Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 0.02 seconds
Igt-Version 
IGT-Version: 1.28-g5652fea13 (x86_64) (Linux: 6.7.0-linus-v6.7-g0dd3ee311255+ x86_64)
Out 
Using IGT_SRANDOM=1704659629 for randomisation
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.021s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.021s)
Dmesg
<6> [268.201953] Console: switching to colour dummy device 80x25
<6> [268.202731] [IGT] kms_force_connector_basic: executing
<7> [268.407568] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [268.408153] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [268.408516] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [268.409122] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [268.409132] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.409141] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.409394] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.409634] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.410035] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.410226] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.410641] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.410834] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.410842] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.411033] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.412577] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.412585] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.412777] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.412970] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.413022] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.413029] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.413231] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.413509] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.413940] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.414130] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.414570] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.414762] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.414768] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.414958] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.416420] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.416427] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.416618] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.416809] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.416919] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.416926] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.417126] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.417395] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.417827] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.418016] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.418401] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.418594] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.418600] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.418790] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.420205] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.420212] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.420447] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.420676] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<6> [268.421337] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [268.421615] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 2 or reprobing
<7> [268.421626] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.421634] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] status updated from disconnected to connected
<7> [268.421962] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.422209] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.422781] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.423079] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.423103] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.423427] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.425390] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.425415] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.425798] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [268.425808] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [268.425819] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [268.425828] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [268.425837] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [268.425846] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [268.425931] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.426151] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.426474] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.426962] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.427243] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.427265] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.427537] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.429022] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.429037] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.429331] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [268.429341] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [268.429352] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [268.429361] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [268.429370] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [268.429378] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [268.429663] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:65:VGA-1] EDID override set
<7> [268.429692] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.429736] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD monitor IGT
<7> [268.429743] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD size 24, SAD count 0
<7> [268.429879] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [268.429886] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [268.429895] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [268.429900] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [268.429909] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [268.429913] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [268.429918] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [268.429924] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [268.429929] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [268.429934] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [268.429939] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [268.430090] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:65:VGA-1] EDID override set
<7> [268.430121] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.430158] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD monitor IGT
<7> [268.430164] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD size 24, SAD count 0
<7> [268.430170] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:65:VGA-1] EDID changed, epoch counter 58
<7> [268.430378] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [268.430390] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [268.430405] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [268.430411] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [268.430421] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [268.430430] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [268.430438] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [268.430447] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [268.430634] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:65:VGA-1] EDID override reset
<7> [268.430666] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.430881] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.431088] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.431468] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.431667] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.431682] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.431874] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.433335] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.433348] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.433603] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [268.433611] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [268.433620] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [268.433626] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [268.433634] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [268.433639] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [268.433645] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [268.433650] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [268.433655] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [268.433660] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [268.433848] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 2 to 0 or reprobing
<7> [268.433855] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.433862] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.434070] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.434263] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.434740] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.434934] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.435305] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.435528] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.435535] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.435726] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.437235] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.437242] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.437460] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.437669] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] status updated from connected to disconnected
<7> [268.437683] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.437689] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:65:VGA-1] EDID changed, epoch counter 60
<7> [268.437769] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.437775] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.437978] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.438168] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.438724] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.438937] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.439422] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.439715] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.439725] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.440012] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.441908] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.441920] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.442212] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.442552] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<6> [268.443583] [IGT] kms_force_connector_basic: finished subtest prune-stale-modes, SUCCESS
<7> [268.443840] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [268.444559] [drm:status_store] [CONNECTOR:61:LVDS-1] force updated from 0 to 0 or reprobing
<7> [268.444570] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [268.444582] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [268.444591] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [268.444665] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [268.444670] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [268.444713] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [268.444720] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [268.444726] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [268.444781] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [268.444785] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [268.444913] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:61:LVDS-1] EDID override reset
<7> [268.444939] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [268.444945] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [268.444951] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [268.445003] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [268.445007] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [268.445171] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [268.445177] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.445184] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.445456] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.445716] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.446114] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.446333] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.446754] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.446948] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.446955] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.447156] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.448738] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.448746] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.448941] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.449135] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.449190] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.449197] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.449421] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.449626] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.450054] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.450243] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.450695] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.450901] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.450907] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.451098] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.452586] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.452593] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.452786] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.452978] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.453121] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:65:VGA-1] EDID override reset
<7> [268.453146] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.453152] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.453417] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.453662] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.454050] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.454238] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.454645] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.454837] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.454843] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.455032] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.456500] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.456507] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.456698] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.456891] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.457086] [drm:status_store] [CONNECTOR:68:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [268.457093] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [268.457100] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [268.510147] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [268.526333] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.526345] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.526533] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [268.542343] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.542351] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [268.542542] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [268.542618] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [268.542626] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [268.593024] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [268.609320] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.609330] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.609515] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [268.625335] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.625343] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [268.625536] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [268.625717] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:68:HDMI-A-1] EDID override reset
<7> [268.625747] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [268.625754] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [268.678211] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [268.694336] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.694347] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.694542] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [268.710339] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.710353] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [268.710577] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [268.710789] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:76:DP-1] EDID override reset
<7> [268.710819] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1]
<7> [268.710826] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [268.711043] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected
<7> [268.711223] [drm:status_store] [CONNECTOR:81:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [268.711230] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [268.711237] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [268.711726] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.711923] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [268.712329] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.712552] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.712559] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.712747] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [268.714263] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.714312] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [268.714509] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [268.714563] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [268.714570] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [268.714964] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.715153] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [268.715563] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.715761] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.715767] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.715954] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [268.717415] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.717422] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [268.717616] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [268.717765] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:81:HDMI-A-2] EDID override reset
<7> [268.717791] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [268.717798] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [268.718193] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.718438] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [268.718852] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.719042] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.719048] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.719235] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [268.720692] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.720699] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [268.720893] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [268.721092] [drm:status_store] [CONNECTOR:85:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [268.721099] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [268.721105] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [268.721614] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [268.721807] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [268.722183] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [268.722396] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [268.722403] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.722636] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [268.724140] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [268.724147] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [268.724404] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [268.724495] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [268.724502] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [268.724897] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [268.725087] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [268.725501] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [268.725693] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [268.725699] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.725885] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [268.727366] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [268.727374] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [268.727568] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [268.727710] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:85:HDMI-A-3] EDID override reset
<7> [268.727735] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [268.727742] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [268.728135] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [268.728349] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [268.728780] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [268.728970] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [268.728976] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.729162] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [268.730652] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [268.730659] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [268.730855] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [268.731010] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:89:DP-2] EDID override reset
<7> [268.731036] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2]
<7> [268.731042] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [268.731248] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected
<7> [268.731499] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:93:DP-3] EDID override reset
<7> [268.731526] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3]
<7> [268.731532] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [268.731739] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected
<6> [268.732844] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [268.733045] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [268.733055] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.733065] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.733346] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.733574] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.733970] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.734161] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.734609] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.734803] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.734811] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.735002] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.736545] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.736553] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.736745] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.736938] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.737019] [drm:status_store] [CONNECTOR:61:LVDS-1] force updated from 0 to 0 or reprobing
<7> [268.737026] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [268.737035] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [268.737042] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [268.737116] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [268.737121] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [268.737179] [drm:status_store] [CONNECTOR:68:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [268.737185] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [268.737191] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [268.789956] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [268.806334] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.806347] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.806557] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [268.822325] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.822334] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [268.822523] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [268.822619] [drm:status_store] [CONNECTOR:81:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [268.822626] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [268.822633] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [268.822996] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.823175] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [268.823629] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.823836] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.823843] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.824034] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [268.825547] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.825555] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [268.825749] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [268.825827] [drm:status_store] [CONNECTOR:85:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [268.825834] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [268.825840] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [268.826220] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [268.826547] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [268.827040] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [268.827357] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [268.827367] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.827654] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [268.829612] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [268.829624] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [268.829904] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [268.830425] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [268.839646] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [268.839675] [drm:drm_client_modeset_probe]
<7> [268.839845] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [268.839879] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [268.839902] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [268.840108] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [268.840124] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [268.840148] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [268.840167] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [268.841038] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [268.841400] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [268.842521] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.842824] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [268.843313] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [268.843517] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.843526] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.843718] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [268.845546] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [268.845559] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [268.845837] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [268.846115] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [268.846129] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [268.846140] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [268.896578] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [268.913335] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.913345] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.913529] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [268.929329] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [268.929337] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [268.929528] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [268.929537] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1]
<7> [268.929544] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [268.929741] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected
<7> [268.929747] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [268.929754] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [268.930109] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.930348] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [268.930848] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [268.931122] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.931132] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.931449] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [268.933447] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [268.933460] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [268.933671] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [268.933681] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [268.933688] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [268.934107] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [268.934429] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [268.934930] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [268.935205] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [268.935214] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [268.935568] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [268.937497] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [268.937509] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [268.937789] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [268.937800] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2]
<7> [268.937810] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [268.938107] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected
<7> [268.938117] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3]
<7> [268.938127] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [268.938500] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected
<7> [268.938511] [drm:drm_client_modeset_probe] connector 61 enabled? yes
<7> [268.938519] [drm:drm_client_modeset_probe] connector 65 enabled? no
<7> [268.938527] [drm:drm_client_modeset_probe] connector 68 enabled? no
<7> [268.938533] [drm:drm_client_modeset_probe] connector 76 enabled? no
<7> [268.938540] [drm:drm_client_modeset_probe] connector 81 enabled? no
<7> [268.938547] [drm:drm_client_modeset_probe] connector 85 enabled? no
<7> [268.938554] [drm:drm_client_modeset_probe] connector 89 enabled? no
<7> [268.938561] [drm:drm_client_modeset_probe] connector 93 enabled? no
<7> [268.938605] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [268.938625] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61
<7> [268.938633] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0
<7> [268.938640] [drm:drm_client_modeset_probe] found mode 1366x768
<7> [268.938647] [drm:drm_client_modeset_probe] picking CRTCs for 1366x768 config
<7> [268.938680] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)
<6> [268.973176] Console: switching to colour frame buffer device 170x48
Created at 2024-01-07 22:03:53