Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 11.56 seconds
Igt-Version 
IGT-Version: 1.28-g40ed74461 (x86_64) (Linux: 6.8.0-rc7-linus-v6.8-rc7-g90d35da658da+ x86_64)
Out 
Using IGT_SRANDOM=1709500501 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff88811244b4b0 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     intel_dp_aux_xfer+0x4c9/0x6d0 [i915]
     intel_dp_aux_transfer+0x1dc/0x2a0 [i915]
     drm_dp_dpcd_access+0x6d/0x130 [drm_display_helper]
     drm_dp_dpcd_read+0xeb/0x100 [drm_display_helper]
     drm_dp_read_sink_count+0x2c/0x80 [drm_display_helper]
     intel_dp_get_dpcd+0x9c/0xc0 [i915]
     intel_dp_detect+0xe4/0x680 [i915]
     drm_helper_probe_detect_ctx+0x45/0x100
     intel_hotplug_detect_connector+0x3e/0x100 [i915]
     i915_hpd_poll_init_work+0x178/0x220 [i915]
     process_scheduled_works+0x2de/0x530
     worker_thread+0x18c/0x350
     kthread+0x100/0x130
     ret_from_fork+0x2f/0x50
Subtest basic-rte: SUCCESS (11.565s)
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff88811244b4b0 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     __gt_park+0x154/0x210 [i915]
     ____intel_wakeref_put_last+0x20/0x80 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x76/0x80 [i915]
     i915_forcewake_release+0x1d/0x40 [i915]
     full_proxy_release+0x3c/0xa0
     __fput+0xa4/0x2d0
     __x64_sys_close+0x39/0x80
     do_syscall_64+0x72/0x140
     entry_SYSCALL_64_after_hwframe+0x6e/0x76
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (11.565s)
Dmesg
<6> [91.662028] Console: switching to colour dummy device 80x25
<6> [91.662080] [IGT] kms_pm_rpm: executing
<6> [91.671049] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [91.671096] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [91.675166] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [91.675173] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [91.675357] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [91.675765] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [91.675779] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [91.676828] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.677824] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.678479] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [91.678958] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [91.678963] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [91.679551] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.679669] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.680076] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.680269] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.680273] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.680386] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.684618] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.684623] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.684747] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [91.685103] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [91.685108] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [91.685268] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [91.685284] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [91.685287] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [91.686457] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.687556] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.688400] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [91.688418] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [91.688422] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [91.688912] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.689040] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.689413] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.689566] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.689570] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.689682] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.693834] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.693838] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.693961] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [91.693988] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [91.693992] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [91.694177] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [91.694230] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [91.694234] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [91.695405] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.696552] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.697405] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [91.697468] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [91.697472] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [91.697912] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.698027] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.698410] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.698563] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.698567] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.698679] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.702890] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.702894] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.703016] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [91.804929] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [91.805235] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.805485] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.805728] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.806453] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [102.156987] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [102.162693] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [102.756978] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [102.762334] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [102.762954] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [102.763759] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [102.763742] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [102.764509] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [102.765285] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [102.765923] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [102.766573] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [102.768274] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [102.769443] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [102.770295] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [102.770731] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [102.770858] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [102.771296] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [102.771452] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [102.771456] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [102.771569] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [102.775734] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [102.775739] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [102.776030] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [102.776122] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [102.876964] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [102.894978] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [102.895454] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [102.895933] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [102.896888] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [102.897447] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [102.904401] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [102.977228] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [102.989656] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [102.998956] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [102.999938] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.000443] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.001159] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.002074] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [103.002512] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [103.002740] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [103.002994] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [103.004530] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.005567] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.006227] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [103.006795] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.007002] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.007486] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.007736] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.007744] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.007962] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.012328] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.012333] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.012698] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [103.124932] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [103.125249] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.125507] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.125750] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.126491] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.126791] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [103.130813] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [103.225746] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [103.233930] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [103.234274] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.234404] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.234860] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [103.235821] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [103.235846] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [103.236029] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [103.236192] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [103.236357] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [103.236572] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [103.237605] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.238827] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.239674] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [103.240172] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.240302] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.240675] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.240874] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.240880] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.241006] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.245245] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.245251] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.245537] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [103.445011] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [103.445659] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.446270] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.446868] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.447912] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.448529] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [103.453640] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [103.559040] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [103.569700] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [103.570262] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.570647] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.571603] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.573340] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<6> [103.573998] [IGT] kms_pm_rpm: exiting, ret=0
<7> [103.573834] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [103.574436] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [103.576559] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.577708] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.578466] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [103.578973] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.579184] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.579660] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.579938] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.579945] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.580148] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.584595] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.584599] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<6> [103.585045] Console: switching to colour frame buffer device 128x48
Created at 2024-03-03 22:45:28