Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline i915_display_info0 igt_runner0 run0 runtimes0 results0.json i915_display_info_post_exec0 boot0 dmesg0

DetailValue
Duration 0.29 seconds
Igt-Version 
IGT-Version: 2.2-gb1ad5288c (x86_64) (Linux: 6.18.0-next-20251208-next-20251208-g82bcd04d124a+ x86_64)
Out 
Using IGT_SRANDOM=1765226745 for randomisation
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.288s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.288s)
Dmesg
<6> [173.986718] Console: switching to colour dummy device 80x25
<6> [173.986929] [IGT] kms_force_connector_basic: executing
<7> [173.999952] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [174.002529] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [174.028242] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [174.030435] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:523:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [174.030448] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [174.030455] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [174.034784] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [174.034809] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [174.034812] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [174.039045] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [174.039082] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [174.039084] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [174.043290] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<6> [174.043457] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [174.043716] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:523:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [174.043720] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [174.043723] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [174.102943] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [174.108888] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [174.108936] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [174.109299] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [174.115028] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [174.115033] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [174.115158] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] status updated from disconnected to connected
<7> [174.115173] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [174.115246] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [174.115293] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] probed modes:
<7> [174.115298] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [174.115302] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [174.115306] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [174.115310] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [174.115313] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [174.115346] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [174.115350] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [174.174479] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [174.180186] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [174.180195] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [174.180430] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [174.185933] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [174.185938] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [174.186090] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] probed modes:
<7> [174.186094] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [174.186096] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [174.186099] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [174.186101] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [174.186103] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [174.186464] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:523:HDMI-A-1] EDID override set
<7> [174.186480] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [174.186483] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [174.187080] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:523:HDMI-A-1] ELD monitor IGT
<7> [174.187084] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:523:HDMI-A-1] ELD size 24, SAD count 0
<7> [174.245475] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [174.251113] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [174.251250] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 (STALE)
<7> [174.251261] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 (STALE)
<7> [174.251267] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] probed modes:
<7> [174.251271] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [174.251276] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [174.251279] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [174.251283] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [174.251287] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [174.251388] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:523:HDMI-A-1] EDID override reset
<7> [174.251587] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [174.251589] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [174.311936] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [174.317596] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [174.317602] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [174.317737] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [174.323124] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [174.323128] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [174.323257] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:523:HDMI-A-1] EDID changed, epoch counter 2
<7> [174.323303] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa (STALE)
<7> [174.323310] i915 0000:00:02.0: [drm:drm_mode_prune_invalid] Rejected mode: "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5 (STALE)
<7> [174.323315] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] probed modes:
<7> [174.323318] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [174.323320] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [174.323322] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [174.323325] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [174.323327] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [174.323435] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:523:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [174.323439] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [174.323441] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [174.327679] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] status updated from connected to disconnected
<7> [174.327688] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [174.327695] i915 0000:00:02.0: [drm:drm_sysfs_hotplug_event] generating hotplug event
<7> [174.327737] i915 0000:00:02.0: [drm:drm_client_hotplug] fbdev: ret=0
<7> [174.327775] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [174.327778] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [174.332037] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<6> [174.332249] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [174.332663] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [174.333756] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:502:eDP-1] force updated from 0 to 0 or reprobing
<7> [174.333760] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1]
<7> [174.333763] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:502:eDP-1]
<7> [174.334414] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [174.334835] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [174.334988] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.335117] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.335252] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [174.335255] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [174.335257] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD monitor
<7> [174.335259] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD size 20, SAD count 0
<7> [174.335270] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] VRR capable: yes
<7> [174.335390] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [174.335509] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [174.336271] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1] probed modes:
<7> [174.336274] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [174.336295] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1]
<7> [174.336298] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:502:eDP-1]
<7> [174.336932] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [174.337344] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [174.337471] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.337593] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.337724] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [174.337727] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [174.337729] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD monitor
<7> [174.337731] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD size 20, SAD count 0
<7> [174.337738] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] VRR capable: yes
<7> [174.337858] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [174.337993] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [174.338941] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1] probed modes:
<7> [174.338944] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [174.339013] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:502:eDP-1] EDID override reset
<7> [174.339024] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1]
<7> [174.339027] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:502:eDP-1]
<7> [174.339649] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [174.340046] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [174.340167] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.340287] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.340419] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [174.340422] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [174.340424] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD monitor
<7> [174.340426] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD size 20, SAD count 0
<7> [174.340433] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] VRR capable: yes
<7> [174.340553] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [174.340675] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [174.341396] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1] probed modes:
<7> [174.341398] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [174.341471] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:511:DP-1] EDID override reset
<7> [174.341482] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:511:DP-1]
<7> [174.341485] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:511:DP-1]
<7> [174.345660] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:511:DP-1] disconnected
<7> [174.345757] i915 0000:00:02.0: [drm:status_store] [CONNECTOR:523:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [174.345760] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [174.345763] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [174.350001] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [174.350020] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [174.350023] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [174.354218] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [174.354280] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:523:HDMI-A-1] EDID override reset
<7> [174.354290] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [174.354293] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [174.358471] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [174.358541] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:529:DP-2] EDID override reset
<7> [174.358551] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:DP-2]
<7> [174.358553] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:529:DP-2]
<7> [174.358809] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:DP-2] disconnected
<7> [174.358869] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:538:DP-3] EDID override reset
<7> [174.358879] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:538:DP-3]
<7> [174.358882] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:538:DP-3]
<7> [174.359138] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:538:DP-3] disconnected
<7> [174.359201] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:547:DP-4] EDID override reset
<7> [174.359210] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:547:DP-4]
<7> [174.359212] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:547:DP-4]
<7> [174.359446] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:547:DP-4] disconnected
<7> [174.359506] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:556:DP-5] EDID override reset
<7> [174.359515] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:556:DP-5]
<7> [174.359517] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:556:DP-5]
<7> [174.359743] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:556:DP-5] disconnected
<6> [174.360128] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [174.360367] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [174.378139] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event]
<7> [174.378144] i915 0000:00:02.0: [drm:drm_client_modeset_probe]
<7> [174.378205] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1]
<7> [174.378210] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:502:eDP-1]
<7> [174.379057] i915 0000:00:02.0: [drm:intel_dp_read_dsc_dpcd [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [174.380012] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 675000, 810000
<7> [174.380453] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.380977] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000
<7> [174.381384] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Supported Monitor Refresh rate range is 40 Hz - 60 Hz
<7> [174.381390] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.
<7> [174.381394] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD monitor
<7> [174.381398] i915 0000:00:02.0: [drm:update_display_info.part.0] [CONNECTOR:502:eDP-1] ELD size 20, SAD count 0
<7> [174.381413] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] VRR capable: yes
<7> [174.381650] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [174.381884] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:502:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [174.382925] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:502:eDP-1] probed modes:
<7> [174.382928] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] Probed mode: "3840x2400": 60 596200 3840 3888 3920 4000 2400 2403 2408 2484 0x48 0xa
<7> [174.382933] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:511:DP-1]
<7> [174.382936] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:511:DP-1]
<7> [174.387176] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:511:DP-1] disconnected
<7> [174.387180] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1]
<7> [174.387183] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:523:HDMI-A-1]
<7> [174.391415] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:523:HDMI-A-1] disconnected
<7> [174.391420] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:DP-2]
<7> [174.391423] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:529:DP-2]
<7> [174.391727] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:529:DP-2] disconnected
<7> [174.391731] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:538:DP-3]
<7> [174.391733] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:538:DP-3]
<7> [174.392004] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:538:DP-3] disconnected
<7> [174.392008] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:547:DP-4]
<7> [174.392011] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:547:DP-4]
<7> [174.392263] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:547:DP-4] disconnected
<7> [174.392266] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:556:DP-5]
<7> [174.392268] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:556:DP-5]
<7> [174.392530] i915 0000:00:02.0: [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:556:DP-5] disconnected
<7> [174.392533] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:502:eDP-1] enabled? yes
<7> [174.392536] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:511:DP-1] enabled? no
<7> [174.392539] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:523:HDMI-A-1] enabled? no
<7> [174.392541] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:529:DP-2] enabled? no
<7> [174.392543] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:538:DP-3] enabled? no
<7> [174.392545] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:547:DP-4] enabled? no
<7> [174.392547] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:556:DP-5] enabled? no
<7> [174.392575] i915 0000:00:02.0: [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [174.392586] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CONNECTOR:502:eDP-1] found preferred mode: 3840x2400
<7> [174.392589] i915 0000:00:02.0: [drm:drm_client_modeset_probe] picking CRTCs for 3840x2400 config
<7> [174.392607] i915 0000:00:02.0: [drm:drm_client_modeset_probe] [CRTC:148:pipe A] desired mode 3840x2400 set (0,0)
<7> [174.394638] i915 0000:00:02.0: [drm:drm_client_dev_restore] fbdev: ret=0
<6> [174.411327] Console: switching to colour frame buffer device 240x75
Created at 2025-12-09 00:39:39