Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 1.31 seconds
Igt-Version 
IGT-Version: 1.28-g21e9f1e49 (x86_64) (Linux: 6.8.0-rc5-linus-v6.8-rc5-gb401b621758e+ x86_64)
Out 
Using IGT_SRANDOM=1708290533 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff888126ddb4b0 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     intel_atomic_commit_tail+0xaef/0xf80 [i915]
     intel_atomic_commit+0x321/0x370 [i915]
     drm_atomic_commit+0x92/0xc0
     drm_atomic_helper_set_config+0x77/0xc0
     drm_mode_setcrtc+0x1f4/0x740
     drm_ioctl_kernel+0xa8/0x100
     drm_ioctl+0x223/0x430
     __x64_sys_ioctl+0x79/0xb0
     do_syscall_64+0x6f/0x140
     entry_SYSCALL_64_after_hwframe+0x6e/0x76
Subtest basic-rte: SUCCESS (1.315s)
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff888126ddb4b0 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     __gt_park+0x154/0x210 [i915]
     ____intel_wakeref_put_last+0x1d/0x80 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x76/0x80 [i915]
     i915_forcewake_release+0x1d/0x40 [i915]
     full_proxy_release+0x39/0xa0
     __fput+0xa1/0x2d0
     __x64_sys_close+0x39/0x80
     do_syscall_64+0x6f/0x140
     entry_SYSCALL_64_after_hwframe+0x6e/0x76
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (1.315s)
Dmesg
<6> [109.978698] Console: switching to colour dummy device 80x25
<6> [109.978737] [IGT] kms_pm_rpm: executing
<6> [109.981802] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [109.981847] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [109.987557] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [109.987566] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [109.987791] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [109.988370] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [109.988375] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [109.988589] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [109.988950] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [109.988961] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [109.989145] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [109.989493] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [109.989496] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [109.989655] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [109.990128] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [109.990131] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [109.990266] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [109.990279] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [109.990282] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [109.990420] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [109.990432] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [109.990435] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [109.990589] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [109.990601] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [109.990603] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [109.990754] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [109.990775] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [109.990777] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [109.990911] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [109.990990] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [109.990993] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [109.991136] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [109.991182] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [109.991184] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [109.991338] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [109.991384] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [109.991387] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [109.991538] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [110.138335] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [110.139356] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [110.140248] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [110.141450] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.992515] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [110.998054] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [111.000067] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [111.001270] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [111.001555] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [111.001736] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [111.001834] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [111.001971] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [111.028188] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [111.028695] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [111.029694] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [111.030605] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [111.031559] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [111.032553] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [111.033429] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [111.034208] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [111.034799] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [111.036335] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [111.038855] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [111.039072] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [111.042414] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [111.043049] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [111.043426] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [111.043532] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [111.043647] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [111.043913] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [111.044425] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [111.044582] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.044731] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [111.044894] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [111.044940] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [111.045195] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [111.045273] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [111.063315] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [111.063906] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [111.064522] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [111.065417] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [111.066258] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [111.067451] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [111.068663] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [111.069730] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [111.070409] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [111.070934] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [111.071344] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [111.071733] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [111.146222] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [111.159449] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [111.159950] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [111.160928] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [111.161895] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [111.162891] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [111.163893] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [111.164214] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [111.164587] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [111.164698] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [111.164889] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [111.166493] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [111.166596] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [111.169350] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [111.169875] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [111.169993] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [111.170159] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [111.170467] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [111.170753] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [111.170914] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.171081] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [111.171291] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [111.171248] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [111.171532] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [111.171614] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [111.189271] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [111.189918] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [111.190591] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [111.191575] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [111.192390] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [111.193538] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [111.194900] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [111.195532] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [111.195809] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [111.196044] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [111.196185] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [111.196347] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [111.285253] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [111.285773] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [111.286780] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [111.288107] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [111.289608] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [111.290022] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [111.290181] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [111.290565] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [111.290686] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [111.290875] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [111.292487] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [111.292583] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [111.295352] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [111.295874] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [111.295984] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<6> [111.296665] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [111.296688] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [111.296761] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [111.297074] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [111.297352] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [111.297505] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.297655] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [111.297819] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [111.298009] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [111.298114] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [111.298184] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [111.420343] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [111.421378] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [111.422294] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [111.423496] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [111.424460] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [111.425722] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [111.426380] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [111.426943] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [111.427280] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [111.427517] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [111.427887] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [111.428291] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [111.514770] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [111.515513] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [111.516464] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [111.517776] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [111.518917] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [111.519950] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [111.520853] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [111.522506] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [111.523068] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [111.523625] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [111.525602] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [111.525788] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [111.529572] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [111.530529] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [111.530726] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [111.530965] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [111.531254] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [111.531672] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [111.531827] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<6> [111.532045] [IGT] kms_pm_rpm: exiting, ret=0
<7> [111.531996] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [111.532197] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<6> [111.533813] Console: switching to colour frame buffer device 128x48
Created at 2024-02-18 22:37:50