Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 0.02 seconds
Igt-Version 
IGT-Version: 1.28-g40ed74461 (x86_64) (Linux: 6.8.0-rc7-linus-v6.8-rc7-g90d35da658da+ x86_64)
Out 
Using IGT_SRANDOM=1709500517 for randomisation
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.024s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.024s)
Dmesg
<6> [118.297442] Console: switching to colour dummy device 80x25
<6> [118.297799] [IGT] kms_force_connector_basic: executing
<7> [118.302505] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [118.303223] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [118.319531] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [118.320243] [drm:status_store] [CONNECTOR:95:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [118.320250] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.320256] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.320645] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.320779] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.321100] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.321255] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.321261] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.321391] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [118.324238] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.324243] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [118.324388] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [118.324428] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.324433] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.324789] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.324921] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.325231] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.325382] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.325386] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.325533] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [118.328353] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.328357] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [118.328512] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [118.328642] [drm:status_store] [CONNECTOR:104:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [118.328648] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2]
<7> [118.328653] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:104:HDMI-A-2]
<7> [118.341756] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD monitor Dummy #4B
<7> [118.341762] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD size 32, SAD count 0
<7> [118.341982] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.342116] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [118.342429] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.342573] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [118.342616] i915 0000:00:02.0: [drm:do_detailed_mode] [CONNECTOR:104:HDMI-A-2] reducing hsync_end 2100->2092
<7> [118.342798] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2] probed modes :
<7> [118.342802] [drm:drm_mode_debug_printmodeline] Modeline "1920x1200": 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x48 0x9
<7> [118.342807] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 140000 1920 2068 2092 2092 1080 1082 1087 1115 0x40 0x9
<7> [118.342811] [drm:drm_mode_debug_printmodeline] Modeline "1680x1050": 60 119000 1680 1728 1760 1840 1050 1053 1059 1080 0x40 0x9
<7> [118.342815] [drm:drm_mode_debug_printmodeline] Modeline "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [118.342819] [drm:drm_mode_debug_printmodeline] Modeline "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [118.342822] [drm:drm_mode_debug_printmodeline] Modeline "1440x900": 60 88750 1440 1488 1520 1600 900 903 909 926 0x40 0x9
<7> [118.342826] [drm:drm_mode_debug_printmodeline] Modeline "1280x960": 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
<7> [118.342830] [drm:drm_mode_debug_printmodeline] Modeline "1280x800": 60 71000 1280 1328 1360 1440 800 803 809 823 0x40 0x9
<7> [118.342834] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.342837] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.342841] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.342845] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.342874] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2]
<7> [118.342878] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:104:HDMI-A-2]
<7> [118.356058] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD monitor Dummy #4B
<7> [118.356064] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD size 32, SAD count 0
<7> [118.356279] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.356424] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [118.356732] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.356875] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [118.356912] i915 0000:00:02.0: [drm:do_detailed_mode] [CONNECTOR:104:HDMI-A-2] reducing hsync_end 2100->2092
<7> [118.357088] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2] probed modes :
<7> [118.357091] [drm:drm_mode_debug_printmodeline] Modeline "1920x1200": 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x48 0x9
<7> [118.357096] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 140000 1920 2068 2092 2092 1080 1082 1087 1115 0x40 0x9
<7> [118.357099] [drm:drm_mode_debug_printmodeline] Modeline "1680x1050": 60 119000 1680 1728 1760 1840 1050 1053 1059 1080 0x40 0x9
<7> [118.357103] [drm:drm_mode_debug_printmodeline] Modeline "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [118.357106] [drm:drm_mode_debug_printmodeline] Modeline "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [118.357110] [drm:drm_mode_debug_printmodeline] Modeline "1440x900": 60 88750 1440 1488 1520 1600 900 903 909 926 0x40 0x9
<7> [118.357113] [drm:drm_mode_debug_printmodeline] Modeline "1280x960": 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
<7> [118.357116] [drm:drm_mode_debug_printmodeline] Modeline "1280x800": 60 71000 1280 1328 1360 1440 800 803 809 823 0x40 0x9
<7> [118.357120] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.357123] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.357126] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.357130] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.357273] [drm:status_store] [CONNECTOR:115:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [118.357278] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3]
<7> [118.357282] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:115:HDMI-A-3]
<7> [118.357638] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.357760] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [118.358067] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.358210] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.358215] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.358333] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [118.361163] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.361167] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [118.361301] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3] disconnected
<7> [118.361331] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3]
<7> [118.361335] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:115:HDMI-A-3]
<7> [118.361686] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.361806] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [118.362105] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.362245] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.362249] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.362367] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [118.365182] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.365187] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [118.365319] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3] disconnected
<7> [118.365358] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.365362] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.365713] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.365833] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.366132] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.366272] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.366276] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.366394] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [118.369210] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.369214] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [118.369343] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<6> [118.369691] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [118.369811] [drm:status_store] [CONNECTOR:95:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [118.369816] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.369820] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.370160] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.370281] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.370592] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.370734] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.370741] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.370860] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [118.373695] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.373703] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [118.373829] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] status updated from disconnected to connected
<7> [118.373981] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] probed modes :
<7> [118.373987] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.373994] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.374001] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.374007] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [118.374013] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.374056] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.374062] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.374452] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.374575] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.374882] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.375023] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.375032] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.375149] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [118.377987] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.377995] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [118.378194] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] probed modes :
<7> [118.378198] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.378203] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.378206] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.378210] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [118.378213] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.378354] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:95:HDMI-A-1] EDID override set
<7> [118.378371] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.378375] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.378539] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:HDMI-A-1] ELD monitor IGT
<7> [118.378544] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:HDMI-A-1] ELD size 24, SAD count 0
<7> [118.378758] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
<7> [118.378881] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.379181] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
<7> [118.379323] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [118.379445] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.379451] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [118.379457] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [118.379461] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [118.379467] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] probed modes :
<7> [118.379470] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [118.379474] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [118.379477] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [118.379481] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.379484] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.379487] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.379597] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:95:HDMI-A-1] EDID override set
<7> [118.379622] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.379626] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.379776] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:HDMI-A-1] ELD monitor IGT
<7> [118.379780] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:HDMI-A-1] ELD size 24, SAD count 0
<7> [118.379784] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:95:HDMI-A-1] EDID changed, epoch counter 4
<7> [118.380001] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
<7> [118.380122] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.380433] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
<7> [118.380576] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [118.380673] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [118.380678] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [118.380684] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] probed modes :
<7> [118.380687] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [118.380690] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [118.380694] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.380697] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.380701] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.380794] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:95:HDMI-A-1] EDID override reset
<7> [118.380815] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.380819] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.381159] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.381279] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.381592] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.381734] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.381741] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.381859] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [118.384690] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.384697] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [118.384820] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:95:HDMI-A-1] EDID changed, epoch counter 5
<7> [118.384893] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [118.384898] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [118.384903] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [118.384907] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [118.384913] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] probed modes :
<7> [118.384916] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.384919] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.384923] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.384926] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [118.384929] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.385049] [drm:status_store] [CONNECTOR:95:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [118.385054] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.385059] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.385400] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.385535] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.385836] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.385979] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.385984] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.386102] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [118.388932] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.388936] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [118.389069] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] status updated from connected to disconnected
<7> [118.389080] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [118.389131] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.389135] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.389524] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.389705] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.390072] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.390278] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.390285] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.390476] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [118.393417] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.393432] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [118.393572] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<6> [118.393937] [IGT] kms_force_connector_basic: finished subtest prune-stale-modes, SUCCESS
<7> [118.394048] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [118.394661] [drm:status_store] [CONNECTOR:95:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [118.394667] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.394672] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.395035] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.395157] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.395471] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.395614] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.395618] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.395737] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [118.398568] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.398573] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [118.398708] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [118.398740] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.398745] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.399097] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.399217] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.399521] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.399664] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.399668] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.399787] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [118.402618] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.402623] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [118.402755] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [118.402846] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:95:HDMI-A-1] EDID override reset
<7> [118.402863] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.402867] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.403219] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.403339] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.403682] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.403825] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.403829] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.403948] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [118.406781] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.406786] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [118.406918] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [118.407053] [drm:status_store] [CONNECTOR:104:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [118.407058] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2]
<7> [118.407063] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:104:HDMI-A-2]
<7> [118.420281] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD monitor Dummy #4B
<7> [118.420288] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD size 32, SAD count 0
<7> [118.420510] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.420637] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [118.420955] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.421100] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [118.421139] i915 0000:00:02.0: [drm:do_detailed_mode] [CONNECTOR:104:HDMI-A-2] reducing hsync_end 2100->2092
<7> [118.421321] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2] probed modes :
<7> [118.421325] [drm:drm_mode_debug_printmodeline] Modeline "1920x1200": 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x48 0x9
<7> [118.421330] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 140000 1920 2068 2092 2092 1080 1082 1087 1115 0x40 0x9
<7> [118.421334] [drm:drm_mode_debug_printmodeline] Modeline "1680x1050": 60 119000 1680 1728 1760 1840 1050 1053 1059 1080 0x40 0x9
<7> [118.421337] [drm:drm_mode_debug_printmodeline] Modeline "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [118.421341] [drm:drm_mode_debug_printmodeline] Modeline "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [118.421345] [drm:drm_mode_debug_printmodeline] Modeline "1440x900": 60 88750 1440 1488 1520 1600 900 903 909 926 0x40 0x9
<7> [118.421349] [drm:drm_mode_debug_printmodeline] Modeline "1280x960": 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
<7> [118.421352] [drm:drm_mode_debug_printmodeline] Modeline "1280x800": 60 71000 1280 1328 1360 1440 800 803 809 823 0x40 0x9
<7> [118.421356] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.421360] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.421363] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.421367] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.421400] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2]
<7> [118.421404] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:104:HDMI-A-2]
<7> [118.434516] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD monitor Dummy #4B
<7> [118.434522] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD size 32, SAD count 0
<7> [118.434754] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.434879] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [118.435194] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.435336] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [118.435372] i915 0000:00:02.0: [drm:do_detailed_mode] [CONNECTOR:104:HDMI-A-2] reducing hsync_end 2100->2092
<7> [118.435577] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2] probed modes :
<7> [118.435582] [drm:drm_mode_debug_printmodeline] Modeline "1920x1200": 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x48 0x9
<7> [118.435587] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 140000 1920 2068 2092 2092 1080 1082 1087 1115 0x40 0x9
<7> [118.435591] [drm:drm_mode_debug_printmodeline] Modeline "1680x1050": 60 119000 1680 1728 1760 1840 1050 1053 1059 1080 0x40 0x9
<7> [118.435595] [drm:drm_mode_debug_printmodeline] Modeline "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [118.435598] [drm:drm_mode_debug_printmodeline] Modeline "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [118.435602] [drm:drm_mode_debug_printmodeline] Modeline "1440x900": 60 88750 1440 1488 1520 1600 900 903 909 926 0x40 0x9
<7> [118.435606] [drm:drm_mode_debug_printmodeline] Modeline "1280x960": 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
<7> [118.435609] [drm:drm_mode_debug_printmodeline] Modeline "1280x800": 60 71000 1280 1328 1360 1440 800 803 809 823 0x40 0x9
<7> [118.435613] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.435616] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.435620] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.435623] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.435718] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:104:HDMI-A-2] EDID override reset
<7> [118.435735] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2]
<7> [118.435739] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:104:HDMI-A-2]
<7> [118.449233] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD monitor Dummy #4B
<7> [118.449240] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD size 32, SAD count 0
<7> [118.449468] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.449602] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [118.449919] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.450062] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [118.450099] i915 0000:00:02.0: [drm:do_detailed_mode] [CONNECTOR:104:HDMI-A-2] reducing hsync_end 2100->2092
<7> [118.450271] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2] probed modes :
<7> [118.450274] [drm:drm_mode_debug_printmodeline] Modeline "1920x1200": 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x48 0x9
<7> [118.450279] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 140000 1920 2068 2092 2092 1080 1082 1087 1115 0x40 0x9
<7> [118.450282] [drm:drm_mode_debug_printmodeline] Modeline "1680x1050": 60 119000 1680 1728 1760 1840 1050 1053 1059 1080 0x40 0x9
<7> [118.450286] [drm:drm_mode_debug_printmodeline] Modeline "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [118.450289] [drm:drm_mode_debug_printmodeline] Modeline "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [118.450293] [drm:drm_mode_debug_printmodeline] Modeline "1440x900": 60 88750 1440 1488 1520 1600 900 903 909 926 0x40 0x9
<7> [118.450296] [drm:drm_mode_debug_printmodeline] Modeline "1280x960": 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
<7> [118.450299] [drm:drm_mode_debug_printmodeline] Modeline "1280x800": 60 71000 1280 1328 1360 1440 800 803 809 823 0x40 0x9
<7> [118.450303] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.450306] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.450309] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.450313] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.450436] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:108:DP-1] EDID override reset
<7> [118.450463] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-1]
<7> [118.450471] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-1]
<7> [118.450638] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-1] disconnected
<7> [118.450757] [drm:status_store] [CONNECTOR:115:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [118.450762] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3]
<7> [118.450767] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:115:HDMI-A-3]
<7> [118.451125] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.451246] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [118.451585] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.451730] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.451735] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.451853] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [118.454693] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.454699] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [118.454831] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3] disconnected
<7> [118.454863] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3]
<7> [118.454868] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:115:HDMI-A-3]
<7> [118.455227] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.455347] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [118.455685] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.455827] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.455831] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.455950] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [118.458773] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.458777] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [118.458911] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3] disconnected
<7> [118.458997] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:115:HDMI-A-3] EDID override reset
<7> [118.459014] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3]
<7> [118.459018] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:115:HDMI-A-3]
<7> [118.459370] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.459508] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [118.459835] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.459976] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.459980] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.460098] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [118.462925] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.462930] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [118.463070] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3] disconnected
<7> [118.463167] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:119:DP-2] EDID override reset
<7> [118.463184] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-2]
<7> [118.463188] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-2]
<7> [118.463994] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI E/PHY E: DPCD: 11 0a 82 01 00 03 01 01 02 00 00 00 00 00 00
<7> [118.464632] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI E/PHY E: DP branch: OUI 00-00-00 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000
<7> [118.465564] i915 0000:00:02.0: [drm:drm_dp_read_downstream_info [drm_display_helper]] AUX A/DDI E/PHY E: DPCD DFP: 09
<7> [118.465576] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:118:DDI E/PHY E] MST support: port: no, sink: no, modparam: yes
<7> [118.465708] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [118.465831] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [118.465952] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<5> [118.471690] EDID block 0 is all zeroes
<7> [118.471694] i915 0000:00:02.0: [drm:connector_bad_edid] [CONNECTOR:119:DP-2] EDID is invalid:
<7> [118.471700] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.471703] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.471705] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.471707] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.471710] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.471712] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.471714] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.471715] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.471722] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] VRR capable: no
<7> [118.471849] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] DFP max bpc 8, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [118.472604] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.472730] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [118.473393] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-2] probed modes :
<7> [118.473397] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x48 0xa
<7> [118.473402] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.473406] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.473432] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.473437] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<6> [118.474024] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [118.474128] [drm:status_store] [CONNECTOR:95:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [118.474134] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.474139] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.474502] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.474626] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.474944] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.475086] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.475091] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.475209] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [118.478051] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.478056] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [118.478189] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [118.478232] [drm:status_store] [CONNECTOR:104:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [118.478237] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2]
<7> [118.478242] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:104:HDMI-A-2]
<7> [118.491473] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD monitor Dummy #4B
<7> [118.491480] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD size 32, SAD count 0
<7> [118.491716] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.491843] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [118.492161] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.492304] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [118.492344] i915 0000:00:02.0: [drm:do_detailed_mode] [CONNECTOR:104:HDMI-A-2] reducing hsync_end 2100->2092
<7> [118.492553] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2] probed modes :
<7> [118.492558] [drm:drm_mode_debug_printmodeline] Modeline "1920x1200": 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x48 0x9
<7> [118.492563] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 140000 1920 2068 2092 2092 1080 1082 1087 1115 0x40 0x9
<7> [118.492567] [drm:drm_mode_debug_printmodeline] Modeline "1680x1050": 60 119000 1680 1728 1760 1840 1050 1053 1059 1080 0x40 0x9
<7> [118.492571] [drm:drm_mode_debug_printmodeline] Modeline "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [118.492575] [drm:drm_mode_debug_printmodeline] Modeline "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [118.492579] [drm:drm_mode_debug_printmodeline] Modeline "1440x900": 60 88750 1440 1488 1520 1600 900 903 909 926 0x40 0x9
<7> [118.492583] [drm:drm_mode_debug_printmodeline] Modeline "1280x960": 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
<7> [118.492587] [drm:drm_mode_debug_printmodeline] Modeline "1280x800": 60 71000 1280 1328 1360 1440 800 803 809 823 0x40 0x9
<7> [118.492591] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.492594] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.492598] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.492602] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.492647] [drm:status_store] [CONNECTOR:115:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [118.492651] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3]
<7> [118.492656] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:115:HDMI-A-3]
<7> [118.493015] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.493137] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [118.493499] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.493652] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.493656] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.493775] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [118.496616] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.496621] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [118.496754] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3] disconnected
<7> [118.496935] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [118.509801] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [118.509806] [drm:drm_client_modeset_probe]
<7> [118.509840] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [118.509846] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [118.510256] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.510400] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [118.510729] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [118.510876] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.510880] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.510999] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [118.513845] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [118.513850] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [118.513987] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [118.513993] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2]
<7> [118.513998] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:104:HDMI-A-2]
<7> [118.527250] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD monitor Dummy #4B
<7> [118.527257] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:104:HDMI-A-2] ELD size 32, SAD count 0
<7> [118.527484] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.527624] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [118.527926] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0040 w(1)
<7> [118.528070] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [118.528113] i915 0000:00:02.0: [drm:do_detailed_mode] [CONNECTOR:104:HDMI-A-2] reducing hsync_end 2100->2092
<7> [118.528300] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:104:HDMI-A-2] probed modes :
<7> [118.528304] [drm:drm_mode_debug_printmodeline] Modeline "1920x1200": 60 154000 1920 1968 2000 2080 1200 1203 1209 1235 0x48 0x9
<7> [118.528309] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 140000 1920 2068 2092 2092 1080 1082 1087 1115 0x40 0x9
<7> [118.528313] [drm:drm_mode_debug_printmodeline] Modeline "1680x1050": 60 119000 1680 1728 1760 1840 1050 1053 1059 1080 0x40 0x9
<7> [118.528317] [drm:drm_mode_debug_printmodeline] Modeline "1600x900": 60 108000 1600 1624 1704 1800 900 901 904 1000 0x40 0x5
<7> [118.528321] [drm:drm_mode_debug_printmodeline] Modeline "1280x1024": 60 108000 1280 1328 1440 1688 1024 1025 1028 1066 0x40 0x5
<7> [118.528324] [drm:drm_mode_debug_printmodeline] Modeline "1440x900": 60 88750 1440 1488 1520 1600 900 903 909 926 0x40 0x9
<7> [118.528328] [drm:drm_mode_debug_printmodeline] Modeline "1280x960": 60 108000 1280 1376 1488 1800 960 961 964 1000 0x40 0x5
<7> [118.528332] [drm:drm_mode_debug_printmodeline] Modeline "1280x800": 60 71000 1280 1328 1360 1440 800 803 809 823 0x40 0x9
<7> [118.528336] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.528339] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.528343] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.528347] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.528351] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-1]
<7> [118.528356] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-1]
<7> [118.528522] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-1] disconnected
<7> [118.528527] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3]
<7> [118.528531] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:115:HDMI-A-3]
<7> [118.528868] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.528989] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [118.529289] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [118.529443] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.529447] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.529564] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [118.532397] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [118.532402] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [118.532546] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:115:HDMI-A-3] disconnected
<7> [118.532551] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-2]
<7> [118.532556] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-2]
<7> [118.533363] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI E/PHY E: DPCD: 11 0a 82 01 00 03 01 01 02 00 00 00 00 00 00
<7> [118.534038] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI E/PHY E: DP branch: OUI 00-00-00 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000
<7> [118.534999] i915 0000:00:02.0: [drm:drm_dp_read_downstream_info [drm_display_helper]] AUX A/DDI E/PHY E: DPCD DFP: 09
<7> [118.535011] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:118:DDI E/PHY E] MST support: port: no, sink: no, modparam: yes
<7> [118.535146] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [118.535269] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [118.535390] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<5> [118.541461] EDID block 0 is all zeroes
<7> [118.541465] i915 0000:00:02.0: [drm:connector_bad_edid] [CONNECTOR:119:DP-2] EDID is invalid:
<7> [118.541470] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.541473] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.541475] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.541477] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.541479] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.541481] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.541483] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.541485] [00] ZERO 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.541491] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] VRR capable: no
<7> [118.541618] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] DFP max bpc 8, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [118.542388] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [118.542528] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:119:DP-2] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [118.543215] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:119:DP-2] probed modes :
<7> [118.543220] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x48 0xa
<7> [118.543225] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.543229] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.543233] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.543237] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [118.543241] [drm:drm_client_modeset_probe] connector 95 enabled? no
<7> [118.543244] [drm:drm_client_modeset_probe] connector 104 enabled? yes
<7> [118.543247] [drm:drm_client_modeset_probe] connector 108 enabled? no
<7> [118.543249] [drm:drm_client_modeset_probe] connector 115 enabled? no
<7> [118.543252] [drm:drm_client_modeset_probe] connector 119 enabled? yes
<7> [118.543273] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [118.543281] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 104
<7> [118.543284] [drm:drm_client_modeset_probe] looking for preferred mode on connector 104 0
<7> [118.543287] [drm:drm_client_modeset_probe] found mode 1920x1200
<7> [118.543289] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 119
<7> [118.543291] [drm:drm_client_modeset_probe] looking for preferred mode on connector 119 0
<7> [118.543294] [drm:drm_client_modeset_probe] found mode 640x480
<7> [118.543296] [drm:drm_client_modeset_probe] picking CRTCs for 1920x1200 config
<7> [118.543333] [drm:drm_client_modeset_probe] desired mode 1920x1200 set on crtc 51 (0,0)
<7> [118.543339] [drm:drm_client_modeset_probe] desired mode 640x480 set on crtc 72 (0,0)
<6> [118.576728] Console: switching to colour frame buffer device 80x30
Created at 2024-03-03 22:45:28