] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [68.789816] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [68.791153] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [68.791534] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [68.791822] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [68.791962] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [68.793768] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [68.818994] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [68.826728] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [68.827584] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [68.828449] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [68.829458] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [68.830402] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [68.831342] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [68.832269] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [68.833177] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [68.834948] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [68.835644] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [68.836166] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [68.836851] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [68.836986] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [68.845553] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [68.846882] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [68.847061] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:148:pipe A]
<7> [68.851687] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [68.853052] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [68.853489] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [68.853784] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [68.853922] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [68.855582] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [68.880015] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [68.887779] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [68.888615] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [68.889461] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [68.890407] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [68.891348] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [68.892250] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [68.893158] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [68.894029] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [68.895658] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [68.896356] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [68.897732] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [68.899763] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [68.900323] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [68.910562] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [68.910783] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [68.910921] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [68.911809] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [68.913233] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:265:pipe B]
<7> [68.913190] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:385:HDMI-A-1]
<7> [68.917555] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:395:DP-1]
<7> [68.921834] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:403:HDMI-A-2]
<7> [68.926222] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:382:pipe C]
<7> [68.943681] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [68.943831] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [68.943967] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [68.945273] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [68.946257] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [68.953284] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [68.954991] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [68.955754] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [68.956574] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [68.957204] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [68.962255] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [69.027884] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [69.056885] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:148:pipe A]
<7> [69.068931] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [69.072642] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [69.072973] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [69.073303] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [69.073674] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [69.074006] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [69.074328] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [69.074660] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [69.074974] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [69.075779] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [69.076042] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [69.076659] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [69.077499] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [69.077700] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [69.085100] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [69.085197] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [69.085357] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [69.086322] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [69.087832] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:385:HDMI-A-1]
<7> [69.088068] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:265:pipe B]
<7> [69.092311] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:395:DP-1]
<7> [69.092472] i915 0000:00:02.0: [drm:drm_mode_setcrtc] [CRTC:382:pipe C]
<7> [69.096618] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:403:HDMI-A-2]
<7> [69.113762] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [69.113913] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [69.114048] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [69.115355] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [69.115685] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [69.120268] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [69.121670] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [69.122490] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [69.123082] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [69.123457] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [69.127641] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [69.210210] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [69.217768] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [69.218594] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [69.219503] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [69.220433] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [69.221376] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [69.222268] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [69.223144] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [69.223999] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [69.225235] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Current CDCLK 12000 kHz, VCO 0 kHz, ref 24000 kHz, bypass 12000 kHz, voltage level 0
<7> [69.226031] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [69.226953] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [69.229355] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [69.230142] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [69.243034] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [69.243279] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [69.243450] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:385:HDMI-A-1]
<6> [69.246860] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [69.248121] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:395:DP-1]
<7> [69.252986] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:403:HDMI-A-2]
<7> [69.258188] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [69.258968] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [69.260393] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [69.260501] [IGT] kms_pm_rpm: exiting, ret=0
<6> [69.261501] Console: switching to colour frame buffer device 160x45
Created at 2025-12-09 06:27:03