Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 0.10 seconds
Igt-Version 
IGT-Version: 1.28-g619c3f3ff (x86_64) (Linux: 6.7.0-rc8-linus-v6.7-rc8-g610a9b8f49fb+ x86_64)
Out 
Using IGT_SRANDOM=1704057498 for randomisation
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.096s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.096s)
Dmesg
<6> [219.337063] Console: switching to colour dummy device 80x25
<6> [219.338015] [IGT] kms_force_connector_basic: executing
<7> [219.356954] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [219.360717] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [219.362633] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [219.366309] [drm:status_store] [CONNECTOR:45:VGA-1] force updated from 0 to 0 or reprobing
<7> [219.366355] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.366393] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:45:VGA-1] force=1
<7> [219.380203] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [219.381634] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.382976] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [219.384953] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.386200] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.386250] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [219.387857] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [219.389688] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.389729] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [219.391344] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.391383] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.391414] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.391442] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [219.391553] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [219.391598] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [219.391933] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.391989] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:45:VGA-1] force=1
<7> [219.394965] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [219.396310] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.397370] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [219.398848] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.399927] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.399971] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [219.401279] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [219.403160] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.403254] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [219.405035] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.405086] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.405129] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.405169] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [219.405209] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [219.405249] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [219.405455] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.405600] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:45:VGA-1] force=1
<7> [219.413589] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [219.414864] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.417301] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [219.419066] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.420746] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.420799] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [219.423666] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [219.425815] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.425859] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [219.427583] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.427633] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.427677] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.427749] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [219.427790] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [219.427828] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<6> [219.428296] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [219.429975] [drm:status_store] [CONNECTOR:45:VGA-1] force updated from 0 to 2 or reprobing
<7> [219.430031] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.430369] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.431920] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [219.433439] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.434687] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.434792] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [219.436132] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [219.438043] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.438154] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [219.440143] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.440188] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.440236] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.440280] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [219.440325] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [219.440370] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [219.440798] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.441268] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.442616] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [219.444160] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.445564] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.445657] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [219.446923] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [219.448990] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.449344] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [219.451614] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.451664] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.451706] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.451746] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [219.451784] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [219.451823] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [219.454037] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:45:VGA-1] EDID override set
<7> [219.454259] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.454856] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:45:VGA-1] ELD monitor IGT
<7> [219.454908] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:45:VGA-1] ELD size 24, SAD count 0
<7> [219.454950] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:45:VGA-1] EDID changed, epoch counter 3
<7> [219.456250] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [219.456304] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [219.456366] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [219.456410] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [219.456555] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.456591] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [219.456634] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [219.456674] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [219.456713] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.456753] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.456793] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [219.458454] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:45:VGA-1] EDID override set
<7> [219.458867] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.459191] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:45:VGA-1] ELD monitor IGT
<7> [219.459236] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:45:VGA-1] ELD size 24, SAD count 0
<7> [219.459276] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:45:VGA-1] EDID changed, epoch counter 4
<7> [219.461458] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [219.461579] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [219.461649] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.461683] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [219.461724] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [219.461764] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.461802] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.461841] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [219.463124] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:45:VGA-1] EDID override reset
<7> [219.463417] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.464044] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.465450] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [219.467045] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.468806] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.468900] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [219.470660] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [219.472757] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.472854] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [219.474966] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [219.475026] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [219.475093] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [219.475347] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [219.475414] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.475447] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.475561] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.475603] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [219.475643] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [219.475684] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [219.477700] [drm:status_store] [CONNECTOR:45:VGA-1] force updated from 2 to 0 or reprobing
<7> [219.477753] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.477804] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:45:VGA-1] force=1
<7> [219.495264] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [219.496602] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.498136] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [219.499598] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.500673] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.500712] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [219.501778] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [219.503593] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.503653] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [219.505643] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.505693] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.505740] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.505785] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [219.505830] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [219.505874] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [219.506238] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.506576] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:45:VGA-1] force=1
<7> [219.512814] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [219.514562] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.515602] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [219.516885] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.518188] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.518230] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [219.519559] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [219.522210] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.522266] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [219.524164] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.524214] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.524257] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.524297] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [219.524336] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [219.524376] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<6> [219.525177] [IGT] kms_force_connector_basic: finished subtest prune-stale-modes, SUCCESS
<7> [219.526432] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [219.530142] [drm:status_store] [CONNECTOR:45:VGA-1] force updated from 0 to 0 or reprobing
<7> [219.530192] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.530228] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:45:VGA-1] force=1
<7> [219.546186] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [219.547573] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.548861] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [219.550306] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.551617] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.551666] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [219.552972] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [219.555026] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.555086] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [219.557054] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.557108] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.557154] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.557199] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [219.557243] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [219.557287] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [219.557757] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.557816] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:45:VGA-1] force=1
<7> [219.562414] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [219.564003] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.565297] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [219.566881] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.568220] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.568267] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [219.569610] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [219.571639] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.571696] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [219.573608] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.573655] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.573696] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.573735] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [219.573775] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [219.573814] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [219.574979] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:45:VGA-1] EDID override reset
<7> [219.575206] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.575253] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:45:VGA-1] force=1
<7> [219.578618] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [219.580249] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.581622] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [219.583186] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.584650] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.584697] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [219.585997] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [219.588011] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.588068] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [219.589990] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.590027] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.590056] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.590081] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [219.590106] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [219.590141] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<6> [219.594247] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [219.595562] [drm:status_store] [CONNECTOR:45:VGA-1] force updated from 0 to 0 or reprobing
<7> [219.595621] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1]
<7> [219.595675] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:45:VGA-1] force=1
<7> [219.612549] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [219.614027] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.615342] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [219.616966] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [219.618282] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.618330] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [219.619598] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [219.621651] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [219.621712] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [219.623689] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:45:VGA-1] probed modes :
<7> [219.623740] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [219.623787] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [219.623830] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [219.623873] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [219.623917] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [219.626562] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<6> [219.662302] Console: switching to colour frame buffer device 128x48
Created at 2023-12-31 22:48:27