Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 1.50 seconds
Igt-Version 
IGT-Version: 1.28-g86173d01d (x86_64) (Linux: 6.8.0-linus-v6.8-ge8f897f4afef+ x86_64)
Out 
Using IGT_SRANDOM=1710105473 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff88810fa2b4b0 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     intel_atomic_commit_tail+0xaef/0xf80 [i915]
     intel_atomic_commit+0x321/0x370 [i915]
     drm_atomic_commit+0x92/0xc0
     drm_atomic_helper_set_config+0x77/0xc0
     drm_mode_setcrtc+0x1f4/0x740
     drm_ioctl_kernel+0xa8/0x100
     drm_ioctl+0x223/0x430
     __x64_sys_ioctl+0x79/0xb0
     do_syscall_64+0x6f/0x140
     entry_SYSCALL_64_after_hwframe+0x6e/0x76
Subtest basic-rte: SUCCESS (1.501s)
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff88810fa2b4b0 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     __gt_park+0x154/0x210 [i915]
     ____intel_wakeref_put_last+0x1d/0x80 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x76/0x80 [i915]
     i915_forcewake_release+0x1d/0x40 [i915]
     full_proxy_release+0x39/0xa0
     __fput+0xa1/0x2d0
     __x64_sys_close+0x39/0x80
     do_syscall_64+0x6f/0x140
     entry_SYSCALL_64_after_hwframe+0x6e/0x76
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (1.501s)
Dmesg
<6> [94.845846] Console: switching to colour dummy device 80x25
<6> [94.845905] [IGT] kms_pm_rpm: executing
<6> [94.848332] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [94.848404] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [94.853632] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [94.853640] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [94.853771] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [94.854429] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [94.854564] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [94.855154] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [94.855684] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [94.855691] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.855845] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [94.870493] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [94.870498] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [94.870617] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [94.870744] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [94.871393] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [94.871399] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [94.871517] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [94.872149] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [94.872257] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [94.872546] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [94.872958] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.872962] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.873067] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [94.887253] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.887258] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [94.887375] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [94.887503] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [94.887975] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [94.887980] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [94.888117] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [94.888610] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [94.888971] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [94.888976] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [94.889983] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [94.890139] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [94.890432] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [94.890747] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [94.890751] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.890877] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [94.907190] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [94.907196] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [94.907314] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [94.907334] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [94.907338] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [94.907947] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [94.908052] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [94.908662] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [94.909212] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.909219] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.909327] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [94.926039] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.926045] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [94.926225] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [94.926258] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [94.926264] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [94.926746] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [94.926776] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [94.926780] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [94.927777] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [94.927909] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [94.928553] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [94.929092] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [94.929097] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.929235] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [94.945540] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [94.945546] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [94.945666] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [94.945723] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [94.945727] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [94.946685] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [94.946823] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [94.947126] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [94.947570] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.947576] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.947728] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [94.963959] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.963965] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [94.964118] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [94.964187] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [94.964193] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [94.964663] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [95.071303] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [95.966487] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [95.968484] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [95.986303] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [96.012023] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [96.029547] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [96.030663] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [96.032698] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [96.032438] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [96.033449] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [96.034282] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [96.035459] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [96.036230] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [96.036274] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [96.037027] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [96.037430] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [96.038043] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [96.038486] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [96.038499] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [96.038791] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [96.042395] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [96.042409] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [96.043116] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [96.043719] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [96.044002] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [96.044438] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [96.044712] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [96.044722] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [96.044980] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [96.048282] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [96.048293] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [96.048546] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [96.066991] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [96.067211] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [96.067421] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [96.068086] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [96.068359] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [96.070247] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [96.073934] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [96.150051] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [96.162697] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [96.180633] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [96.181739] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [96.182325] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [96.183041] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [96.184057] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [96.185599] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [96.186363] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [96.186624] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [96.187248] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [96.188225] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [96.188938] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [96.188965] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [96.189548] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [96.194623] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [96.194653] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [96.195530] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [96.196580] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [96.197240] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [96.198091] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [96.198751] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [96.198775] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [96.199426] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [96.203007] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [96.203988] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [96.204797] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [96.206210] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [96.206248] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [96.208178] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [96.209097] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [96.210289] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [96.210306] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [96.228966] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [96.229223] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [96.229468] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [96.230170] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [96.230454] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [96.231949] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [96.235859] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [96.324447] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [96.341525] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [96.343159] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [96.343696] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [96.344515] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [96.345550] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [96.347552] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<6> [96.349506] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [96.349623] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [96.349406] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [96.350056] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [96.350941] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [96.351900] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [96.351938] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [96.352594] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [96.357643] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [96.357675] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [96.358418] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [96.359406] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [96.360062] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [96.360981] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [96.361648] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [96.361673] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [96.362306] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [96.367469] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [96.367509] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [96.368316] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [96.369559] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [96.370084] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [96.472995] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [96.473853] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [96.474604] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [96.475841] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [96.476693] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [96.478520] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [96.488907] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [96.603545] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [96.625496] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [96.628466] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [96.629972] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [96.630651] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [96.631867] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [96.633007] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [96.634113] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [96.634727] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [96.634879] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [96.635308] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [96.635920] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [96.636374] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [96.636392] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [96.636846] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [96.640631] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [96.640646] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [96.641032] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [96.641632] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [96.641976] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [96.642488] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [96.642876] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [96.642889] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [96.643182] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [96.646724] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [96.646737] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [96.647049] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [96.647805] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [96.648193] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [96.648491] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [96.648737] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [96.649440] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [96.819528] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [96.819661] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [96.820085] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [96.820801] [IGT] kms_pm_rpm: exiting, ret=0
<6> [96.821982] Console: switching to colour frame buffer device 128x48
Created at 2024-03-10 22:41:12