Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 0.42 seconds
Igt-Version 
IGT-Version: 1.28-gbf075a74e (x86_64) (Linux: 6.8.0-rc3-linus-v6.8-rc3-g54be6c6c5ae8+ x86_64)
Out 
Using IGT_SRANDOM=1707051531 for randomisation
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.416s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.416s)
Dmesg
<6> [112.374508] Console: switching to colour dummy device 80x25
<6> [112.374539] [IGT] kms_force_connector_basic: executing
<7> [112.377009] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [112.377892] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [112.384529] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [112.385396] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [112.385405] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.385412] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.385617] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [112.385644] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.385649] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.385831] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [112.385870] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.385873] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.386059] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<6> [112.386107] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [112.386215] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [112.386219] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.386224] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.437357] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [112.437452] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [112.438469] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [112.439318] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [112.458726] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.458740] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.458866] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [112.476433] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.476443] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [112.476559] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] status updated from disconnected to connected
<7> [112.476601] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [112.476604] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.476609] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.476612] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.476615] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.476617] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.476653] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.476657] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.528509] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [112.549647] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.549656] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.549796] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [112.566822] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.566828] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [112.566911] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.567064] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [112.567069] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.567074] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.567076] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.567079] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.567081] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.567254] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:249:HDMI-A-1] EDID override set
<7> [112.567273] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.567277] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.567396] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.567529] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD monitor IGT
<7> [112.567533] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD size 24, SAD count 0
<7> [112.618937] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [112.638395] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [112.638408] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.638574] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.638580] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [112.638585] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.638588] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [112.638592] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [112.638595] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [112.638598] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [112.638600] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [112.638603] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.638605] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.638608] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.638714] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:249:HDMI-A-1] EDID override set
<7> [112.638730] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.638733] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.638828] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.638937] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD monitor IGT
<7> [112.638940] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD size 24, SAD count 0
<7> [112.638943] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:249:HDMI-A-1] EDID changed, epoch counter 4
<7> [112.689769] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [112.711845] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [112.711860] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.712094] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [112.712101] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [112.712108] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [112.712111] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [112.712115] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [112.712119] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.712122] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.712126] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.712234] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:249:HDMI-A-1] EDID override reset
<7> [112.712255] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.712259] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.712398] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.762933] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [112.783428] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.783435] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [112.783527] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [112.800587] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [112.800592] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [112.800672] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:249:HDMI-A-1] EDID changed, epoch counter 5
<7> [112.800680] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.800804] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [112.800808] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [112.800811] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [112.800814] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [112.800817] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [112.800820] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [112.800822] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [112.800824] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [112.800826] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [112.800828] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [112.800927] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [112.800931] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.800935] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.801056] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.801399] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] status updated from connected to disconnected
<7> [112.801408] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [112.801440] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.801443] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.801887] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<6> [112.801944] [IGT] kms_force_connector_basic: finished subtest prune-stale-modes, SUCCESS
<7> [112.802049] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [112.802598] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:236:DP-1] EDID override reset
<7> [112.802610] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [112.802613] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [112.802934] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [112.803017] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [112.803103] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.803107] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.803454] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [112.803474] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.803477] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.803624] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [112.803677] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:249:HDMI-A-1] EDID override reset
<7> [112.803688] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.803690] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.804005] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [112.804079] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:255:DP-2] EDID override reset
<7> [112.804089] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [112.804092] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [112.804536] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [112.804595] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:264:DP-3] EDID override reset
<7> [112.804605] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [112.804607] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [112.805061] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<6> [112.805256] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [112.805330] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [112.805333] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.805336] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.805659] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [112.805792] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [112.824593] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [112.824879] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [112.825199] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [112.825203] [drm:drm_client_modeset_probe]
<7> [112.825225] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [112.825229] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [112.825384] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [112.825387] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [112.825391] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.825545] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [112.825548] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [112.825551] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [112.825723] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [112.825726] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [112.825729] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [112.825894] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [112.825896] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [112.825899] [drm:drm_client_modeset_probe] connector 236 enabled? no
<7> [112.825902] [drm:drm_client_modeset_probe] connector 249 enabled? no
<7> [112.825903] [drm:drm_client_modeset_probe] connector 255 enabled? no
<7> [112.825905] [drm:drm_client_modeset_probe] connector 264 enabled? no
<7> [112.825926] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [112.825933] [drm:drm_client_modeset_probe] picking CRTCs for 1024x768 config
<6> [112.826969] Console: switching to colour frame buffer device 128x48
Created at 2024-02-04 14:26:35