Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 0.27 seconds
Igt-Version 
IGT-Version: 1.28-g17a41dcf1 (x86_64) (Linux: 6.8.0-rc4-linus-v6.8-rc4-g841c35169323+ x86_64)
Out 
Using IGT_SRANDOM=1707683269 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff88811378b4b0 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     intel_atomic_commit_tail+0xaef/0xf80 [i915]
     intel_atomic_commit+0x321/0x370 [i915]
     drm_atomic_commit+0x95/0xc0
     drm_atomic_helper_set_config+0x77/0xc0
     drm_mode_setcrtc+0x202/0x710
     drm_ioctl_kernel+0xab/0x100
     drm_ioctl+0x223/0x430
     __x64_sys_ioctl+0x7c/0xb0
     do_syscall_64+0x72/0x140
     entry_SYSCALL_64_after_hwframe+0x6e/0x76
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.269s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.269s)
Dmesg
<6> [80.475802] Console: switching to colour dummy device 80x25
<6> [80.475853] [IGT] kms_pm_rpm: executing
<7> [80.483273] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [80.487655] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [80.487662] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [80.488031] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [80.488446] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [80.488451] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [80.489652] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [80.490686] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [80.491365] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [80.491819] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [80.491825] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [80.492258] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [80.492374] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [80.492788] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [80.492932] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [80.492936] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [80.493077] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [80.497337] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [80.497342] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [80.497466] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [80.497811] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [80.497816] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [80.497971] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [80.497987] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [80.497991] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [80.499151] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [80.500276] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [80.501145] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [80.501163] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [80.501167] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [80.501594] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [80.501736] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [80.502147] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [80.502298] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [80.502302] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [80.502414] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [80.506546] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [80.506550] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [80.506690] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [80.506737] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [80.506741] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [80.506903] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [80.506957] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [80.506976] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [80.508163] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [80.509312] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [80.510156] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [80.510205] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [80.510209] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [80.510636] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [80.510778] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [80.511191] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [80.511343] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [80.511347] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [80.511459] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [80.515481] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [80.515486] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [80.515609] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [80.714880] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [80.715477] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [80.716043] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [80.716716] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [80.717646] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.564959] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.576481] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [91.600855] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.610387] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.611730] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [91.612039] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.612460] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.613394] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.614533] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [91.614826] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [91.614817] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [91.615043] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [91.616512] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.617694] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.618552] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [91.619220] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.619364] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.619771] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.619929] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.619933] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.620050] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.624179] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.624184] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.624431] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [91.738821] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [91.739130] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.739382] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.739627] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.740374] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.741218] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.745687] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [91.825640] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [91.838117] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [91.850474] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.860097] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.861009] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.861379] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.862071] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.862937] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [91.863352] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [91.863579] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [91.863805] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [91.865199] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.866168] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.866810] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [91.867353] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.867558] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.868048] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.868293] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.868301] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.868503] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.872751] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.872756] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.873055] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [91.986809] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [91.987041] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.987226] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.987406] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.988081] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.988323] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.991717] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [92.085902] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [92.091253] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [92.091520] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [92.091792] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [92.092332] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [92.093169] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [92.093468] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [92.093789] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<6> [92.094483] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [92.095205] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [92.096033] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [92.096829] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [92.097293] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.097419] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [92.097800] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.097956] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.097962] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [92.098081] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [92.102191] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.102196] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<6> [92.102735] [IGT] kms_pm_rpm: exiting, ret=0
<6> [92.103753] Console: switching to colour frame buffer device 128x48
Created at 2024-02-11 22:21:45