Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 0.37 seconds
Igt-Version 
IGT-Version: 1.28-g814cd9883 (x86_64) (Linux: 6.8.0-rc2-linus-v6.8-rc2-g41bccc98fb79+ x86_64)
Out 
Using IGT_SRANDOM=1706490781 for randomisation
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.370s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.370s)
Dmesg
<6> [111.558567] Console: switching to colour dummy device 80x25
<6> [111.558603] [IGT] kms_force_connector_basic: executing
<7> [111.561126] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [111.561743] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [111.572265] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [111.572882] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [111.572887] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.572892] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.573083] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [111.573122] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.573125] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.573281] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [111.573314] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.573316] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.573460] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<6> [111.573497] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [111.573586] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [111.573590] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.573593] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.625483] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [111.634545] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [111.634554] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [111.634652] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [111.641747] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [111.641752] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [111.641846] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] status updated from disconnected to connected
<7> [111.641984] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [111.641988] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [111.641994] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [111.641997] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [111.642000] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [111.642003] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [111.642050] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.642053] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.692592] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [111.701870] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [111.701881] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [111.702015] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [111.709134] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [111.709149] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [111.709342] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [111.709347] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [111.709353] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [111.709357] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [111.709360] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [111.709363] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [111.709571] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:249:HDMI-A-1] EDID override set
<7> [111.709596] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.709600] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.709757] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD monitor IGT
<7> [111.709762] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD size 24, SAD count 0
<7> [111.728196] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [111.728494] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [111.728736] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [111.761613] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [111.782647] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [111.782666] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [111.782916] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [111.782922] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [111.782929] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [111.782933] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [111.782938] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [111.782942] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [111.782946] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [111.782949] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [111.782952] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [111.782955] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [111.782959] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [111.783152] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:249:HDMI-A-1] EDID override set
<7> [111.783185] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.783190] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.783370] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [111.783571] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD monitor IGT
<7> [111.783576] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:249:HDMI-A-1] ELD size 24, SAD count 0
<7> [111.783581] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:249:HDMI-A-1] EDID changed, epoch counter 4
<7> [111.833765] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [111.854265] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [111.854284] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [111.854464] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [111.854468] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [111.854472] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [111.854474] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [111.854476] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [111.854479] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [111.854481] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [111.854483] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [111.854554] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:249:HDMI-A-1] EDID override reset
<7> [111.854569] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.854571] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.854672] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [111.905231] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 2
<7> [111.925120] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [111.925126] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [111.925234] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [111.942257] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [111.942262] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [111.942345] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:249:HDMI-A-1] EDID changed, epoch counter 5
<7> [111.942353] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [111.942482] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [111.942485] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [111.942490] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [111.942492] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [111.942496] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] probed modes :
<7> [111.942498] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [111.942501] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [111.942503] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [111.942505] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [111.942507] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [111.942618] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [111.942622] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.942626] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.942722] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [111.943046] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] status updated from connected to disconnected
<7> [111.943080] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [111.943114] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.943117] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.943549] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<6> [111.943609] [IGT] kms_force_connector_basic: finished subtest prune-stale-modes, SUCCESS
<7> [111.943703] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [111.944298] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:236:DP-1] EDID override reset
<7> [111.944312] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [111.944315] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [111.944641] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [111.944741] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [111.944744] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.944747] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.945219] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [111.945239] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.945242] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.945680] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [111.945740] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:249:HDMI-A-1] EDID override reset
<7> [111.945752] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.945754] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.946201] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [111.946267] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:255:DP-2] EDID override reset
<7> [111.946278] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [111.946280] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [111.946730] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [111.946794] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:264:DP-3] EDID override reset
<7> [111.946804] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [111.946807] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [111.947236] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<6> [111.947437] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [111.947507] [drm:status_store] [CONNECTOR:249:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [111.947510] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.947513] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.947852] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [111.947989] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [111.963896] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [111.964250] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [111.964556] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [111.964560] [drm:drm_client_modeset_probe]
<7> [111.964592] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1]
<7> [111.964597] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [111.964787] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:DP-1] disconnected
<7> [111.964792] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1]
<7> [111.964796] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [111.964990] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [111.964993] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2]
<7> [111.964997] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [111.965226] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:DP-2] disconnected
<7> [111.965233] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3]
<7> [111.965237] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [111.965448] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-3] disconnected
<7> [111.965452] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [111.965455] [drm:drm_client_modeset_probe] connector 236 enabled? no
<7> [111.965458] [drm:drm_client_modeset_probe] connector 249 enabled? no
<7> [111.965460] [drm:drm_client_modeset_probe] connector 255 enabled? no
<7> [111.965462] [drm:drm_client_modeset_probe] connector 264 enabled? no
<7> [111.965489] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [111.965498] [drm:drm_client_modeset_probe] picking CRTCs for 1024x768 config
<6> [111.967016] Console: switching to colour frame buffer device 128x48
Created at 2024-01-29 02:30:05