Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 0.38 seconds
Igt-Version 
IGT-Version: 1.28-gca4607939 (x86_64) (Linux: 6.8.0-rc6-linus-v6.8-rc6-gd206a76d7d27+ x86_64)
Out 
Using IGT_SRANDOM=1708905326 for randomisation
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.383s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.383s)
Dmesg
<6> [115.761781] Console: switching to colour dummy device 80x25
<6> [115.761817] [IGT] kms_force_connector_basic: executing
<7> [115.764081] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [115.764704] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [115.777319] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [115.778202] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [115.778213] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [115.778222] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.778563] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [115.778623] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [115.778632] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.778945] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [115.779014] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [115.779020] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.779328] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<6> [115.779389] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [115.779501] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [115.779506] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [115.779510] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.832191] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [115.841183] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [115.841193] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [115.841299] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [115.848364] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [115.848370] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [115.848470] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] status updated from disconnected to connected
<7> [115.848579] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [115.848582] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [115.848588] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [115.848592] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [115.848595] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [115.848598] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [115.848634] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [115.848637] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.899838] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [115.908198] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.908432] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.908550] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.909678] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [115.909688] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [115.909826] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [115.926885] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [115.926898] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [115.927026] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.927252] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [115.927257] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [115.927264] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [115.927268] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [115.927272] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [115.927275] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [115.927488] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:249:HDMI-A-1] EDID override set
<7> [115.927510] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [115.927515] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.927654] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.927827] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD monitor IGT
<7> [115.927832] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD size 24, SAD count 0
<7> [115.979588] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [116.000032] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [116.000049] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [116.000298] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [116.000304] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [116.000311] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [116.000315] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [116.000321] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [116.000325] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [116.000329] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [116.000333] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [116.000336] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [116.000340] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [116.000344] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [116.000473] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:249:HDMI-A-1] EDID override set
<7> [116.000497] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [116.000501] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [116.000642] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [116.000832] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD monitor IGT
<7> [116.000837] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD size 24, SAD count 0
<7> [116.000841] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:249:HDMI-A-1] EDID changed, epoch counter 4
<7> [116.053750] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [116.072722] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [116.072735] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [116.072893] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [116.072898] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [116.072904] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [116.072906] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [116.072909] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [116.072912] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [116.072915] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [116.072917] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [116.072997] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:249:HDMI-A-1] EDID override reset
<7> [116.073014] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [116.073016] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [116.073144] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [116.124967] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [116.144511] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [116.144517] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [116.144606] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [116.161577] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [116.161581] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [116.161667] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:249:HDMI-A-1] EDID changed, epoch counter 5
<7> [116.161674] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [116.161801] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [116.161805] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [116.161808] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [116.161811] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [116.161814] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [116.161816] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [116.161819] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [116.161821] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [116.161823] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [116.161825] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [116.161918] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [116.161921] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [116.161924] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [116.162021] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [116.162348] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] status updated from connected to disconnected
<7> [116.162357] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [116.162431] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [116.162434] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [116.162870] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<6> [116.162936] [IGT] kms_force_connector_basic: finished subtest prune-stale-modes, SUCCESS
<7> [116.163041] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [116.163619] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:236:DP-1] EDID override reset
<7> [116.163631] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [116.163635] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [116.163953] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [116.164037] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [116.164040] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [116.164043] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [116.164473] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [116.164493] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [116.164496] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [116.164640] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [116.164694] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:249:HDMI-A-1] EDID override reset
<7> [116.164704] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [116.164707] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [116.165021] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [116.165090] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:255:DP-2] EDID override reset
<7> [116.165101] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [116.165104] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [116.165552] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [116.165617] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:264:DP-3] EDID override reset
<7> [116.165634] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [116.165638] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [116.166082] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<6> [116.166272] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [116.166338] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [116.166342] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [116.166345] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [116.166666] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [116.166794] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [116.186424] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [116.186794] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [116.187014] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [116.187022] [drm:drm_client_modeset_probe]
<7> [116.187266] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [116.187287] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [116.187533] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [116.187537] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [116.187541] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [116.187694] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [116.187697] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [116.187700] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [116.187932] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [116.187936] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [116.187938] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [116.188125] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [116.188129] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [116.188136] [drm:drm_client_modeset_probe] connector 236 enabled? no
<7> [116.188139] [drm:drm_client_modeset_probe] connector 249 enabled? no
<7> [116.188142] [drm:drm_client_modeset_probe] connector 255 enabled? no
<7> [116.188144] [drm:drm_client_modeset_probe] connector 264 enabled? no
<7> [116.188227] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [116.188241] [drm:drm_client_modeset_probe] picking CRTCs for 1024x768 config
<6> [116.189470] Console: switching to colour frame buffer device 128x48
Created at 2024-02-26 01:27:12