Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 0.02 seconds
Igt-Version 
IGT-Version: 1.28-gfa4ee7909 (x86_64) (Linux: 6.8.0-rc1-linus-v6.8-rc1-g6613476e225e+ x86_64)
Out 
Using IGT_SRANDOM=1705876803 for randomisation
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.021s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.021s)
Dmesg
<6> [268.494603] Console: switching to colour dummy device 80x25
<6> [268.495469] [IGT] kms_force_connector_basic: executing
<7> [268.677212] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [268.677885] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [268.678154] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [268.678867] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [268.678877] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.678886] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.679106] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.679338] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.679802] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.680010] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.680371] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.680572] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.680580] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.680773] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.682326] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.682335] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.682530] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.682726] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.682779] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.682786] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.682987] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.683180] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.683649] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.683843] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.684218] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.684432] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.684441] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.684662] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.686107] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.686115] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.686325] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.686550] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.686663] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.686669] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.686868] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.687059] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.687500] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.687693] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.688066] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.688282] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.688291] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.688508] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.689949] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.689957] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.690152] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.690396] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<6> [268.691064] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [268.691365] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 2 or reprobing
<7> [268.691380] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.691389] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] status updated from disconnected to connected
<7> [268.691720] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.691966] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.692507] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.692810] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.692835] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.693136] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.695141] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.695169] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.695646] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [268.695658] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [268.695671] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [268.695682] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [268.695692] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [268.695703] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [268.695789] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.696034] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.696369] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.696880] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.697173] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.697197] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.697548] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.699011] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.699027] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.699321] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [268.699331] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [268.699342] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [268.699351] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [268.699360] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [268.699369] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [268.699651] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:65:VGA-1] EDID override set
<7> [268.699683] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.699728] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD monitor IGT
<7> [268.699734] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD size 24, SAD count 0
<7> [268.699882] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [268.699889] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [268.699898] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [268.699904] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [268.699913] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [268.699917] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [268.699923] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [268.699928] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [268.699933] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [268.699938] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [268.699943] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [268.700101] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:65:VGA-1] EDID override set
<7> [268.700136] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.700174] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD monitor IGT
<7> [268.700180] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD size 24, SAD count 0
<7> [268.700186] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:65:VGA-1] EDID changed, epoch counter 60
<7> [268.700367] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [268.700379] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [268.700394] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [268.700401] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [268.700410] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [268.700419] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [268.700428] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [268.700436] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [268.700632] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:65:VGA-1] EDID override reset
<7> [268.700668] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.700877] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.701086] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.701513] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.701712] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.701727] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.701921] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.703402] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.703418] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.703681] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [268.703689] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [268.703698] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [268.703704] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [268.703713] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [268.703718] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [268.703723] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [268.703729] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [268.703734] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [268.703739] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [268.703938] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 2 to 0 or reprobing
<7> [268.703945] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.703953] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.704158] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.704413] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.704868] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.705061] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.705468] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.705662] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.705669] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.705861] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.707480] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.707489] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.707685] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.707880] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] status updated from connected to disconnected
<7> [268.707896] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.707997] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:65:VGA-1] EDID changed, epoch counter 62
<7> [268.708084] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.708092] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.708342] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.708610] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.708997] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.709188] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.709641] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.709837] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.709844] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.710035] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.711487] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.711495] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.711693] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.711888] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<6> [268.712734] [IGT] kms_force_connector_basic: finished subtest prune-stale-modes, SUCCESS
<7> [268.712972] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [268.713627] [drm:status_store] [CONNECTOR:61:LVDS-1] force updated from 0 to 0 or reprobing
<7> [268.713637] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [268.713650] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [268.713658] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [268.713737] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [268.713743] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [268.713787] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [268.713794] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [268.713801] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [268.713860] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [268.713865] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [268.714051] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:61:LVDS-1] EDID override reset
<7> [268.714097] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [268.714109] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [268.714118] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [268.714180] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [268.714185] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [268.714437] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [268.714445] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.714452] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.714689] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.714887] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.715267] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.715466] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.715846] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.716038] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.716046] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.716238] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.717816] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.717825] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.718019] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.718215] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.718326] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.718338] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.718547] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.718741] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.719125] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.719379] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.719770] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.719961] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.719968] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.720160] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.721625] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.721632] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.721827] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.722020] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.722170] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:65:VGA-1] EDID override reset
<7> [268.722200] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.722207] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.722444] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.722658] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.723041] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.723230] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.723687] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.723880] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.723886] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.724077] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.725544] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.725552] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.725744] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.725937] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.726142] [drm:status_store] [CONNECTOR:68:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [268.726150] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [268.726157] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [268.778505] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [268.795350] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.795361] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.795549] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [268.811344] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.811352] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [268.811540] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [268.811619] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [268.811627] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [268.864198] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [268.880387] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.880397] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.880584] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [268.896382] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.896390] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [268.896582] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [268.896770] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:68:HDMI-A-1] EDID override reset
<7> [268.896802] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [268.896809] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [268.947958] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [268.964418] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.964427] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.964611] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [268.980424] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.980432] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [268.980623] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [268.980834] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:76:DP-1] EDID override reset
<7> [268.980865] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1]
<7> [268.980872] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [268.981064] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected
<7> [268.981277] [drm:status_store] [CONNECTOR:81:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [268.981287] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [268.981298] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [268.981786] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.982069] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [268.982488] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.982806] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.982817] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.983137] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [268.985159] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.985174] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [268.985526] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [268.985628] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [268.985640] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [268.986171] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.986561] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [268.987251] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.987554] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.987562] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.987849] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [268.989659] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.989669] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [268.989959] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [268.990206] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:81:HDMI-A-2] EDID override reset
<7> [268.990252] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [268.990262] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [268.990808] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.991093] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [268.991554] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.991843] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.991852] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.992130] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [268.993957] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.993969] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [268.994274] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [268.994642] [drm:status_store] [CONNECTOR:85:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [268.994654] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [268.994666] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [268.995155] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [268.995548] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [268.996050] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [268.996332] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [268.996342] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.996676] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [268.998645] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [268.998657] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [268.998943] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [268.999038] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [268.999048] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [268.999506] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [268.999799] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [269.000281] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [269.000628] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [269.000638] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [269.000930] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [269.002702] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [269.002712] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [269.002997] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [269.003215] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:85:HDMI-A-3] EDID override reset
<7> [269.003260] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [269.003269] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [269.003832] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [269.004115] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [269.004635] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [269.004934] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [269.004944] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [269.005237] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [269.007089] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [269.007100] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [269.007423] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [269.007679] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:89:DP-2] EDID override reset
<7> [269.007725] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2]
<7> [269.007736] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [269.008051] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected
<7> [269.008282] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:93:DP-3] EDID override reset
<7> [269.008326] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3]
<7> [269.008336] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [269.008721] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected
<6> [269.010441] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [269.010756] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [269.010770] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [269.010784] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [269.011133] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [269.011496] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [269.012026] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [269.012323] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [269.012865] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [269.013169] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [269.013180] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [269.013591] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [269.015535] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [269.015548] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [269.015854] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [269.016155] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [269.016279] [drm:status_store] [CONNECTOR:61:LVDS-1] force updated from 0 to 0 or reprobing
<7> [269.016290] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [269.016305] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [269.016316] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [269.016499] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [269.016509] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [269.016617] [drm:status_store] [CONNECTOR:68:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [269.016626] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [269.016638] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [269.069254] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [269.085483] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [269.085494] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [269.085684] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [269.101634] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [269.101650] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [269.101882] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [269.101980] [drm:status_store] [CONNECTOR:81:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [269.101987] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [269.101995] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [269.102334] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [269.102645] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [269.103108] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [269.103317] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [269.103325] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [269.103581] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [269.105090] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [269.105098] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [269.105294] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [269.105373] [drm:status_store] [CONNECTOR:85:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [269.105380] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [269.105387] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [269.105802] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [269.106142] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [269.106746] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [269.106945] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [269.106952] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [269.107147] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [269.108691] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [269.108700] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [269.108898] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [269.109231] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [269.113787] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [269.113799] [drm:drm_client_modeset_probe]
<7> [269.113866] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [269.113879] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [269.113887] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [269.113964] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [269.113970] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [269.113978] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [269.113984] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [269.114203] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [269.114388] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [269.114804] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [269.115264] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [269.115888] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [269.116302] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [269.116318] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [269.116779] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [269.118700] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [269.118709] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [269.118906] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [269.119102] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [269.119110] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [269.119118] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [269.169675] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [269.185555] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [269.185577] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [269.185794] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [269.201560] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [269.201569] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [269.201765] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [269.201774] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1]
<7> [269.201781] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [269.201971] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected
<7> [269.201978] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [269.201984] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [269.202339] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [269.202598] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [269.203120] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [269.203404] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [269.203414] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [269.203743] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [269.205709] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [269.205721] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [269.206008] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [269.206019] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [269.206029] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [269.206529] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [269.206826] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [269.207321] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [269.207685] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [269.207696] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [269.207992] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [269.209914] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [269.209926] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [269.210213] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [269.210224] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2]
<7> [269.210235] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [269.210586] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected
<7> [269.210598] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3]
<7> [269.210609] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [269.210914] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected
<7> [269.210923] [drm:drm_client_modeset_probe] connector 61 enabled? yes
<7> [269.210931] [drm:drm_client_modeset_probe] connector 65 enabled? no
<7> [269.210938] [drm:drm_client_modeset_probe] connector 68 enabled? no
<7> [269.210944] [drm:drm_client_modeset_probe] connector 76 enabled? no
<7> [269.210951] [drm:drm_client_modeset_probe] connector 81 enabled? no
<7> [269.210957] [drm:drm_client_modeset_probe] connector 85 enabled? no
<7> [269.210964] [drm:drm_client_modeset_probe] connector 89 enabled? no
<7> [269.210970] [drm:drm_client_modeset_probe] connector 93 enabled? no
<7> [269.210999] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [269.211019] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61
<7> [269.211026] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0
<7> [269.211033] [drm:drm_client_modeset_probe] found mode 1366x768
<7> [269.211039] [drm:drm_client_modeset_probe] picking CRTCs for 1366x768 config
<7> [269.211074] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)
<6> [269.231030] Console: switching to colour frame buffer device 170x48
Created at 2024-01-22 00:38:54