Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 0.03 seconds
Igt-Version 
IGT-Version: 1.28-g21e9f1e49 (x86_64) (Linux: 6.8.0-rc5-linus-v6.8-rc5-gb401b621758e+ x86_64)
Out 
Using IGT_SRANDOM=1708290526 for randomisation
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.031s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.031s)
Dmesg
<6> [170.221946] Console: switching to colour dummy device 80x25
<6> [170.222370] [IGT] kms_force_connector_basic: executing
<7> [170.226212] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [170.227796] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [170.233785] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [170.235190] [drm:status_store] [CONNECTOR:112:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [170.235200] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.235210] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.235778] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.235969] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.236349] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.236594] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.236606] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.236784] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [170.239917] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.239926] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [170.240122] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [170.240179] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.240186] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.240744] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.240922] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.241279] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.241511] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.241521] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.241761] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [170.244871] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.244879] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [170.245075] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [170.245345] [drm:status_store] [CONNECTOR:124:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [170.245354] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [170.245361] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [170.245894] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.246068] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [170.246444] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.246683] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.246693] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.246934] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [170.250178] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.250187] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [170.250389] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [170.250451] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [170.250459] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [170.250930] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.251101] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [170.251457] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.251716] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.251724] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.251947] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [170.255023] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.255032] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [170.255228] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [170.255271] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.255278] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.255756] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.255936] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.256314] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.256595] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.256604] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.256817] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [170.259917] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.259925] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [170.260120] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<6> [170.260598] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [170.260941] [drm:status_store] [CONNECTOR:112:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [170.260952] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.260964] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.261554] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.261802] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.262248] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.262463] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.262509] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.262751] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [170.266003] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.266018] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [170.266208] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] status updated from disconnected to connected
<7> [170.266320] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] probed modes :
<7> [170.266326] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [170.266335] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [170.266342] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [170.266348] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [170.266354] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [170.266419] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.266426] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.266990] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.267239] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.267702] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.267981] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.267999] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.268218] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [170.271553] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.271572] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [170.272022] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] probed modes :
<7> [170.272031] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [170.272042] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [170.272051] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [170.272060] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [170.272069] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [170.272500] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:112:HDMI-A-1] EDID override set
<7> [170.272546] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.272556] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.273119] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:112:HDMI-A-1] ELD monitor IGT
<7> [170.273130] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:112:HDMI-A-1] ELD size 24, SAD count 0
<7> [170.273559] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
<7> [170.273814] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.274268] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0040 w(1)
<7> [170.274575] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [170.274819] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [170.274832] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [170.274847] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [170.274857] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [170.274871] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] probed modes :
<7> [170.274878] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [170.274888] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [170.274896] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [170.274905] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [170.274914] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [170.275192] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:112:HDMI-A-1] EDID override reset
<7> [170.275335] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.275345] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.275919] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.276159] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.276634] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.276920] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.276937] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.277112] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [170.280292] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.280306] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [170.280511] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:112:HDMI-A-1] EDID changed, epoch counter 2
<7> [170.280683] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [170.280693] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [170.280703] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [170.280710] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [170.280720] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] probed modes :
<7> [170.280725] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [170.280731] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [170.280737] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [170.280743] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [170.280748] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [170.280975] [drm:status_store] [CONNECTOR:112:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [170.280983] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.280990] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.281430] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.281675] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.282123] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.282316] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.282323] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.282586] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [170.285826] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.285835] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [170.286020] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] status updated from connected to disconnected
<7> [170.286038] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [170.286249] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.286259] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.286810] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.287059] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.287550] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.287755] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.287762] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.287921] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [170.290961] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.290972] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [170.291247] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<6> [170.291941] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [170.292138] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [170.293443] [drm:status_store] [CONNECTOR:95:eDP-1] force updated from 0 to 0 or reprobing
<7> [170.293453] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [170.293462] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [170.294543] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [170.294756] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [170.294919] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [170.295081] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [170.295272] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [170.295281] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [170.295287] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [170.295315] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [170.295502] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [170.296725] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [170.296943] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [170.298093] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [170.298104] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [170.298115] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [170.298199] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [170.298207] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [170.299129] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [170.299364] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [170.299693] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [170.299937] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [170.300207] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [170.300218] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [170.300226] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [170.300268] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [170.300526] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [170.301706] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [170.301955] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [170.302999] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [170.303009] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [170.303019] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [170.303248] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:95:eDP-1] EDID override reset
<7> [170.303293] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [170.303303] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [170.304239] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [170.304398] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [170.304576] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [170.304790] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [170.305055] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [170.305065] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [170.305073] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [170.305107] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [170.305333] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [170.306412] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [170.306666] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [170.307683] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [170.307691] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [170.307698] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [170.307886] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:103:DP-1] EDID override reset
<7> [170.307918] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [170.307925] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [170.308146] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [170.308427] [drm:status_store] [CONNECTOR:112:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [170.308438] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.308448] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.309017] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.309230] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.309595] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.309791] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.309798] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.309949] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [170.313168] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.313177] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [170.313362] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [170.313424] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.313431] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.313909] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.314139] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.314583] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.314768] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.314775] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.314927] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [170.317998] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.318006] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [170.318188] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [170.318349] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:112:HDMI-A-1] EDID override reset
<7> [170.318379] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.318386] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.318873] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.319103] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.319569] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.319782] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.319788] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.319951] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [170.323006] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.323014] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [170.323196] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [170.323374] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:118:DP-2] EDID override reset
<7> [170.323405] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [170.323412] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [170.323698] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [170.324019] [drm:status_store] [CONNECTOR:124:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [170.324029] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [170.324040] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [170.324569] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.324751] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [170.325117] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.325306] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.325313] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.325495] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [170.328939] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.328951] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [170.329232] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [170.329318] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [170.329327] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [170.329865] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.330098] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [170.330806] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.331075] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.331083] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.331310] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [170.334612] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.334621] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [170.334878] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [170.335097] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:124:HDMI-A-2] EDID override reset
<7> [170.335139] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [170.335148] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [170.335649] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.335874] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [170.336287] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.336563] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.336572] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.336792] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [170.340056] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.340065] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [170.340321] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<6> [170.341531] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [170.341808] [drm:status_store] [CONNECTOR:112:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [170.341819] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.341831] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.342727] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.342969] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.343411] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.343702] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.343713] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.343934] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [170.347430] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.347441] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [170.347746] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [170.347859] [drm:status_store] [CONNECTOR:124:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [170.347869] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [170.347880] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [170.348399] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.348646] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [170.349086] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.349347] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.349356] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.349598] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [170.352990] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.353001] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [170.353261] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [170.353367] [drm:status_store] [CONNECTOR:95:eDP-1] force updated from 0 to 0 or reprobing
<7> [170.353378] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [170.353389] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [170.354443] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [170.354692] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [170.354920] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [170.355148] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [170.355414] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [170.355425] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [170.355434] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [170.355736] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [170.355974] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [170.357153] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [170.357385] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [170.358574] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [170.358585] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [170.358596] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [170.359068] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [170.382327] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [170.382337] [drm:drm_client_modeset_probe]
<7> [170.382420] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [170.382431] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [170.383465] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [170.383739] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [170.383967] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [170.384193] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [170.384482] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [170.384495] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [170.384504] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [170.384602] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [170.384834] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [170.386555] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [170.386787] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [170.388040] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [170.388050] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [170.388061] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [170.388072] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [170.388083] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [170.388402] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [170.388412] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [170.388422] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [170.388987] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.389230] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [170.389681] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [170.389954] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.389964] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.390186] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [170.393599] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [170.393609] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [170.393893] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [170.393904] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [170.393915] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [170.394220] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [170.394229] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [170.394239] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [170.394775] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.395010] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [170.395447] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [170.395732] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.395742] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [170.395962] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [170.399351] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [170.399362] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [170.399665] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [170.399676] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [170.399683] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [170.399690] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [170.399696] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [170.399702] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [170.399767] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [170.399786] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [170.399793] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [170.399799] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [170.399805] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [170.399835] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<6> [170.432646] Console: switching to colour frame buffer device 400x112
Created at 2024-02-18 22:37:50