Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 1.32 seconds
Igt-Version 
IGT-Version: 1.28-g40ed74461 (x86_64) (Linux: 6.8.0-rc7-linus-v6.8-rc7-g90d35da658da+ x86_64)
Out 
Using IGT_SRANDOM=1709500524 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff8881186eb4b0 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     intel_atomic_commit_tail+0xaef/0xf80 [i915]
     intel_atomic_commit+0x321/0x370 [i915]
     drm_atomic_commit+0x92/0xc0
     drm_atomic_helper_set_config+0x77/0xc0
     drm_mode_setcrtc+0x1f4/0x740
     drm_ioctl_kernel+0xa8/0x100
     drm_ioctl+0x223/0x430
     __x64_sys_ioctl+0x79/0xb0
     do_syscall_64+0x6f/0x140
     entry_SYSCALL_64_after_hwframe+0x6e/0x76
Subtest basic-rte: SUCCESS (1.318s)
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff8881186eb4b0 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     __gt_park+0x154/0x210 [i915]
     ____intel_wakeref_put_last+0x1d/0x80 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x76/0x80 [i915]
     i915_forcewake_release+0x1d/0x40 [i915]
     full_proxy_release+0x39/0xa0
     __fput+0xa1/0x2d0
     __x64_sys_close+0x39/0x80
     do_syscall_64+0x6f/0x140
     entry_SYSCALL_64_after_hwframe+0x6e/0x76
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (1.318s)
Dmesg
<6> [113.342457] Console: switching to colour dummy device 80x25
<6> [113.342513] [IGT] kms_pm_rpm: executing
<6> [113.345288] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [113.345362] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [113.353152] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [113.353167] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [113.353399] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [113.353832] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [113.353838] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [113.354028] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [113.354470] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [113.354476] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [113.354688] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [113.355121] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [113.355126] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [113.355327] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [113.355870] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [113.355875] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [113.356057] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [113.356074] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [113.356078] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [113.356255] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [113.356270] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [113.356274] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [113.356466] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [113.356480] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [113.356483] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [113.356672] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [113.356698] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [113.356702] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [113.356863] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [113.356918] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [113.356922] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [113.357103] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [113.357162] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [113.357165] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [113.357357] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [113.357412] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [113.357416] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [113.357602] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [113.511420] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.512439] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.513308] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.514471] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.358601] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [114.360958] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [114.362948] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [114.364630] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [114.365683] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [114.365870] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [114.365968] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [114.366114] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [114.392355] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [114.392857] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [114.393855] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [114.394823] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [114.395770] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [114.396722] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [114.397622] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [114.398440] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [114.399024] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [114.399836] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [114.404557] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.404772] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [114.407973] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [114.408966] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [114.409525] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [114.409623] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.409726] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [114.410003] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [114.410277] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [114.410407] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [114.410535] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [114.410678] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [114.410826] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [114.410911] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [114.410975] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [114.428386] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [114.428875] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.429382] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [114.430175] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.430727] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [114.431416] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [114.432682] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [114.433787] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [114.434296] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [114.434517] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [114.434648] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [114.434809] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [114.511730] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [114.525010] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [114.525704] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [114.526613] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [114.527535] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [114.528501] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [114.529484] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [114.530179] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [114.530559] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [114.530662] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [114.530857] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [114.532448] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.532541] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [114.535741] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [114.536398] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [114.536688] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.536869] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [114.537173] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [114.537415] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [114.537564] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [114.537700] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [114.537847] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [114.537997] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [114.538087] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [114.538153] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [114.556396] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [114.556981] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.557543] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [114.558372] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.558976] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [114.559716] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [114.561032] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [114.561821] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [114.562090] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [114.562312] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [114.562444] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [114.562606] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [114.651756] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [114.652407] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [114.653324] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [114.654215] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [114.655131] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [114.656004] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [114.656849] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [114.656998] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [114.657107] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [114.657283] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [114.658851] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.658945] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [114.661682] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [114.662221] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [114.662330] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<6> [114.662934] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [114.662955] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [114.663030] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [114.663381] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [114.663667] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [114.663822] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [114.663968] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [114.664089] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [114.664156] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [114.664408] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [114.664477] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [114.785410] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [114.786399] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.787276] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [114.788454] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.789386] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [114.790604] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [114.791648] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [114.791964] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [114.792246] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [114.792466] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [114.792597] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [114.792759] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [114.881784] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [114.882474] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [114.883409] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [114.884328] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [114.885294] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [114.886270] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [114.887211] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [114.888931] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [114.889453] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [114.889773] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [114.891383] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.891483] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [114.895204] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [114.896062] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [114.896221] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.896342] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [114.896619] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [114.896982] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [114.897132] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<6> [114.897227] [IGT] kms_pm_rpm: exiting, ret=0
<7> [114.897261] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [114.897400] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<6> [114.898788] Console: switching to colour frame buffer device 128x48
Created at 2024-03-03 22:45:27