Results for igt@kms_frontbuffer_tracking@basic

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 2.26 seconds
Igt-Version 
IGT-Version: 1.28-g814cd9883 (x86_64) (Linux: 6.8.0-rc2-linus-v6.8-rc2-g41bccc98fb79+ x86_64)
Out 
Using IGT_SRANDOM=1706490986 for randomisation
Opened device: /dev/dri/card0
FBC last action not supported
Can't test PSR: no usable eDP screen.
Can't test DRRS: no usable screen.
Starting subtest: basic
Subtest basic: SUCCESS (2.260s)
Err 
Starting subtest: basic
Subtest basic: SUCCESS (2.260s)
Dmesg
<6> [257.013736] Console: switching to colour dummy device 80x25
<6> [257.014906] [IGT] kms_frontbuffer_tracking: executing
<7> [257.282119] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [257.282764] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [257.283133] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [257.289366] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [257.289379] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [257.289605] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [257.289788] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [257.290258] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [257.290538] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [257.291030] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [257.291317] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [257.291327] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [257.291606] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [257.293428] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [257.293438] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [257.293718] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [257.294043] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [257.294819] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [257.294879] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [257.345915] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [257.361902] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [257.361912] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [257.362112] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [257.377888] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [257.377897] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [257.378105] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [257.378655] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1]
<7> [257.378663] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [257.378889] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected
<7> [257.379785] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [257.379796] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [257.380369] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [257.380647] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [257.381168] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [257.381446] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [257.381455] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [257.381727] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [257.383535] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [257.383545] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [257.383815] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [257.384735] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [257.384746] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [257.385317] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [257.385595] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [257.386109] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [257.386385] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [257.386394] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [257.386666] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [257.388466] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [257.388476] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [257.388758] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [257.389715] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2]
<7> [257.389726] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [257.390071] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected
<7> [257.390917] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3]
<7> [257.390928] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [257.391218] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected
<7> [257.391740] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [257.391753] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [257.391762] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [257.391905] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [257.391914] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [257.391951] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [257.391961] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [257.392269] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [257.392549] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [257.393094] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [257.393370] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [257.393889] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [257.394180] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [257.394189] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [257.394465] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [257.396252] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [257.396262] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [257.396539] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [257.396817] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [257.397202] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 2 or reprobing
<7> [257.397214] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [257.397224] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] status updated from disconnected to connected
<7> [257.397634] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [257.398010] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [257.398523] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [257.398853] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [257.398881] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [257.399180] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [257.401183] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [257.401211] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [257.401626] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [257.401637] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [257.401649] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [257.401660] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [257.401670] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [257.401681] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [257.401762] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [257.402077] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [257.402368] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [257.402872] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [257.403165] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [257.403187] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [257.403474] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [257.405130] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [257.405152] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [257.405552] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [257.405560] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [257.405571] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [257.405580] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [257.405589] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [257.405598] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [257.405642] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [257.405652] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [257.458304] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [257.474972] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [257.474989] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [257.475522] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [257.491883] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [257.491892] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [257.492094] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [257.492142] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1]
<7> [257.492149] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [257.492350] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected
<7> [257.492373] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [257.492379] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [257.492718] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [257.492957] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [257.493391] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [257.493584] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [257.493590] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [257.493778] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [257.495232] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [257.495240] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [257.495435] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [257.495463] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [257.495470] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [257.495876] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [257.496122] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [257.496506] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [257.496709] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [257.496714] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [257.496926] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [257.498397] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [257.498405] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [257.498599] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [257.498626] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2]
<7> [257.498633] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [257.498884] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected
<7> [257.498924] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3]
<7> [257.498934] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [257.499153] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected
<7> [257.500636] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:99]
<7> [257.500735] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:100]
<7> [257.500902] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:101]
<7> [257.501067] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:102]
<7> [257.501203] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:103]
<6> [257.503906] [IGT] kms_frontbuffer_tracking: starting subtest basic
<7> [257.504045] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [257.506593] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:99]
<7> [257.506686] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:100]
<7> [257.506871] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:101]
<7> [257.507026] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:102]
<7> [257.507162] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:103]
<7> [257.507329] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:104]
<7> [257.548394] [drm:drm_mode_setcrtc] [CRTC:45:pipe A]
<7> [257.548461] [drm:drm_mode_setcrtc] [CONNECTOR:61:LVDS-1]
<7> [257.566968] [drm:drm_mode_setcrtc] [CRTC:60:pipe B]
<7> [257.569117] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [257.569560] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [257.648478] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:104] from all active usage due to RMFB ioctl
<7> [257.648537] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:31:primary A] because [FB:104] is removed
<7> [257.666613] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:96]
<7> [257.666945] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:104]
<7> [257.667193] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:107]
<7> [257.667428] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:108]
<7> [257.832108] [drm:drm_mode_setcrtc] [CRTC:45:pipe A]
<7> [257.832245] [drm:drm_mode_setcrtc] [CONNECTOR:61:LVDS-1]
<7> [257.867151] [drm:drm_mode_setcrtc] [CRTC:60:pipe B]
<7> [257.870041] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [257.870392] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [257.948303] [drm:drm_mode_setcrtc] [CRTC:45:pipe A]
<7> [257.948446] [drm:drm_mode_setcrtc] [CONNECTOR:61:LVDS-1]
<7> [257.965246] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [258.048207] [drm:drm_mode_setcrtc] [CRTC:45:pipe A]
<7> [258.048288] [drm:drm_mode_setcrtc] [CONNECTOR:61:LVDS-1]
<7> [258.065054] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [258.148094] [drm:drm_mode_setcrtc] [CRTC:45:pipe A]
<7> [258.148155] [drm:drm_mode_setcrtc] [CONNECTOR:61:LVDS-1]
<7> [258.165191] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [258.248667] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:108] from all active usage due to RMFB ioctl
<7> [258.248707] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:31:primary A] because [FB:108] is removed
<7> [258.298196] [drm:drm_mode_setcrtc] [CRTC:45:pipe A]
<7> [258.298310] [drm:drm_mode_setcrtc] [CONNECTOR:61:LVDS-1]
<7> [258.334285] [drm:drm_mode_setcrtc] [CRTC:60:pipe B]
<7> [258.336517] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [258.336935] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [258.348315] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [258.431723] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [258.515223] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:104]
<7> [258.518705] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [258.519640] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [258.598029] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [258.682307] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [258.683073] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [258.764653] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [258.850073] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [258.859610] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [258.931206] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [259.031000] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [259.031300] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [259.114305] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [259.213638] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [259.220365] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [259.297587] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [259.384191] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [259.397579] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [259.480954] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [259.571118] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [259.584585] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [259.664333] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [259.747155] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:104] from all active usage due to RMFB ioctl
<7> [259.747309] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:31:primary A] because [FB:104] is removed
<6> [259.765235] [IGT] kms_frontbuffer_tracking: finished subtest basic, SUCCESS
<6> [259.767094] [IGT] kms_frontbuffer_tracking: exiting, ret=0
<7> [259.767523] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 2 to 0 or reprobing
<7> [259.767539] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [259.767554] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [259.767966] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [259.768264] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [259.768782] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [259.769107] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [259.769608] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [259.769963] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [259.769974] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [259.770268] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [259.772180] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [259.772192] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [259.772490] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [259.772780] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] status updated from connected to disconnected
<7> [259.772963] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [259.772972] [drm:drm_client_modeset_probe]
<7> [259.773095] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [259.773161] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [259.773176] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [259.773188] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [259.773302] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [259.773311] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [259.773324] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [259.773335] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [259.773656] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [259.773987] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [259.774448] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [259.774730] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [259.774742] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [259.775376] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [259.775577] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [259.775585] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [259.775779] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [259.777640] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [259.777650] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [259.777919] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [259.778171] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [259.778183] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [259.778191] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [259.829144] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [259.845898] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [259.845911] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [259.846133] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [259.861895] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [259.861905] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [259.862121] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [259.862132] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1]
<7> [259.862141] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [259.862356] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected
<7> [259.862364] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [259.862371] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [259.862749] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [259.862971] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [259.863351] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [259.863542] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [259.863549] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [259.863737] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [259.865362] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [259.865372] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [259.865571] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [259.865579] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [259.865586] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [259.865976] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [259.866185] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [259.866561] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [259.866753] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [259.866759] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [259.867005] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [259.868544] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [259.868552] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [259.868747] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [259.868755] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2]
<7> [259.868763] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [259.869025] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected
<7> [259.869037] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3]
<7> [259.869048] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [259.869270] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected
<7> [259.869276] [drm:drm_client_modeset_probe] connector 61 enabled? yes
<7> [259.869282] [drm:drm_client_modeset_probe] connector 65 enabled? no
<7> [259.869287] [drm:drm_client_modeset_probe] connector 68 enabled? no
<7> [259.869290] [drm:drm_client_modeset_probe] connector 76 enabled? no
<7> [259.869294] [drm:drm_client_modeset_probe] connector 81 enabled? no
<7> [259.869298] [drm:drm_client_modeset_probe] connector 85 enabled? no
<7> [259.869302] [drm:drm_client_modeset_probe] connector 89 enabled? no
<7> [259.869306] [drm:drm_client_modeset_probe] connector 93 enabled? no
<7> [259.869324] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [259.869337] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61
<7> [259.869341] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0
<7> [259.869346] [drm:drm_client_modeset_probe] found mode 1366x768
<7> [259.869349] [drm:drm_client_modeset_probe] picking CRTCs for 1366x768 config
<7> [259.869370] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)
<7> [259.913705] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [259.913736] [drm:drm_client_modeset_probe]
<7> [259.914030] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [259.914049] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [259.914062] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [259.914179] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [259.914189] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [259.914203] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [259.914214] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [259.914460] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [259.914655] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [259.915040] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [259.915234] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [259.915578] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [259.915770] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [259.915776] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [259.916035] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [259.917579] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [259.917585] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [259.917777] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [259.918026] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [259.918037] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [259.918047] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [259.969169] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [259.985918] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [259.985931] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [259.986168] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [260.001910] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [260.001917] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [260.002131] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [260.002140] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1]
<7> [260.002148] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [260.002362] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected
<7> [260.002367] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [260.002373] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [260.002722] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [260.002964] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [260.003374] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [260.003563] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [260.003568] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [260.003756] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [260.005590] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [260.005597] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [260.005796] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [260.005803] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [260.005808] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [260.006198] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [260.006404] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [260.006780] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [260.006996] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [260.007002] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [260.007232] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [260.008760] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [260.008766] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [260.008990] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [260.008996] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2]
<7> [260.009002] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [260.009249] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected
<7> [260.009255] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3]
<7> [260.009260] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [260.009455] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected
<7> [260.009460] [drm:drm_client_modeset_probe] connector 61 enabled? yes
<7> [260.009465] [drm:drm_client_modeset_probe] connector 65 enabled? no
<7> [260.009468] [drm:drm_client_modeset_probe] connector 68 enabled? no
<7> [260.009470] [drm:drm_client_modeset_probe] connector 76 enabled? no
<7> [260.009473] [drm:drm_client_modeset_probe] connector 81 enabled? no
<7> [260.009476] [drm:drm_client_modeset_probe] connector 85 enabled? no
<7> [260.009478] [drm:drm_client_modeset_probe] connector 89 enabled? no
<7> [260.009481] [drm:drm_client_modeset_probe] connector 93 enabled? no
<7> [260.009509] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [260.009520] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61
<7> [260.009524] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0
<7> [260.009527] [drm:drm_client_modeset_probe] found mode 1366x768
<7> [260.009529] [drm:drm_client_modeset_probe] picking CRTCs for 1366x768 config
<7> [260.009548] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)
<6> [260.029797] Console: switching to colour frame buffer device 170x48
Created at 2024-01-29 02:30:06