Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 1.32 seconds
Igt-Version 
IGT-Version: 1.28-g86173d01d (x86_64) (Linux: 6.8.0-linus-v6.8-ge8f897f4afef+ x86_64)
Out 
Using IGT_SRANDOM=1710105534 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff888105e534b0 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     intel_atomic_commit_tail+0xaef/0xf80 [i915]
     intel_atomic_commit+0x321/0x370 [i915]
     drm_atomic_commit+0x92/0xc0
     drm_atomic_helper_set_config+0x77/0xc0
     drm_mode_setcrtc+0x1f4/0x740
     drm_ioctl_kernel+0xa8/0x100
     drm_ioctl+0x223/0x430
     __x64_sys_ioctl+0x79/0xb0
     do_syscall_64+0x6f/0x140
     entry_SYSCALL_64_after_hwframe+0x6e/0x76
Subtest basic-rte: SUCCESS (1.316s)
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff888105e534b0 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     __gt_park+0x154/0x210 [i915]
     ____intel_wakeref_put_last+0x1d/0x80 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x76/0x80 [i915]
     i915_forcewake_release+0x1d/0x40 [i915]
     full_proxy_release+0x39/0xa0
     __fput+0xa1/0x2d0
     __x64_sys_close+0x39/0x80
     do_syscall_64+0x6f/0x140
     entry_SYSCALL_64_after_hwframe+0x6e/0x76
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (1.316s)
Dmesg
<6> [108.333509] Console: switching to colour dummy device 80x25
<6> [108.333552] [IGT] kms_pm_rpm: executing
<6> [108.336255] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [108.336352] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [108.342213] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [108.342221] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [108.342494] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [108.342820] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [108.342823] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [108.342993] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [108.343313] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [108.343317] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [108.343499] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [108.343797] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [108.343800] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [108.343945] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [108.344369] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [108.344372] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [108.344512] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [108.344523] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [108.344526] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [108.344652] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [108.344661] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [108.344663] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [108.344802] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [108.344811] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [108.344814] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [108.344948] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [108.344966] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [108.344968] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [108.345086] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [108.345126] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [108.345128] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [108.345253] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [108.345299] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [108.345304] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [108.345489] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [108.345536] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [108.345539] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [108.345696] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [108.496580] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [108.497784] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [108.498699] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [108.500155] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.346625] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [109.350932] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [109.351965] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [109.352299] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [109.352582] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [109.352824] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [109.352949] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [109.353086] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [109.379117] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [109.379818] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [109.380780] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [109.381701] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [109.382628] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [109.383431] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [109.384109] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [109.384835] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [109.385357] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [109.385965] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [109.389930] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [109.390136] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [109.393334] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [109.394313] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [109.394568] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.394728] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [109.395070] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [109.395231] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [109.395651] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [109.395617] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [109.396084] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.396224] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.396400] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [109.396721] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [109.397056] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [109.397420] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [109.397544] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [109.415614] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [109.416083] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [109.416576] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [109.417474] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.418187] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [109.419220] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [109.420340] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [109.421060] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [109.421525] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [109.421870] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [109.422096] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [109.422373] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [109.498510] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [109.511780] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [109.512355] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [109.513201] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [109.514161] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [109.515154] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [109.516162] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [109.516539] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [109.516840] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [109.516940] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [109.517115] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [109.518713] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [109.518808] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [109.522012] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [109.522666] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [109.522767] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.522921] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [109.523208] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [109.523500] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [109.523656] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [109.523807] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [109.523969] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [109.524045] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [109.524440] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [109.524558] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [109.542615] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [109.543092] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [109.543543] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [109.544244] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.544660] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [109.545543] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [109.546617] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [109.547316] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [109.547659] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [109.547961] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [109.548152] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [109.548388] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [109.638450] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [109.638995] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [109.639944] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [109.640852] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [109.641941] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [109.643065] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [109.644048] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [109.645970] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [109.646088] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [109.646310] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [109.647917] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [109.648013] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [109.651189] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [109.651839] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [109.651948] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<6> [109.652638] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [109.652668] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [109.652756] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [109.653058] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [109.653344] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [109.653492] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [109.653639] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [109.653805] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [109.653886] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [109.654049] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [109.654128] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [109.778573] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [109.779602] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [109.780462] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [109.781626] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.782574] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [109.783691] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [109.784726] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [109.784986] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [109.785206] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [109.785400] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [109.785513] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [109.785650] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [109.870954] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [109.871529] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [109.872433] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [109.873337] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [109.874237] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [109.875339] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [109.876195] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [109.877651] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [109.878120] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [109.878567] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [109.880826] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [109.880996] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [109.884760] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [109.885645] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [109.885816] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.885952] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [109.886235] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [109.886712] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [109.886847] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [109.886977] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [109.887121] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<6> [109.887312] [IGT] kms_pm_rpm: exiting, ret=0
<6> [109.888697] Console: switching to colour frame buffer device 128x48
Created at 2024-03-10 22:41:12