Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 0.52 seconds
Igt-Version 
IGT-Version: 1.28-g21e9f1e49 (x86_64) (Linux: 6.8.0-rc5-linus-v6.8-rc5-gb401b621758e+ x86_64)
Out 
Using IGT_SRANDOM=1708290956 for randomisation
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.523s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.523s)
Dmesg
<6> [117.494171] Console: switching to colour dummy device 80x25
<6> [117.494258] [IGT] kms_force_connector_basic: executing
<7> [117.498228] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [117.499679] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [117.510576] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [117.511811] [drm:status_store] [CONNECTOR:114:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [117.511821] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [117.511829] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [117.563327] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [117.567347] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.567366] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [117.567781] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [117.571844] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.571864] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [117.572470] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [117.572641] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [117.572668] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [117.598462] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [117.599389] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [117.600183] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [117.601205] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [117.624391] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [117.648064] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.648086] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [117.648675] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [117.666737] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.666746] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [117.666990] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [117.667274] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [117.667347] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [117.667359] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [117.667678] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [117.719321] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [117.738155] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.738170] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [117.738521] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [117.755707] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.755715] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [117.755937] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [117.756195] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected
<6> [117.756322] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [117.756608] [drm:status_store] [CONNECTOR:114:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [117.756620] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [117.756628] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [117.756855] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [117.808323] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [117.827759] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.827785] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [117.828168] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [117.846568] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.846582] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [117.846792] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [117.847025] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] status updated from disconnected to connected
<7> [117.847558] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] probed modes :
<7> [117.847569] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [117.847579] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [117.847589] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [117.847598] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [117.847605] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [117.847682] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [117.847691] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [117.848032] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [117.899155] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [117.916375] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.916394] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [117.916676] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [117.932689] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [117.932701] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [117.932904] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [117.933281] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] probed modes :
<7> [117.933290] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [117.933299] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [117.933307] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [117.933314] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [117.933321] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [117.936539] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:114:HDMI-A-1] EDID override set
<7> [117.936572] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [117.936579] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [117.936820] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [117.937302] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:114:HDMI-A-1] ELD monitor IGT
<7> [117.937313] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:114:HDMI-A-1] ELD size 24, SAD count 0
<7> [117.988333] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [118.006072] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [118.006124] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [118.006762] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.006775] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [118.006790] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [118.006799] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [118.006812] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] probed modes :
<7> [118.006820] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [118.006828] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [118.006836] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.006844] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.006851] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.007161] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:114:HDMI-A-1] EDID override reset
<7> [118.007347] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [118.007361] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [118.007756] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [118.059374] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [118.083634] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.083671] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.084251] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [118.105092] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.105120] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [118.105353] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:114:HDMI-A-1] EDID changed, epoch counter 2
<7> [118.105374] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [118.105734] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [118.105743] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [118.105753] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [118.105760] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [118.105769] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] probed modes :
<7> [118.105775] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [118.105782] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [118.105788] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [118.105793] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [118.105799] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [118.106036] [drm:status_store] [CONNECTOR:114:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [118.106044] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [118.106052] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [118.106376] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [118.158183] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [118.175781] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.175795] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.176059] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [118.192618] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.192631] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [118.192907] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [118.193163] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] status updated from connected to disconnected
<7> [118.193188] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [118.193756] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [118.193768] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [118.194084] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [118.246175] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [118.262654] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.262667] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.262910] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [118.278873] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.278885] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [118.279169] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [118.279468] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected
<6> [118.279655] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [118.279895] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [118.281171] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:95:DP-1] EDID override reset
<7> [118.281204] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [118.281212] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [118.281479] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [118.282089] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [118.282725] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [118.283424] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [118.284418] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [118.284695] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [118.285688] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.287584] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.289381] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.291328] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.293368] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.295339] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.297363] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.299177] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.300959] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.301937] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [118.303037] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [118.303790] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [118.304400] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [118.304585] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:108:DP-2] EDID override reset
<7> [118.304615] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2]
<7> [118.304621] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [118.304905] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] disconnected
<7> [118.305134] [drm:status_store] [CONNECTOR:114:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [118.305143] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [118.305152] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [118.356184] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [118.359482] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.359491] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.359718] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [118.362771] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.362779] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [118.363009] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [118.363077] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [118.363084] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [118.406394] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [118.406719] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [118.406994] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [118.407337] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [118.414317] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [118.430318] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.430327] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.430528] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [118.445892] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.445899] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [118.446130] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [118.446355] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:114:HDMI-A-1] EDID override reset
<7> [118.446390] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [118.446397] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [118.497324] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [118.515636] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.515651] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.516009] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [118.533713] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.533722] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [118.533980] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [118.534236] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected
<6> [118.534864] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [118.535055] [drm:status_store] [CONNECTOR:114:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [118.535064] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [118.535071] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [118.535336] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [118.587323] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [118.605540] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.605554] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.605855] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [118.624608] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.624617] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [118.624846] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [118.625087] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [118.625569] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [118.626450] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [118.626814] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [118.627516] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [118.628807] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [118.628822] [drm:drm_client_modeset_probe]
<7> [118.629272] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [118.629314] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [118.629752] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [118.631129] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [118.631421] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [118.632535] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.634204] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.636030] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.637800] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.639695] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.641600] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.643522] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.645440] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.647464] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [118.648466] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [118.649571] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [118.650392] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [118.651042] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [118.651053] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2]
<7> [118.651060] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [118.651358] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] disconnected
<7> [118.651368] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [118.651378] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [118.703325] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [118.707183] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.707199] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [118.707557] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [118.711265] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [118.711279] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [118.711654] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [118.711667] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [118.711689] [drm:drm_client_modeset_probe] connector 95 enabled? no
<7> [118.711696] [drm:drm_client_modeset_probe] connector 108 enabled? no
<7> [118.711702] [drm:drm_client_modeset_probe] connector 114 enabled? no
<7> [118.711970] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [118.712010] [drm:drm_client_modeset_probe] picking CRTCs for 1024x768 config
<6> [118.716303] Console: switching to colour frame buffer device 128x48
Created at 2024-02-18 22:37:51