Result:
git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0
| Detail | Value |
|---|---|
| Duration | 4.18 seconds |
| Igt-Version |
IGT-Version: 1.28-g5652fea13 (x86_64) (Linux: 6.7.0-linus-v6.7-g0dd3ee311255+ x86_64) |
| Out |
Using IGT_SRANDOM=1704659745 for randomisation Starting subtest: basic-s2idle-without-i915 Opened device: /dev/dri/card0 [cmd] rtcwake: wakeup from "freeze" using /dev/rtc0 at Sun Jan 7 20:36:03 2024 Subtest basic-s2idle-without-i915: SUCCESS (4.179s) |
| Err |
Starting subtest: basic-s2idle-without-i915 Subtest basic-s2idle-without-i915: SUCCESS (4.179s) |
| Dmesg |
<6> [471.456756] [IGT] i915_suspend: executing
<6> [471.461332] [IGT] i915_suspend: starting subtest basic-s2idle-without-i915
<7> [471.674923] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K
<7> [471.675206] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [471.675412] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint LP PCH
<7> [471.675664] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [471.676067] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [471.676311] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz
<7> [471.677208] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [471.677373] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [471.677520] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M
<6> [471.677687] i915 0000:00:02.0: vgaarb: deactivate vga console
<7> [471.677942] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 7ff00047
<7> [471.678126] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K
<7> [471.678624] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x79ec6018
<7> [471.678865] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0
<7> [471.679055] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [471.679241] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [471.679446] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [471.687319] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483
<7> [471.687663] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [471.687885] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [471.688094] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [471.688302] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: LPDDR3
<7> [471.688471] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb DIMMs: no
<7> [471.688730] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [471.688964] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no
<7> [471.689194] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb DIMMs: no
<7> [471.689423] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [471.689677] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no
<7> [471.689911] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [471.690143] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [471.690308] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [471.691039] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [471.691396] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 203
<7> [471.691756] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [471.692095] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)
<7> [471.692429] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [471.692788] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [471.693124] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812)
<7> [471.693462] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)
<7> [471.693815] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [471.694152] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)
<7> [471.694494] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [471.694848] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)
<7> [471.695173] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0
<7> [471.695500] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [471.695844] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [471.696181] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [471.696508] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [471.696802] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [471.697123] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [471.697445] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [471.697785] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [471.698108] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 8
<7> [471.698431] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [471.698768] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8
<7> [471.699090] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02
<7> [471.699436] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [471.699879] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [471.700245] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO
<7> [471.700598] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [471.700893] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz
<7> [471.701212] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Max dotclock rate: 675000 kHz
<7> [471.701531] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [471.701993] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [471.702322] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [471.702668] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [471.703015] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [471.703441] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [471.703790] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [471.704121] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [471.704452] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [471.704863] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/skl_dmc_ver1_27.bin
<6> [471.706734] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/skl_dmc_ver1_27.bin (v1.27)
<7> [471.707488] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [471.708297] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV
<7> [471.708721] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us
<7> [471.709032] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [471.709340] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [471.709696] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [471.710000] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [471.710303] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [471.710636] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [471.710947] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [471.711256] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [471.714170] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.
<7> [471.716767] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [471.717157] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI A/PHY A] Using AUX CH A (VBT)
<7> [471.717506] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:94:DDI A/PHY A]
<7> [471.723588] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [471.723929] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [471.724244] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [471.724716] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [471.725064] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [471.725389] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [471.725739] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: HD eDP
<7> [471.726062] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [471.726384] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 10, level 255, controller 0
<7> [471.726718] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:0
<7> [471.727164] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:94:DDI A/PHY A] initial power sequencer: PPS 0
<7> [471.727543] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [471.727871] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [471.728164] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [471.728466] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [471.728813] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [471.729169] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [471.729844] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turning VDD on
<7> [471.730165] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [471.730542] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000
<7> [471.730932] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [471.731272] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008
<7> [471.731632] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [471.939734] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
<7> [471.940825] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000
<7> [471.943066] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 9f 40
<7> [471.946075] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1
<7> [471.964291] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [471.964346] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [471.964381] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [471.964995] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:95:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [471.966657] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:95:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [471.968383] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:95:eDP-1] DRRS type: static
<7> [471.970303] i915 0000:00:02.0: [drm:lpt_setup_backlight [i915]] [CONNECTOR:95:eDP-1] Using native PCH PWM for backlight control
<7> [471.971902] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:95:eDP-1] backlight initialized, disabled, brightness 0/937
<7> [471.974059] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [471.975524] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [471.976982] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [471.978450] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [471.980169] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [471.981638] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [471.983896] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:102:DDI B/PHY B] Using AUX CH B (VBT)
<7> [471.984850] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:102:DDI B/PHY B]
<7> [471.987251] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [471.988190] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:102:DDI B/PHY B]
<7> [471.988865] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:102:DDI B/PHY B] Using DDC pin 0x5 (VBT)
<7> [471.990098] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:117:DDI C/PHY C] Using AUX CH C (VBT)
<7> [471.990800] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:117:DDI C/PHY C]
<7> [471.992227] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [471.992904] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:117:DDI C/PHY C]
<7> [471.993498] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:117:DDI C/PHY C] Using DDC pin 0x4 (VBT)
<7> [471.995492] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled
<7> [471.996117] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled
<7> [471.996737] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled
<7> [471.997254] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [471.997783] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A
<7> [471.998293] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A
<7> [471.998825] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B
<7> [471.999328] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B
<7> [471.999868] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B
<7> [472.000383] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C
<7> [472.000905] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C
<7> [472.001411] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C
<7> [472.001960] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [472.002480] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:102:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [472.003007] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DP-MST A] hw state readout: disabled, pipe A
<7> [472.003485] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:105:DP-MST B] hw state readout: disabled, pipe B
<7> [472.003908] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:106:DP-MST C] hw state readout: disabled, pipe C
<7> [472.004322] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:117:DDI C/PHY C] hw state readout: disabled, pipe A
<7> [472.004736] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:119:DP-MST A] hw state readout: disabled, pipe A
<7> [472.005128] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:120:DP-MST B] hw state readout: disabled, pipe B
<7> [472.005522] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:121:DP-MST C] hw state readout: disabled, pipe C
<7> [472.005964] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1
<7> [472.006390] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [472.006836] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [472.007257] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [472.007812] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:eDP-1] hw state readout: disabled
<7> [472.008254] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:103:DP-1] hw state readout: disabled
<7> [472.008706] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:112:HDMI-A-1] hw state readout: disabled
<7> [472.009143] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:118:DP-2] hw state readout: disabled
<7> [472.009598] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:124:HDMI-A-2] hw state readout: disabled
<7> [472.010004] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [472.010398] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz
<7> [472.010814] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz
<7> [472.011202] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [472.011599] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz
<7> [472.011938] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz
<7> [472.012276] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz
<7> [472.012645] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [472.012996] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz
<7> [472.013338] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz
<7> [472.013708] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz
<7> [472.014049] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [472.014551] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]
<7> [472.014929] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]
<7> [472.015280] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]
<7> [472.015656] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling
<7> [472.016008] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [472.016344] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [472.016693] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [472.017117] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [472.017402] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [472.017759] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0
<7> [472.018106] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 5 GT workarounds on global
<7> [472.020598] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 8 engine workarounds on rcs'0
<7> [472.020940] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 5 whitelist workarounds on rcs'0
<7> [472.021252] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 12 context workarounds on rcs'0
<7> [472.041185] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed rcs'0 to rcs0
<7> [472.041398] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed bcs'0 to bcs0
<7> [472.041590] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed vcs'0 to vcs0
<7> [472.041834] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed vecs'0 to vecs0
<7> [472.042771] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV
<7> [472.043228] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping
<7> [472.043444] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping
<7> [472.043682] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping
<7> [472.043938] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [472.044254] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [472.052773] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:95:eDP-1] backlight device intel_backlight registered
<7> [472.053289] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1
<7> [472.054898] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:eDP-1] generating connector hotplug event
<7> [472.055922] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [472.057454] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:103:DP-1] generating connector hotplug event
<7> [472.058292] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:112:HDMI-A-1] generating connector hotplug event
<7> [472.059487] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DDI C/PHY C bus for card0-DP-2
<7> [472.061934] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:118:DP-2] generating connector hotplug event
<7> [472.062473] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:124:HDMI-A-2] generating connector hotplug event
<6> [472.062545] [drm] Initialized i915 1.6.0 20230929 for 0000:00:02.0 on minor 0
<7> [472.066636] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 5 outputs detected
<6> [472.094840] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [472.105334] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input72
<7> [472.106792] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)
<7> [472.108133] i915 display info: display version: 9
<7> [472.108140] i915 display info: cursor_needs_physical: no
<7> [472.108145] i915 display info: has_cdclk_crawl: no
<7> [472.108150] i915 display info: has_cdclk_squash: no
<7> [472.108154] i915 display info: has_ddi: yes
<7> [472.108159] i915 display info: has_dp_mst: yes
<7> [472.108163] i915 display info: has_dsb: no
<7> [472.108168] i915 display info: has_fpga_dbg: yes
<7> [472.108172] i915 display info: has_gmch: no
<7> [472.108176] i915 display info: has_hotplug: yes
<7> [472.108181] i915 display info: has_hti: no
<7> [472.108185] i915 display info: has_ipc: yes
<7> [472.108190] i915 display info: has_overlay: no
<7> [472.108194] i915 display info: has_psr: yes
<7> [472.108198] i915 display info: has_psr_hw_tracking: yes
<7> [472.108203] i915 display info: overlay_needs_physical: no
<7> [472.108207] i915 display info: supports_tv: no
<7> [472.108211] i915 display info: has_hdcp: yes
<7> [472.108216] i915 display info: has_dmc: yes
<7> [472.108220] i915 display info: has_dsc: no
<7> [472.108227] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D
<7> [472.108922] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C
<7> [472.109245] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B
<7> [472.109579] [drm:drm_client_modeset_probe]
<7> [472.109672] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [472.109688] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [472.109723] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E
<7> [472.110912] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [472.111251] i915 device info: pciid=0x1916 rev=0x07 platform=SKYLAKE (subplatform=0x1) gen=9
<7> [472.111259] i915 device info: graphics version: 9
<7> [472.111264] i915 device info: media version: 9
<7> [472.111268] i915 device info: graphics stepping: H0
<7> [472.111273] i915 device info: media stepping: H0
<7> [472.111277] i915 device info: display stepping: H0
<7> [472.111281] i915 device info: base die stepping: **
<7> [472.111285] i915 device info: gt: 2
<7> [472.111290] i915 device info: memory-regions: 0x21
<7> [472.111294] i915 device info: page-sizes: 0x11000
<7> [472.111298] i915 device info: platform: SKYLAKE
<7> [472.111303] i915 device info: ppgtt-size: 48
<7> [472.111307] i915 device info: ppgtt-type: 2
<7> [472.111312] i915 device info: dma_mask_size: 39
<7> [472.111316] i915 device info: is_mobile: no
<7> [472.111320] i915 device info: is_lp: no
<7> [472.111324] i915 device info: require_force_probe: no
<7> [472.111329] i915 device info: is_dgfx: no
<7> [472.111333] i915 device info: has_64bit_reloc: yes
<7> [472.111337] i915 device info: has_64k_pages: no
<7> [472.111341] i915 device info: gpu_reset_clobbers_display: no
<7> [472.111346] i915 device info: has_reset_engine: yes
<7> [472.111350] i915 device info: has_3d_pipeline: yes
<7> [472.111354] i915 device info: has_flat_ccs: no
<7> [472.111358] i915 device info: has_global_mocs: no
<7> [472.111363] i915 device info: has_gmd_id: no
<7> [472.111367] i915 device info: has_gt_uc: yes
<7> [472.111371] i915 device info: has_heci_pxp: no
<7> [472.111376] i915 device info: has_heci_gscfi: no
<7> [472.111380] i915 device info: has_guc_deprivilege: no
<7> [472.111385] i915 device info: has_guc_tlb_invalidation: no
<7> [472.111389] i915 device info: has_l3_ccs_read: no
<7> [472.111394] i915 device info: has_l3_dpf: no
<7> [472.111398] i915 device info: has_llc: yes
<7> [472.111403] i915 device info: has_logical_ring_contexts: yes
<7> [472.111407] i915 device info: has_logical_ring_elsq: no
<7> [472.111411] i915 device info: has_media_ratio_mode: no
<7> [472.111416] i915 device info: has_mslice_steering: no
<7> [472.111420] i915 device info: has_oa_bpc_reporting: no
<7> [472.111425] i915 device info: has_oa_slice_contrib_limits: no
<7> [472.111429] i915 device info: has_oam: no
<7> [472.111442] i915 device info: has_one_eu_per_fuse_bit: no
<7> [472.111446] i915 device info: has_pxp: no
<7> [472.111451] i915 device info: has_rc6: yes
<7> [472.111455] i915 device info: has_rc6p: no
<7> [472.111459] i915 device info: has_rps: yes
<7> [472.111464] i915 device info: has_runtime_pm: yes
<7> [472.111468] i915 device info: has_snoop: no
<7> [472.111472] i915 device info: has_coherent_ggtt: yes
<7> [472.111477] i915 device info: tuning_thread_rr_after_dep: no
<7> [472.111481] i915 device info: unfenced_needs_alignment: no
<7> [472.111486] i915 device info: hws_needs_physical: no
<7> [472.111490] i915 device info: has_pooled_eu: no
<7> [472.111495] i915 device info: rawclk rate: 24000 kHz
<7> [472.111500] i915 device info: iommu: disabled
<7> [472.111504] i915 device info: available engines: 40403
<7> [472.111509] i915 device info: slice total: 1, mask=0001
<7> [472.111514] i915 device info: subslice total: 3
<7> [472.111519] i915 device info: slice0: 3 subslices, mask=00000007
<7> [472.111524] i915 device info: slice1: 0 subslices, mask=00000000
<7> [472.111529] i915 device info: slice2: 0 subslices, mask=00000000
<7> [472.111534] i915 device info: EU total: 24
<7> [472.111538] i915 device info: EU per subslice: 8
<7> [472.111543] i915 device info: has slice power gating: no
<7> [472.111547] i915 device info: has subslice power gating: no
<7> [472.111552] i915 device info: has EU power gating: yes
<6> [472.111580] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [472.111585] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [472.111590] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [472.111632] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [472.111944] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [472.112242] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [472.112536] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [472.112862] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [472.112876] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [472.112886] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [472.112921] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [472.113222] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [472.120253] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [472.120623] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [472.121795] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] status updated from unknown to connected
<7> [472.122000] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [472.122010] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [472.122022] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [472.122034] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [472.122046] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [472.122626] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] status updated from unknown to disconnected
<7> [472.122649] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [472.122660] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [472.122671] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [472.123996] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [472.124341] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [472.125601] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [472.125944] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [472.125957] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [472.126251] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [472.132425] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [472.132441] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [472.132979] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] status updated from unknown to disconnected
<7> [472.133007] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [472.133031] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [472.133043] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [472.133386] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] status updated from unknown to disconnected
<7> [472.133410] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [472.133431] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [472.133442] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [472.134731] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [472.136976] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [472.137785] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [472.138120] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [472.138132] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [472.138428] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [472.142257] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [472.142271] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [472.142734] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] status updated from unknown to disconnected
<7> [472.142763] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [472.142845] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [472.142855] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [472.142862] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [472.142869] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [472.142876] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [472.142950] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [472.142969] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [472.142977] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [472.142984] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [472.142991] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [472.143013] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<7> [472.143055] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<7> [472.143162] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one
<7> [472.149000] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x000c0000
<6> [472.150853] fbcon: i915drmfb (fb0) is primary device
<6> [472.151724] Console: switching to colour frame buffer device 400x112
<6> [472.151746] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
<7> [472.157702] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [472.157716] [drm:drm_client_modeset_probe]
<7> [472.157799] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [472.157814] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [472.159467] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [472.160034] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [472.160295] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [472.160544] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [472.161063] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [472.161078] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [472.161088] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [472.161123] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [472.161376] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [472.165127] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [472.165410] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<6> [472.165923] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380
<7> [472.166498] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [472.166511] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [472.166523] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [472.166536] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [472.166548] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [472.167486] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [472.167499] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [472.167511] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [472.169361] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [472.169716] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [472.172393] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [472.172725] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [472.172738] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [472.172992] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [472.178626] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [472.178641] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [472.178927] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [472.178939] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [472.178951] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [472.179237] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [472.179248] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [472.179259] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [472.180029] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [472.180290] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [472.180802] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [472.181075] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [472.181086] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [472.181330] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [472.187752] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [472.187769] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [472.188056] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [472.188068] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [472.188077] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [472.188084] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [472.188091] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [472.188098] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [472.188160] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [472.188179] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [472.188186] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [472.188194] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [472.188200] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [472.188238] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<7> [472.189163] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:95:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [472.189499] i915 0000:00:02.0: [drm:intel_dp_compute_config_link_bpp_limits [i915]] [ENCODER:94:DDI A/PHY A][CRTC:51:pipe A] DP link limits: pixel clock 373250 kHz DSC off max lanes 4 max rate 540000 max pipe_bpp 24 max link_bpp 24.0000
<7> [472.189930] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24
<7> [472.190181] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1119750 available 2160000
<7> [472.191032] i915 0000:00:02.0: [drm:intel_dp_audio_compute_config [i915]] [CONNECTOR:95:eDP-1] SDP split enable: no
<7> [472.191356] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:51:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [472.191849] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:94:DDI A/PHY A] [CRTC:51:pipe A]
<7> [472.192109] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.enable (expected 0, found 1)
<7> [472.192388] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.active (expected 0, found 1)
<7> [472.192693] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4)
<7> [472.192972] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [472.193248] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4348677/8388608 link 362389/524288)
<7> [472.193794] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [472.194251] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [472.194761] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200)
<7> [472.195712] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3360)
<7> [472.196005] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200)
<7> [472.196282] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3360)
<7> [472.196722] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248)
<7> [472.196998] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280)
<7> [472.197279] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [472.198978] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [472.199431] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [472.200063] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1808)
<7> [472.200398] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1852)
<7> [472.201243] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [472.202023] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1852)
<7> [472.202314] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200)
<7> [472.202781] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3360)
<7> [472.203062] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200)
<7> [472.203337] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3360)
<7> [472.203803] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248)
<7> [472.204081] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280)
<7> [472.204356] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [472.206524] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [472.206848] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [472.207127] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1808)
<7> [472.207402] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1852)
<7> [472.207692] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1852)
<7> [472.207968] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [472.208244] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [472.208518] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [472.209001] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in enhanced_framing (expected no, found yes)
<7> [472.209291] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dpll_hw_state.ctrl1 (expected 0x00000000, found 0x00000001)
<7> [472.209684] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)
<7> [472.209964] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 373250)
<7> [472.210239] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 373250)
<7> [472.210513] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [472.210990] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [472.211328] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:51:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 892), active pipes 0x0 -> 0x1
<7> [472.211791] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 856), size 0 -> 856
<7> [472.212054] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:47:cursor A] ddb ( 0 - 0) -> ( 856 - 892), size 0 -> 36
<7> [472.212316] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm
<7> [472.212775] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0
<7> [472.213040] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 58, 84, 96, 184, 227, 245, 288, 0, 0, 0
<7> [472.213304] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 8, 59, 85, 97, 185, 228, 246, 289, 0, 0, 0
<7> [472.213768] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (373250 kHz) > [CRTC:51:pipe A] min cdclk (0 kHz)
<7> [472.214051] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (23329 kHz) > old min cdclk (0 kHz)
<7> [472.214334] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [472.214782] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 450000 kHz, actual 450000 kHz
<7> [472.215096] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1
<7> [472.215375] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:51:pipe A] allocated DPLL 0
<7> [472.215811] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:51:pipe A] reserving DPLL 0
<7> [472.216084] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: yes [modeset]
<7> [472.216360] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [472.216818] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0
<7> [472.217097] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [472.217375] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [472.217809] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
<7> [472.218086] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [472.218360] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4348677, data_n: 8388608, link_m: 362389, link_n: 524288, tu: 64
<7> [472.218832] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [472.219114] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: enabled
<7> [472.219387] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
<7> [472.219824] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [472.220103] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0
<7> [472.220111] i915 0000:00:02.0: pixelformat: RGB
<7> [472.220118] i915 0000:00:02.0: colorimetry: sRGB
<7> [472.220125] i915 0000:00:02.0: bpc: 0
<7> [472.220132] i915 0000:00:02.0: dynamic range: VESA range
<7> [472.220139] i915 0000:00:02.0: content type: Not defined
<7> [472.220146] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
<7> [472.220422] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [472.220921] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [472.221201] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
<7> [472.221484] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [472.221786] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
<7> [472.222063] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 373250
<7> [472.222339] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 73, ips linetime: 0
<7> [472.222635] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [472.222910] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [472.223183] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [472.223454] i915 0000:00:02.0: [drm:skl_dump_hw_state [i915]] dpll_hw_state: ctrl1: 0x1, cfgcr1: 0x0, cfgcr2: 0x0
<7> [472.223945] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x2 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [472.224219] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [472.224489] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [472.224929] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [472.225204] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [472.225474] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [472.225961] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [472.226233] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:96] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [472.226515] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [472.226959] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0
<7> [472.227233] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:39:plane 2A] fb: [NOFB], visible: no
<7> [472.227498] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:47:cursor A] fb: [NOFB], visible: no
<7> [472.228839] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 450000 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 1
<7> [472.229963] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:94:DDI A/PHY A]
<7> [472.230235] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:102:DDI B/PHY B]
<7> [472.230494] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:104:DP-MST A]
<7> [472.230941] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:105:DP-MST B]
<7> [472.231204] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:106:DP-MST C]
<7> [472.231459] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:117:DDI C/PHY C]
<7> [472.231900] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:119:DP-MST A]
<7> [472.232163] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:120:DP-MST B]
<7> [472.232420] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:121:DP-MST C]
<7> [472.232848] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [472.233286] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [472.233696] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2
<7> [472.233979] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3
<7> [472.234395] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:51:pipe A]
<7> [472.234811] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0
<7> [472.235379] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turn panel power on
<7> [472.235829] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [472.236145] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008
<7> [472.236395] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [472.236845] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power on
<7> [472.237144] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x0000000b
<7> [472.437928] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [472.439262] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [472.441717] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
<7> [472.449101] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
<7> [472.450403] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14
<7> [472.453151] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [472.454231] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
<7> [472.455316] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [472.459282] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Clock recovery OK
<7> [472.460635] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] >=5.4/6.48 Gbps link rate without sink TPS3 support
<7> [472.462037] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using DP training pattern TPS2
<7> [472.465848] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 2/2/2/2, pre-emphasis request: 1/1/1/1
<7> [472.466914] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 2(max)/2(max)/2(max)/2(max), pre-emphasis levels: 1/1/1/1
<7> [472.468065] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 08000000
<7> [472.472213] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 2/2/2/2, pre-emphasis request: 1/1/1/1
<7> [472.473317] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 2(max)/2(max)/2(max)/2(max), pre-emphasis levels: 1/1/1/1
<7> [472.474485] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 08000000
<7> [472.479329] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [472.480760] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [472.483141] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [472.485670] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [472.487176] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [472.489423] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:95:eDP-1] set backlight PWM = 937
<7> [472.491436] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23040000 bytes of contiguous stolen space for FBC, limit: 1
<7> [472.493097] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]
<7> [472.498451] i915 0000:00:02.0: [drm:intel_pipe_update_end [i915]] Atomic update on pipe (A) took 424 us, max time under evasion is 250 us
<7> [472.502302] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1
<7> [472.510766] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:95:eDP-1]
<7> [472.512450] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:51:pipe A]
<7> [472.514309] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp
<7> [472.515973] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [472.520212] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [472.520258] [drm:drm_client_modeset_probe]
<6> [472.520113] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [472.520702] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [472.520758] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [472.521850] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [472.527161] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [472.528331] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [472.529689] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [472.530985] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [472.532255] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [472.533767] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [472.533826] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [472.533873] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [472.534073] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [472.535357] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [472.538206] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [472.539430] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [472.542727] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [472.542778] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [472.542833] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [472.542888] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [472.542943] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [472.544342] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [472.544397] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [472.544449] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [472.546031] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [472.547242] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [472.548746] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [472.549993] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [472.550042] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [472.551232] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [472.558429] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [472.558467] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [472.559257] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [472.559291] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [472.559322] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [472.560184] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [472.560215] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [472.560246] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [472.561300] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [472.562030] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [472.563226] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [472.564036] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [472.564067] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [472.564823] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [472.569710] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [472.569739] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [472.570255] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [472.570277] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [472.570294] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [472.570309] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [472.570322] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [472.570335] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [472.570469] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [472.570506] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [472.570522] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [472.570537] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [472.570550] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [472.570658] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<7> [472.601397] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<6> [472.619442] [IGT] Unloading i915
<6> [472.619762] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC3246: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
<6> [472.619796] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<6> [472.619804] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
<6> [472.619811] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
<6> [472.619817] snd_hda_codec_realtek hdaudioC0D0: inputs:
<6> [472.619823] snd_hda_codec_realtek hdaudioC0D0: Headset Mic=0x19
<6> [472.619829] snd_hda_codec_realtek hdaudioC0D0: Headphone Mic=0x1a
<6> [472.619835] snd_hda_codec_realtek hdaudioC0D0: Internal Mic=0x12
<6> [472.621530] Console: switching to colour dummy device 80x25
<7> [472.682534] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [472.682820] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [472.683014] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [472.683203] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [472.683390] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [472.683734] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [472.684024] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [472.684294] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [472.684583] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<6> [472.694521] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input73
<6> [472.699446] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input74
<6> [472.700589] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input75
<6> [472.714775] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input76
<7> [472.817343] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [472.913743] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [472.914384] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [472.914783] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [472.915230] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [472.917127] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.enable (expected 1, found 0)
<7> [472.917681] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.active (expected 1, found 0)
<7> [472.918162] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in cpu_transcoder (expected 4, found -1)
<7> [472.919105] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [472.919963] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 4348677/8388608 link 362389/524288, found tu 0, data 0/0 link 0/0)
<7> [472.920877] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [472.921469] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [472.922102] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3200, found 0)
<7> [472.922719] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3360, found 0)
<7> [472.923294] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3200, found 0)
<7> [472.923937] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3360, found 0)
<7> [472.924522] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3248, found 0)
<7> [472.925167] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3280, found 0)
<7> [472.925785] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [472.926371] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [472.927004] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [472.927751] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1808, found 0)
<7> [472.928510] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1852, found 0)
<7> [472.929343] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1852, found 0)
<7> [472.930168] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3200, found 0)
<7> [472.931005] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3360, found 0)
<7> [472.931803] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3200, found 0)
<7> [472.932624] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3360, found 0)
<7> [472.933374] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3248, found 0)
<7> [472.934112] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3280, found 0)
<7> [472.934790] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [472.935395] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [472.936215] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [472.937021] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1808, found 0)
<7> [472.937832] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1852, found 0)
<7> [472.938640] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1852, found 0)
<7> [472.939399] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [472.940217] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [472.941011] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [472.941600] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in enhanced_framing (expected yes, found no)
<7> [472.942368] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0)
<7> [472.943173] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 373250, found 0)
<7> [472.943984] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 373250, found 0)
<7> [472.944785] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [472.945614] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [472.946366] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:51:pipe A] releasing DPLL 0
<7> [472.947178] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:51:pipe A] dbuf slices 0x1 -> 0x0, ddb (0 - 892) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [472.948117] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 856) -> ( 0 - 0), size 856 -> 0
<7> [472.948875] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:47:cursor A] ddb ( 856 - 892) -> ( 0 - 0), size 36 -> 0
<7> [472.949636] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [472.950347] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [472.951120] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 7, 58, 84, 96, 184, 227, 245, 288, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [472.951884] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 8, 59, 85, 97, 185, 228, 246, 289, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [472.952765] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [472.953372] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 337500 kHz, actual 337500 kHz
<7> [472.953978] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0
<7> [472.954689] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [modeset]
<7> [472.955230] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no
<7> [472.955820] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:39:plane 2A] fb: [NOFB], visible: no
<7> [472.956462] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:47:cursor A] fb: [NOFB], visible: no
<7> [472.957545] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR1
<7> [472.961746] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]
<7> [473.169055] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:95:eDP-1] set backlight PWM = 0
<7> [473.170702] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [473.191019] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x01000000, dig 0x11001010, pins 0x00000010, long 0x00000000
<7> [473.191144] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turn panel power off
<7> [473.192253] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [473.192195] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:94:DDI A/PHY A] - short
<7> [473.193394] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000000
<7> [473.242967] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [473.244559] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x01000000, dig 0x12001010, pins 0x00000010, long 0x00000010
<7> [473.245844] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:94:DDI A/PHY A] - long
<7> [473.246721] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:51:pipe A]
<7> [473.247338] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [473.249754] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring short hpd on eDP [ENCODER:94:DDI A/PHY A]
<7> [473.250950] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0
<7> [473.251281] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:94:DDI A/PHY A]
<7> [473.253399] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A]
<7> [473.255732] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [473.258342] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:94:DDI A/PHY A]
<7> [473.260016] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:102:DDI B/PHY B]
<7> [473.262007] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:104:DP-MST A]
<7> [473.263652] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:105:DP-MST B]
<7> [473.265196] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:106:DP-MST C]
<7> [473.266745] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:117:DDI C/PHY C]
<7> [473.268316] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:119:DP-MST A]
<7> [473.269873] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:120:DP-MST B]
<7> [473.271432] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:121:DP-MST C]
<7> [473.272881] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:95:eDP-1]
<7> [473.274536] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [473.276271] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [473.277933] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2
<7> [473.279636] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3
<7> [473.281483] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:51:pipe A]
<7> [473.350527] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]
<7> [473.438702] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper
<7> [473.439221] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [473.849218] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000
<7> [473.850418] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<6> [474.283844] PM: suspend entry (s2idle)
<6> [474.288778] Filesystems sync: 0.004 seconds
<6> [474.294188] Freezing user space processes
<6> [474.298648] Freezing user space processes completed (elapsed 0.004 seconds)
<6> [474.298716] OOM killer disabled.
<6> [474.298720] Freezing remaining freezable tasks
<6> [474.300686] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
<6> [474.320546] asix 1-1:1.0 enx00106031d5f9: Link is Down
<7> [474.343656] PM: suspend of devices complete after 28.998 msecs
<7> [474.343671] PM: start suspend of devices complete after 42.887 msecs
<7> [474.349388] PM: late suspend of devices complete after 5.709 msecs
<6> [474.376211] ACPI: EC: interrupt blocked
<7> [474.403095] PM: noirq suspend of devices complete after 33.459 msecs
<6> [474.404421] ACPI: \_SB_.PEPD: Successfully transitioned to state screen off
<6> [474.405828] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 entry
<7> [474.405837] PM: suspend-to-idle
<7> [489.548107] Timekeeping suspended for 14.767 seconds
<7> [489.550965] PM: Triggering wakeup from IRQ 9
<7> [489.551647] ACPI: PM: ACPI fixed event wakeup
<7> [489.551686] PM: resume from suspend-to-idle
<6> [489.554305] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 exit
<6> [489.555638] ACPI: \_SB_.PEPD: Successfully transitioned to state screen on
<6> [489.557006] ACPI: EC: interrupt unblocked
<7> [489.573576] PM: noirq resume of devices complete after 17.927 msecs
<7> [489.592920] PM: early resume of devices complete after 2.357 msecs
<6> [489.902469] asix 1-1:1.0 enx00106031d5f9: configuring for phy/internal link mode
<7> [489.911308] PM: resume of devices complete after 318.377 msecs
<6> [489.927691] OOM killer enabled.
<6> [489.927728] Restarting tasks ... done.
<5> [489.941469] random: crng reseeded on system resumption
<6> [489.959659] PM: suspend exit
<6> [489.969309] [IGT] Re-loading i915
<7> [490.204379] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K
<7> [490.204761] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [490.205000] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint LP PCH
<7> [490.205212] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [490.205542] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [490.205813] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz
<7> [490.206914] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [490.207101] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [490.207268] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M
<6> [490.207436] i915 0000:00:02.0: vgaarb: deactivate vga console
<7> [490.207797] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 7ff00047
<7> [490.208022] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K
<7> [490.208541] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x79ec6018
<7> [490.208819] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0
<7> [490.209023] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [490.209223] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [490.209421] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [490.217395] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483
<7> [490.217726] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [490.217955] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [490.218163] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [490.218372] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: LPDDR3
<7> [490.218551] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb DIMMs: no
<7> [490.218788] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [490.219028] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no
<7> [490.219267] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb DIMMs: no
<7> [490.219525] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [490.219760] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no
<7> [490.219998] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [490.220245] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [490.220524] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [490.221368] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [490.221718] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 203
<7> [490.222048] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [490.222368] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)
<7> [490.222639] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [490.222964] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [490.223286] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812)
<7> [490.223613] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)
<7> [490.223928] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [490.224245] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)
<7> [490.224579] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [490.224860] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)
<7> [490.225106] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0
<7> [490.225414] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [490.225731] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [490.226045] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [490.226354] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [490.226684] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [490.226986] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [490.227241] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [490.227454] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [490.227710] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 8
<7> [490.228007] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [490.228312] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8
<7> [490.228632] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02
<7> [490.228961] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [490.229369] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [490.229719] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO
<7> [490.229995] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [490.230267] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz
<7> [490.230590] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Max dotclock rate: 675000 kHz
<7> [490.230899] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [490.231327] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [490.231652] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [490.231944] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [490.232189] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [490.232561] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [490.232880] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [490.233193] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [490.233519] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [490.233883] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/skl_dmc_ver1_27.bin
<6> [490.235649] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/skl_dmc_ver1_27.bin (v1.27)
<7> [490.236456] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [490.237174] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV
<7> [490.237614] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us
<7> [490.237929] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [490.238232] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [490.238553] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [490.238854] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [490.239098] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [490.239330] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [490.239643] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [490.239949] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [490.242528] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.
<7> [490.244684] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [490.245062] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI A/PHY A] Using AUX CH A (VBT)
<7> [490.245328] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:94:DDI A/PHY A]
<7> [490.250555] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [490.250803] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [490.251028] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [490.251251] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [490.251563] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [490.251913] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [490.252143] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: HD eDP
<7> [490.252366] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [490.252625] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 10, level 255, controller 0
<7> [490.252932] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:0
<7> [490.253246] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:94:DDI A/PHY A] initial power sequencer: PPS 0
<7> [490.253554] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [490.254203] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [490.254415] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [490.254675] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [490.255063] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [490.255409] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [490.256110] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turning VDD on
<7> [490.256333] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [490.256723] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000
<7> [490.256987] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [490.257317] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008
<7> [490.257648] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [490.467239] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
<7> [490.469311] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000
<7> [490.470808] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 9f 40
<7> [490.473791] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1
<7> [490.499822] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [490.499878] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [490.499915] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [490.500331] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:95:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [490.502310] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:95:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [490.504111] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:95:eDP-1] DRRS type: static
<7> [490.507921] i915 0000:00:02.0: [drm:lpt_setup_backlight [i915]] [CONNECTOR:95:eDP-1] Using native PCH PWM for backlight control
<7> [490.509849] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:95:eDP-1] backlight initialized, disabled, brightness 0/937
<7> [490.513236] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [490.515130] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [490.516854] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [490.518597] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [490.520330] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [490.522127] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [490.526361] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:102:DDI B/PHY B] Using AUX CH B (VBT)
<7> [490.528383] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:102:DDI B/PHY B]
<7> [490.533592] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [490.535583] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:102:DDI B/PHY B]
<7> [490.537292] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:102:DDI B/PHY B] Using DDC pin 0x5 (VBT)
<7> [490.540882] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:117:DDI C/PHY C] Using AUX CH C (VBT)
<7> [490.542903] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:117:DDI C/PHY C]
<7> [490.546791] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [490.548716] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:117:DDI C/PHY C]
<7> [490.550436] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:117:DDI C/PHY C] Using DDC pin 0x4 (VBT)
<7> [490.555756] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled
<7> [490.557960] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled
<7> [490.560118] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled
<7> [490.562050] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [490.563988] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A
<7> [490.565902] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A
<7> [490.567764] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B
<7> [490.568828] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B
<7> [490.569899] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B
<7> [490.570944] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C
<7> [490.571998] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C
<7> [490.573070] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C
<7> [490.574153] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [490.575222] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:102:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [490.576267] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DP-MST A] hw state readout: disabled, pipe A
<7> [490.577196] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:105:DP-MST B] hw state readout: disabled, pipe B
<7> [490.577908] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:106:DP-MST C] hw state readout: disabled, pipe C
<7> [490.578657] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:117:DDI C/PHY C] hw state readout: disabled, pipe A
<7> [490.579323] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:119:DP-MST A] hw state readout: disabled, pipe A
<7> [490.580031] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:120:DP-MST B] hw state readout: disabled, pipe B
<7> [490.580847] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:121:DP-MST C] hw state readout: disabled, pipe C
<7> [490.581627] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1
<7> [490.582370] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [490.583151] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [490.583918] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [490.584865] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:eDP-1] hw state readout: disabled
<7> [490.585649] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:103:DP-1] hw state readout: disabled
<7> [490.586289] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:112:HDMI-A-1] hw state readout: disabled
<7> [490.586880] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:118:DP-2] hw state readout: disabled
<7> [490.587442] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:124:HDMI-A-2] hw state readout: disabled
<7> [490.588008] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [490.588554] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz
<7> [490.589072] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz
<7> [490.589625] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [490.590167] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz
<7> [490.590729] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz
<7> [490.591245] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz
<7> [490.591793] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [490.592339] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz
<7> [490.592892] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz
<7> [490.593421] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz
<7> [490.593958] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [490.594735] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]
<7> [490.595220] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]
<7> [490.595674] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]
<7> [490.596108] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling
<7> [490.596560] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [490.596974] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [490.597383] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [490.597936] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [490.598287] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [490.598699] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0
<7> [490.599131] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 5 GT workarounds on global
<7> [490.602332] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 8 engine workarounds on rcs'0
<7> [490.602808] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 5 whitelist workarounds on rcs'0
<7> [490.603232] i915 0000:00:02.0: [drm:wa_init_finish [i915]] GT0: Initialized 12 context workarounds on rcs'0
<7> [490.626969] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed rcs'0 to rcs0
<7> [490.627179] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed bcs'0 to bcs0
<7> [490.627328] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed vcs'0 to vcs0
<7> [490.627473] i915 0000:00:02.0: [drm:intel_engines_driver_register [i915]] renamed vecs'0 to vecs0
<7> [490.628162] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV
<7> [490.628686] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping
<7> [490.628943] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping
<7> [490.629134] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping
<7> [490.629320] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [490.629657] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [490.637450] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:95:eDP-1] backlight device intel_backlight registered
<7> [490.637976] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1
<7> [490.641315] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:eDP-1] generating connector hotplug event
<7> [490.642134] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [490.643595] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:103:DP-1] generating connector hotplug event
<7> [490.644122] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:112:HDMI-A-1] generating connector hotplug event
<7> [490.644776] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DDI C/PHY C bus for card0-DP-2
<7> [490.646160] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:118:DP-2] generating connector hotplug event
<7> [490.646974] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:124:HDMI-A-2] generating connector hotplug event
<6> [490.647083] [drm] Initialized i915 1.6.0 20230929 for 0000:00:02.0 on minor 0
<7> [490.650972] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 5 outputs detected
<6> [490.681596] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [490.692095] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input78
<7> [490.695094] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)
<7> [490.696343] i915 display info: display version: 9
<7> [490.696350] i915 display info: cursor_needs_physical: no
<7> [490.696355] i915 display info: has_cdclk_crawl: no
<7> [490.696359] i915 display info: has_cdclk_squash: no
<7> [490.696364] i915 display info: has_ddi: yes
<7> [490.696368] i915 display info: has_dp_mst: yes
<7> [490.696373] i915 display info: has_dsb: no
<7> [490.696377] i915 display info: has_fpga_dbg: yes
<7> [490.696382] i915 display info: has_gmch: no
<7> [490.696386] i915 display info: has_hotplug: yes
<7> [490.696390] i915 display info: has_hti: no
<7> [490.696395] i915 display info: has_ipc: yes
<7> [490.696399] i915 display info: has_overlay: no
<7> [490.696404] i915 display info: has_psr: yes
<7> [490.696408] i915 display info: has_psr_hw_tracking: yes
<7> [490.696412] i915 display info: overlay_needs_physical: no
<7> [490.696417] i915 display info: supports_tv: no
<7> [490.696421] i915 display info: has_hdcp: yes
<7> [490.696426] i915 display info: has_dmc: yes
<7> [490.696430] i915 display info: has_dsc: no
<7> [490.696438] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D
<7> [490.696850] [drm:drm_client_modeset_probe]
<7> [490.696944] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [490.696959] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [490.700561] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C
<7> [490.700911] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B
<7> [490.701233] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E
<7> [490.702464] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [490.704111] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [490.704437] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [490.704934] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [490.705234] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [490.707113] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [490.707127] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [490.707138] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [490.707178] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [490.707486] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [490.708943] i915 device info: pciid=0x1916 rev=0x07 platform=SKYLAKE (subplatform=0x1) gen=9
<7> [490.708951] i915 device info: graphics version: 9
<7> [490.708956] i915 device info: media version: 9
<7> [490.708961] i915 device info: graphics stepping: H0
<7> [490.708966] i915 device info: media stepping: H0
<7> [490.708970] i915 device info: display stepping: H0
<7> [490.708975] i915 device info: base die stepping: **
<7> [490.708979] i915 device info: gt: 2
<7> [490.708984] i915 device info: memory-regions: 0x21
<7> [490.708988] i915 device info: page-sizes: 0x11000
<7> [490.708993] i915 device info: platform: SKYLAKE
<7> [490.708997] i915 device info: ppgtt-size: 48
<7> [490.709002] i915 device info: ppgtt-type: 2
<7> [490.709007] i915 device info: dma_mask_size: 39
<7> [490.709011] i915 device info: is_mobile: no
<7> [490.709016] i915 device info: is_lp: no
<7> [490.709020] i915 device info: require_force_probe: no
<7> [490.709025] i915 device info: is_dgfx: no
<7> [490.709029] i915 device info: has_64bit_reloc: yes
<7> [490.709034] i915 device info: has_64k_pages: no
<7> [490.709038] i915 device info: gpu_reset_clobbers_display: no
<7> [490.709043] i915 device info: has_reset_engine: yes
<7> [490.709048] i915 device info: has_3d_pipeline: yes
<7> [490.709052] i915 device info: has_flat_ccs: no
<7> [490.709057] i915 device info: has_global_mocs: no
<7> [490.709061] i915 device info: has_gmd_id: no
<7> [490.709066] i915 device info: has_gt_uc: yes
<7> [490.709070] i915 device info: has_heci_pxp: no
<7> [490.709074] i915 device info: has_heci_gscfi: no
<7> [490.709079] i915 device info: has_guc_deprivilege: no
<7> [490.709083] i915 device info: has_guc_tlb_invalidation: no
<7> [490.709088] i915 device info: has_l3_ccs_read: no
<7> [490.709092] i915 device info: has_l3_dpf: no
<7> [490.709097] i915 device info: has_llc: yes
<7> [490.709101] i915 device info: has_logical_ring_contexts: yes
<7> [490.709106] i915 device info: has_logical_ring_elsq: no
<7> [490.709110] i915 device info: has_media_ratio_mode: no
<7> [490.709115] i915 device info: has_mslice_steering: no
<7> [490.709119] i915 device info: has_oa_bpc_reporting: no
<7> [490.709124] i915 device info: has_oa_slice_contrib_limits: no
<7> [490.709128] i915 device info: has_oam: no
<7> [490.709133] i915 device info: has_one_eu_per_fuse_bit: no
<7> [490.709137] i915 device info: has_pxp: no
<7> [490.709142] i915 device info: has_rc6: yes
<7> [490.709146] i915 device info: has_rc6p: no
<7> [490.709150] i915 device info: has_rps: yes
<7> [490.709155] i915 device info: has_runtime_pm: yes
<7> [490.709159] i915 device info: has_snoop: no
<7> [490.709164] i915 device info: has_coherent_ggtt: yes
<7> [490.709168] i915 device info: tuning_thread_rr_after_dep: no
<7> [490.709173] i915 device info: unfenced_needs_alignment: no
<7> [490.709177] i915 device info: hws_needs_physical: no
<7> [490.709182] i915 device info: has_pooled_eu: no
<7> [490.709186] i915 device info: rawclk rate: 24000 kHz
<7> [490.709191] i915 device info: iommu: disabled
<7> [490.709196] i915 device info: available engines: 40403
<7> [490.709201] i915 device info: slice total: 1, mask=0001
<7> [490.709206] i915 device info: subslice total: 3
<7> [490.709210] i915 device info: slice0: 3 subslices, mask=00000007
<7> [490.709216] i915 device info: slice1: 0 subslices, mask=00000000
<7> [490.709221] i915 device info: slice2: 0 subslices, mask=00000000
<7> [490.709226] i915 device info: EU total: 24
<7> [490.709230] i915 device info: EU per subslice: 8
<7> [490.709235] i915 device info: has slice power gating: no
<7> [490.709239] i915 device info: has subslice power gating: no
<7> [490.709244] i915 device info: has EU power gating: yes
<6> [490.709249] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [490.709254] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [490.709259] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [490.710698] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [490.711019] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [490.711878] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] status updated from unknown to connected
<7> [490.712087] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [490.712097] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [490.712109] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [490.712121] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [490.712134] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [490.712689] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] status updated from unknown to disconnected
<7> [490.712711] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [490.712722] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [490.712733] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [490.714106] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [490.714438] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [490.718558] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [490.718902] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [490.718915] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [490.719212] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [490.723052] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [490.723065] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [490.723383] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] status updated from unknown to disconnected
<7> [490.723409] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [490.723433] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [490.723444] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [490.723970] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] status updated from unknown to disconnected
<7> [490.723996] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [490.724018] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [490.724029] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [490.724786] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [490.725091] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [490.726353] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [490.726761] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [490.726773] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [490.728690] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [490.732532] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [490.732546] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [490.732870] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] status updated from unknown to disconnected
<7> [490.732898] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [490.732908] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [490.732917] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [490.732924] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [490.732931] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [490.732938] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [490.733011] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [490.733031] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [490.733039] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [490.733046] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [490.733052] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [490.733076] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<7> [490.733119] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<7> [490.733229] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one
<7> [490.741641] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x000c0000
<6> [490.744034] fbcon: i915drmfb (fb0) is primary device
<6> [490.744988] Console: switching to colour frame buffer device 400x112
<6> [490.745012] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
<7> [490.753720] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [490.753733] [drm:drm_client_modeset_probe]
<7> [490.753813] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [490.753828] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [490.756143] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [490.756425] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [490.756953] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [490.757206] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [490.757665] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [490.757680] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [490.757690] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [490.757729] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [490.757979] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [490.759237] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [490.760072] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [490.760369] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<6> [490.764905] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380
<7> [490.765913] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [490.765926] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [490.765939] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [490.765951] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [490.765964] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [490.766973] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [490.766989] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [490.767001] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [490.768187] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [490.768460] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [490.769151] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [490.769427] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [490.769439] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [490.769869] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [490.773475] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [490.773490] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [490.774215] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [490.774230] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [490.774242] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [490.774772] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [490.774786] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [490.774797] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [490.775779] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [490.776041] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [490.776681] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [490.776950] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [490.776963] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [490.777207] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [490.780880] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [490.780894] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [490.781156] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [490.781169] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [490.781177] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [490.781185] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [490.781191] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [490.781198] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [490.781269] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [490.781287] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [490.781295] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [490.781302] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [490.781308] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [490.781346] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<6> [490.781440] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [490.781953] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:95:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [490.782260] i915 0000:00:02.0: [drm:intel_dp_compute_config_link_bpp_limits [i915]] [ENCODER:94:DDI A/PHY A][CRTC:51:pipe A] DP link limits: pixel clock 373250 kHz DSC off max lanes 4 max rate 540000 max pipe_bpp 24 max link_bpp 24.0000
<7> [490.782715] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24
<7> [490.782966] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1119750 available 2160000
<7> [490.783225] i915 0000:00:02.0: [drm:intel_dp_audio_compute_config [i915]] [CONNECTOR:95:eDP-1] SDP split enable: no
<6> [490.783546] [IGT] i915_suspend: finished subtest basic-s2idle-without-i915, SUCCESS
<7> [490.783469] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:51:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [490.783690] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [490.783952] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:94:DDI A/PHY A] [CRTC:51:pipe A]
<7> [490.784206] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.enable (expected 0, found 1)
<7> [490.784473] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.active (expected 0, found 1)
<7> [490.784704] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [490.784927] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4)
<7> [490.785198] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [490.785331] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [490.785468] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4348677/8388608 link 362389/524288)
<7> [490.785967] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [490.786252] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [490.786715] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200)
<7> [490.786996] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3360)
<7> [490.787269] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200)
<7> [490.787726] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3360)
<7> [490.788002] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248)
<7> [490.788272] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280)
<7> [490.788715] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [490.788987] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [490.789256] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [490.789688] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1808)
<7> [490.789959] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1852)
<7> [490.790229] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1852)
<7> [490.790553] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200)
<7> [490.790829] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3360)
<7> [490.791100] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200)
<7> [490.791369] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3360)
<7> [490.791837] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248)
<7> [490.792111] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280)
<7> [490.792382] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [490.792882] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [490.793156] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [490.793426] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1808)
<7> [490.793872] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1852)
<7> [490.794143] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1852)
<7> [490.794413] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [490.794862] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [490.795136] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [490.795411] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in enhanced_framing (expected no, found yes)
<7> [490.795881] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dpll_hw_state.ctrl1 (expected 0x00000000, found 0x00000001)
<7> [490.796156] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)
<7> [490.796429] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 373250)
<7> [490.796939] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 373250)
<7> [490.797214] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [490.797485] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [490.797992] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:51:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 892), active pipes 0x0 -> 0x1
<7> [490.798297] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 856), size 0 -> 856
<7> [490.798720] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:47:cursor A] ddb ( 0 - 0) -> ( 856 - 892), size 0 -> 36
<7> [490.798977] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm
<7> [490.799233] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0
<7> [490.799699] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 58, 84, 96, 184, 227, 245, 288, 0, 0, 0
<7> [490.799954] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 8, 59, 85, 97, 185, 228, 246, 289, 0, 0, 0
<7> [490.800254] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (373250 kHz) > [CRTC:51:pipe A] min cdclk (0 kHz)
<7> [490.800739] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (23329 kHz) > old min cdclk (0 kHz)
<7> [490.801018] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [490.801286] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 450000 kHz, actual 450000 kHz
<7> [490.801735] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1
<7> [490.802010] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:51:pipe A] allocated DPLL 0
<7> [490.802276] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:51:pipe A] reserving DPLL 0
<7> [490.802727] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: yes [modeset]
<7> [490.803043] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [490.803313] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0
<7> [490.803755] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [490.804030] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [490.804297] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
<7> [490.804821] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [490.805102] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4348677, data_n: 8388608, link_m: 362389, link_n: 524288, tu: 64
<7> [490.805372] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [490.805820] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: enabled
<7> [490.806114] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
<7> [490.806401] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [490.806916] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0
<7> [490.806924] i915 0000:00:02.0: pixelformat: RGB
<7> [490.806931] i915 0000:00:02.0: colorimetry: sRGB
<7> [490.806938] i915 0000:00:02.0: bpc: 0
<7> [490.806944] i915 0000:00:02.0: dynamic range: VESA range
<7> [490.806965] i915 0000:00:02.0: content type: Not defined
<7> [490.806973] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
<7> [490.807264] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [490.807848] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [490.808151] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
<7> [490.808421] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [490.808813] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
<7> [490.809102] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 373250
<7> [490.809385] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 73, ips linetime: 0
<7> [490.809918] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [490.810206] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [490.810489] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [490.810930] i915 0000:00:02.0: [drm:skl_dump_hw_state [i915]] dpll_hw_state: ctrl1: 0x1, cfgcr1: 0x0, cfgcr2: 0x0
<7> [490.811215] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x2 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [490.811652] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [490.811993] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [490.812263] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [490.812786] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [490.813080] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [490.813373] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [490.813695] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:96] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [490.813982] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [490.814260] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0
<7> [490.814711] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:39:plane 2A] fb: [NOFB], visible: no
<7> [490.815087] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:47:cursor A] fb: [NOFB], visible: no
<7> [490.816431] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 450000 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 1
<7> [490.817763] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:94:DDI A/PHY A]
<7> [490.818057] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:102:DDI B/PHY B]
<7> [490.818335] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:104:DP-MST A]
<7> [490.818690] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:105:DP-MST B]
<7> [490.818951] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:106:DP-MST C]
<7> [490.819208] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:117:DDI C/PHY C]
<7> [490.819466] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:119:DP-MST A]
<7> [490.820007] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:120:DP-MST B]
<7> [490.820285] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:121:DP-MST C]
<7> [490.820751] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [490.821244] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [490.821761] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2
<7> [490.822071] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3
<7> [490.822764] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:51:pipe A]
<7> [490.823078] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0
<7> [490.823902] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turn panel power on
<7> [490.824283] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [490.824774] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008
<7> [490.825043] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [490.825324] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power on
<7> [490.825964] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x0000000b
<6> [490.865715] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC3246: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
<6> [490.865745] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<6> [490.865752] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
<6> [490.865759] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
<6> [490.865764] snd_hda_codec_realtek hdaudioC0D0: inputs:
<6> [490.865770] snd_hda_codec_realtek hdaudioC0D0: Headset Mic=0x19
<6> [490.865776] snd_hda_codec_realtek hdaudioC0D0: Headphone Mic=0x1a
<6> [490.865782] snd_hda_codec_realtek hdaudioC0D0: Internal Mic=0x12
<7> [490.937002] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [490.937238] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [490.937417] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [490.937632] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [490.937891] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [490.938146] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [490.938401] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [490.938673] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [490.938929] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<6> [490.948761] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input79
<6> [490.950162] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input80
<6> [490.957220] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input81
<6> [490.959774] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input82
<7> [491.026541] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [491.026854] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [491.027414] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
<7> [491.032176] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
<7> [491.033243] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14
<7> [491.034183] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [491.034458] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
<7> [491.034756] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [491.036167] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Clock recovery OK
<7> [491.036425] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] >=5.4/6.48 Gbps link rate without sink TPS3 support
<7> [491.036765] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using DP training pattern TPS2
<7> [491.038773] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 2/2/2/2, pre-emphasis request: 1/1/1/1
<7> [491.039045] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 2(max)/2(max)/2(max)/2(max), pre-emphasis levels: 1/1/1/1
<7> [491.039300] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 08000000
<7> [491.041548] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [491.041808] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [491.042533] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [491.043192] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [491.043446] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [491.043895] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:95:eDP-1] set backlight PWM = 937
<7> [491.044296] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23040000 bytes of contiguous stolen space for FBC, limit: 1
<7> [491.044611] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]
<7> [491.059974] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1
<7> [491.061951] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:95:eDP-1]
<7> [491.062240] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:51:pipe A]
<7> [491.062643] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp
<7> [491.062911] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [491.064035] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [491.064434] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<6> [491.065993] [IGT] i915_suspend: exiting, ret=0
<7> [491.066351] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [491.076725] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [491.076735] [drm:drm_client_modeset_probe]
<7> [491.076804] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [491.076815] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [491.078183] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [491.078479] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [491.078766] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [491.079027] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [491.079368] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [491.079382] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [491.079393] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [491.079447] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [491.079726] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [491.080691] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [491.080969] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [491.082109] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [491.082120] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [491.082132] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [491.082144] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [491.082156] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [491.082559] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [491.082571] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [491.082582] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [491.083557] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [491.083836] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [491.084329] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [491.084634] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [491.084646] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [491.084858] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [491.088017] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [491.088026] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [491.088249] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [491.088258] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [491.088266] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [491.088457] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [491.088465] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [491.088471] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [491.088929] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [491.089115] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [491.089472] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [491.089706] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [491.089716] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [491.089889] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [491.093419] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [491.093429] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [491.093640] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [491.093650] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [491.093659] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [491.093666] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [491.093675] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [491.093682] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [491.093745] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [491.093761] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [491.093766] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [491.093770] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [491.093775] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [491.093800] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
|