Results for igt@kms_pm_rpm@basic-rte

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 1.32 seconds
Igt-Version 
IGT-Version: 1.28-g814cd9883 (x86_64) (Linux: 6.8.0-rc2-linus-v6.8-rc2-g41bccc98fb79+ x86_64)
Out 
Using IGT_SRANDOM=1706490784 for randomisation
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff8881141934b0 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     intel_atomic_commit_tail+0xaef/0xf80 [i915]
     intel_atomic_commit+0x321/0x370 [i915]
     drm_atomic_commit+0x92/0xc0
     drm_atomic_helper_set_config+0x77/0xc0
     drm_mode_setcrtc+0x1ff/0x710
     drm_ioctl_kernel+0xa8/0x100
     drm_ioctl+0x223/0x430
     __x64_sys_ioctl+0x79/0xb0
     do_syscall_64+0x6f/0x140
     entry_SYSCALL_64_after_hwframe+0x6e/0x76
Subtest basic-rte: SUCCESS (1.317s)
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
ref_tracker: 0000:00:02.0@ffff8881141934b0 has 1/1 users at
     track_intel_runtime_pm_wakeref.part.0+0x30/0x60 [i915]
     __intel_display_power_put_async+0x3d/0x160 [i915]
     __gt_park+0x154/0x210 [i915]
     ____intel_wakeref_put_last+0x1d/0x80 [i915]
     intel_gt_pm_debugfs_forcewake_user_release+0x76/0x80 [i915]
     i915_forcewake_release+0x1d/0x40 [i915]
     full_proxy_release+0x39/0xa0
     __fput+0xa1/0x2d0
     __x64_sys_close+0x39/0x80
     do_syscall_64+0x6f/0x140
     entry_SYSCALL_64_after_hwframe+0x6e/0x76
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (1.317s)
Dmesg
<6> [114.650017] Console: switching to colour dummy device 80x25
<6> [114.650985] [IGT] kms_pm_rpm: executing
<6> [114.653797] [IGT] kms_pm_rpm: starting subtest basic-rte
<7> [114.653869] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [114.661907] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [114.661921] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [114.662165] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [114.662632] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [114.662638] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [114.662844] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [114.663299] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [114.663305] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [114.663536] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [114.663972] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [114.663977] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [114.664242] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [114.664738] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [114.664748] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [114.664972] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [114.664987] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [114.664991] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [114.665161] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [114.665174] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [114.665176] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [114.665338] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [114.665350] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [114.665352] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [114.665512] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [114.665534] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [114.665536] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [114.665672] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [114.665724] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [114.665726] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [114.665865] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [114.665910] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [114.665912] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [114.666080] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [114.666127] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [114.666130] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [114.666285] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [114.808387] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [114.809404] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.810328] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [114.811525] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.667325] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.668590] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.670608] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.672165] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.672431] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.672636] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.672733] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.672860] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.699269] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.699771] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.700769] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.701718] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.702671] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [115.703656] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [115.704523] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.705328] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.705903] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.706612] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.711125] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.711327] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.714497] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.715147] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.715762] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [115.715869] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.715986] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.716282] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.716852] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [115.717007] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.717135] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [115.717196] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [115.717376] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [115.717697] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [115.717793] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [115.735362] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.735898] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.736445] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.737298] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.737874] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.739135] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.740389] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.740978] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.741347] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.741574] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.741710] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.741876] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.818619] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [115.831992] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.832677] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.833587] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.834510] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.835492] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [115.836463] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [115.836629] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.836980] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.837117] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.837323] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.838947] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.839051] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.842126] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.842769] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.842886] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.843058] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.843360] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.843648] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [115.843813] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.843970] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [115.844191] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [115.844158] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [115.844474] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [115.844598] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [115.862358] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.863106] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.863769] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.864761] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.865595] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.866470] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.867822] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.868153] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.868569] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.868796] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.868932] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.869105] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.958538] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.959161] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.960151] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.961102] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.962072] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [115.963071] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [115.963458] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.963938] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.964096] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.964332] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.966330] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.966471] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.969583] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.970247] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.970485] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.970649] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [115.970852] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<6> [115.971108] [IGT] kms_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [115.971129] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [115.971089] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [115.971588] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [115.972257] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.972566] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.972777] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [115.972852] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [115.972920] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [116.090386] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [116.091408] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [116.092326] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [116.093531] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [116.094487] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [116.095701] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [116.096359] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [116.096920] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [116.097264] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [116.097504] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [116.097896] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [116.098305] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [116.189696] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [116.190704] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [116.191591] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [116.192368] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [116.193257] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [116.193886] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))
<7> [116.194488] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [116.195071] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [116.195473] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [116.196393] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [116.199669] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [116.199847] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [116.203123] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [116.203984] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [116.204219] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [116.204372] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [116.204655] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [116.205118] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [116.205275] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [116.205429] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [116.205599] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<6> [116.205823] [IGT] kms_pm_rpm: exiting, ret=0
<6> [116.206981] Console: switching to colour frame buffer device 128x48
Created at 2024-01-29 02:30:05