Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 1.52 seconds
Igt-Version 
IGT-Version: 1.28-g86712f2ef (x86_64) (Linux: 6.9.0-linus-v6.9-ga38297e3fb01+ x86_64)
Out 
Using IGT_SRANDOM=1715548897 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff88810de5b3d8 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     intel_atomic_commit_tail+0xb0b/0xfa0 [i915]
     intel_atomic_commit+0x330/0x380 [i915]
     drm_atomic_commit+0x9a/0xd0
     drm_atomic_helper_set_config+0x77/0xc0
     drm_mode_setcrtc+0x1f4/0x740
     drm_ioctl_kernel+0xa8/0x100
     drm_ioctl+0x222/0x430
     __x64_sys_ioctl+0x79/0xb0
     do_syscall_64+0x69/0x140
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Subtest basic-rte: SUCCESS (1.520s)
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff88810de5b3d8 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     __gt_park+0x154/0x210 [i915]
     ____intel_wakeref_put_last+0x1d/0x80 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x76/0x80 [i915]
     i915_forcewake_release+0x1d/0x40 [i915]
     full_proxy_release+0x39/0xa0
     __fput+0xa1/0x2d0
     __x64_sys_close+0x38/0x80
     do_syscall_64+0x69/0x140
     entry_SYSCALL_64_after_hwframe+0x76/0x7e
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (1.520s)
Dmesg
<6> [90.252950] Console: switching to colour dummy device 80x25
<6> [90.253005] [IGT] kms_pm_rpm: executing
<6> [90.256127] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [90.256191] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [90.260976] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [90.260984] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [90.261119] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.261757] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.261868] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [90.262618] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.263147] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.263151] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.263268] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [90.278918] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.278923] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [90.279046] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.279188] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [90.279679] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [90.279685] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [90.279856] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.280864] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.280990] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.281598] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.282121] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.282125] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.282236] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.296957] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.296962] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.297078] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.297205] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [90.297704] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [90.297710] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [90.297856] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.303101] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [90.303436] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [90.303442] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [90.304419] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.304565] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [90.305181] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.305678] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.305682] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.305842] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [90.321545] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.321550] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [90.321671] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [90.321694] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [90.321699] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [90.322731] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.322861] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.323166] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.323605] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.323610] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.323753] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.339957] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.339962] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.340110] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [90.340130] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [90.340135] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [90.344833] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [90.344864] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [90.344869] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [90.345844] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.345955] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [90.346254] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.346695] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.346699] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.346831] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [90.363070] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.363075] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [90.363197] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [90.363264] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [90.363269] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [90.364244] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.364390] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.364720] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.365145] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.365148] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.365292] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.381041] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.381045] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.381166] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [90.381234] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [90.381239] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [90.385938] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [90.490902] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.388092] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.391903] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [91.404346] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [91.430393] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.447304] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [91.448912] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.449305] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.450158] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [91.450546] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.451376] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.452935] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [91.453605] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [91.453606] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [91.454426] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [91.454797] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [91.455328] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [91.455730] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.455743] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.456044] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [91.459415] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.459420] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [91.459607] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [91.459967] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.460077] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.460368] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.460518] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.460522] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.460631] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.463478] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.463482] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.463654] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [91.486659] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.486803] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.486939] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.487519] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.487698] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.489104] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [91.492615] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [91.569317] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [91.582060] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.600158] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [91.601347] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.601998] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.602815] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.604027] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.605805] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [91.606648] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [91.606912] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [91.607606] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [91.608911] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [91.609687] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.609711] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.610527] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [91.616544] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.616573] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [91.617328] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [91.618421] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.619213] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.620202] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.621285] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.621308] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.621953] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.623664] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.624453] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.624964] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.636595] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.636607] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.637121] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.637751] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.638630] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [91.638638] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [91.661595] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.661791] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.661978] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.662616] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.662832] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.663840] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [91.666878] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [91.756774] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.774011] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [91.774565] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.774697] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.774827] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.775239] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [91.776187] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [91.776211] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [91.776399] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [91.776637] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [91.776768] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [91.776886] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [91.777191] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [91.777331] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.777336] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.777467] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [91.780343] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.780349] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [91.780653] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [91.780998] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.781114] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.781410] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.781563] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.781567] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.781710] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.784581] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.784586] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.784880] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [91.784879] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [91.900550] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.900862] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.901137] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.901884] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.902242] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.903810] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [91.910727] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [92.020618] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [92.044646] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [92.047760] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [92.049380] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [92.050229] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [92.051454] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [92.052688] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [92.054208] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [92.055087] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [92.055369] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [92.056053] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [92.057044] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [92.057800] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [92.057825] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [92.058608] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [92.063605] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [92.063633] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [92.064269] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [92.065066] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.065556] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [92.066290] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.066797] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.066817] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [92.067365] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [92.068547] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [92.069289] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [92.069832] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [92.070349] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [92.073956] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.073972] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [92.074320] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [92.079764] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [92.248796] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [92.248944] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [92.249402] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [92.250116] [IGT] kms_pm_rpm: exiting, ret=0
<6> [92.251251] Console: switching to colour frame buffer device 128x48
Created at 2024-05-12 22:37:22