Result:
git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0
| Detail | Value |
|---|---|
| Duration | 0.22 seconds |
| Igt-Version |
IGT-Version: 1.28-g814cd9883 (x86_64) (Linux: 6.8.0-rc2-linus-v6.8-rc2-g41bccc98fb79+ x86_64) |
| Out |
Using IGT_SRANDOM=1706490792 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff8881078534b0 has 1/1 users at
track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
__intel_display_power_put_async+0x3d/0x160 [i915]
intel_atomic_commit_tail+0xaef/0xf80 [i915]
intel_atomic_commit+0x321/0x370 [i915]
drm_atomic_commit+0x92/0xc0
drm_atomic_helper_set_config+0x77/0xc0
drm_mode_setcrtc+0x1ff/0x710
drm_ioctl_kernel+0xa8/0x100
drm_ioctl+0x223/0x430
__x64_sys_ioctl+0x79/0xb0
do_syscall_64+0x6f/0x140
entry_SYSCALL_64_after_hwframe+0x6e/0x76
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.222s)
|
| Err |
Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (0.222s) |
| Dmesg |
<6> [94.503157] Console: switching to colour dummy device 80x25
<6> [94.503217] [IGT] kms_pm_rpm: executing
<7> [94.506037] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [94.510834] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [94.510842] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [94.511227] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [94.511334] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [94.511631] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [94.511762] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [94.511767] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.511871] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [94.514878] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [94.514882] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [94.515027] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [94.515563] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [94.515568] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [94.515902] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [94.516019] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [94.516309] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [94.516438] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.516442] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.516545] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [94.519364] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.519369] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [94.519490] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [94.519980] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [94.519986] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [94.520134] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [94.520486] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [94.520491] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [94.520823] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [94.520929] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [94.521237] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [94.521366] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [94.521370] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.521475] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [94.524336] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [94.524341] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [94.524461] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [94.524480] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [94.524484] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [94.524813] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [94.524918] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [94.525219] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [94.525348] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.525352] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.525455] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [94.528285] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.528289] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [94.528408] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [94.528427] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [94.528431] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [94.528574] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [94.528601] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [94.528605] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [94.528934] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [94.529052] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [94.529348] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [94.529476] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [94.529480] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.529584] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [94.532391] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [94.532395] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [94.532514] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [94.532558] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [94.532562] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [94.532891] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [94.533008] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [94.533295] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [94.533422] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.533426] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [94.533529] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [94.536344] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [94.536348] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [94.536467] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [94.536528] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [94.536532] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [94.536676] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [94.570091] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [94.570243] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [94.570377] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [94.674172] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [95.541331] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [95.547650] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [95.551199] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [95.574302] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [95.597250] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [95.600077] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [95.601809] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [95.601116] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [95.602588] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [95.603779] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [95.605232] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [95.605213] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [95.607584] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [95.607718] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [95.608031] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [95.608173] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [95.608178] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [95.608284] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [95.611156] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [95.611160] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [95.611300] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [95.611651] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [95.611755] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [95.612044] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [95.612175] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [95.612179] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [95.612284] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [95.615122] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [95.615127] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [95.615279] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [95.615639] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [95.633126] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [95.633266] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [95.633397] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [95.634002] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [95.634313] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [95.638404] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [95.642075] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [95.716784] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [95.752642] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [95.765055] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [95.778724] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [95.779468] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [95.779888] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [95.780295] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [95.780987] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [95.782501] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [95.783121] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [95.783098] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [95.783455] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [95.784059] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [95.784422] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [95.784435] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [95.784725] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [95.788336] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [95.788351] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [95.788701] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [95.789418] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [95.789711] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [95.790246] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [95.790586] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [95.790598] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [95.790884] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [95.794430] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [95.794443] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [95.795299] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [95.795312] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [95.814115] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [95.814502] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [95.814870] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [95.815743] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [95.816587] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [95.818802] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [95.824984] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [95.909743] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [95.930128] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [95.931852] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [95.932605] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [95.933521] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [95.934513] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [95.936105] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [95.937152] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [95.938026] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<6> [95.939195] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [95.939188] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [95.940238] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [95.940275] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [95.941187] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [95.947361] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [95.947392] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [95.948138] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [95.949127] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [95.949710] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [95.950566] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [95.951290] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [95.951314] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [95.951888] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [95.956038] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [95.956056] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [95.956515] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [95.959631] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [95.960449] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [95.973669] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [96.042105] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [96.042483] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [96.042881] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [96.043800] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [96.145067] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [96.145207] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [96.145623] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [96.146307] [IGT] kms_pm_rpm: exiting, ret=0
<6> [96.147567] Console: switching to colour frame buffer device 128x48
|