Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 0.02 seconds
Igt-Version 
IGT-Version: 1.28-g2a2b71616 (x86_64) (Linux: 6.7.0-rc6-linus-v6.7-rc6-gceb6a6f023fd+ x86_64)
Out 
Using IGT_SRANDOM=1702856411 for randomisation
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.021s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.021s)
Dmesg
<6> [128.621590] Console: switching to colour dummy device 80x25
<6> [128.622005] [IGT] kms_force_connector_basic: executing
<7> [128.669852] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [128.670567] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [128.670954] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [128.671911] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 0 or reprobing
<7> [128.671929] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.671943] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [128.672277] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [128.672590] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [128.673132] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.673440] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [128.673955] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.674266] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.674278] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.674591] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [128.675640] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.675652] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [128.676148] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.676162] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.676174] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.676185] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [128.676195] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [128.676205] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [128.676275] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.676287] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [128.676636] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [128.677029] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [128.677559] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.677879] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [128.678380] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.678663] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.678671] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.678994] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [128.680004] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.680014] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [128.680395] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.680403] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.680413] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.680421] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [128.680429] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [128.680437] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [128.680528] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.680538] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [128.680866] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [128.681164] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [128.681677] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.682037] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [128.682536] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.682854] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.682862] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.683159] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [128.684169] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.684179] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [128.684561] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.684569] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.684578] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.684586] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [128.684594] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [128.684603] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<6> [128.685059] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [128.685376] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 2 or reprobing
<7> [128.685386] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.685646] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.685976] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [128.686484] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.686802] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.686823] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.687120] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [128.688314] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.688336] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [128.688643] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.688650] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.688656] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.688662] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [128.688667] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [128.688673] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [128.688765] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.689013] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.689301] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [128.689798] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.690092] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.690109] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.690395] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [128.691408] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.691427] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [128.691833] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.691842] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.691851] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.691860] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [128.691868] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [128.691877] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [128.692264] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:61:VGA-1] EDID override set
<7> [128.692310] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.692378] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD monitor IGT
<7> [128.692388] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD size 24, SAD count 0
<7> [128.692613] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [128.692624] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [128.692638] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [128.692648] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [128.692661] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.692668] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [128.692676] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [128.692685] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [128.692693] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.692701] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.692709] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [128.693015] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:61:VGA-1] EDID override set
<7> [128.693071] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.693134] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD monitor IGT
<7> [128.693143] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD size 24, SAD count 0
<7> [128.693151] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:61:VGA-1] EDID changed, epoch counter 6
<7> [128.693371] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [128.693382] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [128.693396] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.693402] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [128.693411] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [128.693420] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.693428] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.693436] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [128.693657] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:61:VGA-1] EDID override reset
<7> [128.693708] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.694024] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.694309] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [128.694798] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.695091] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.695108] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.695394] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [128.696449] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.696468] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [128.696880] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [128.696892] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [128.696906] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [128.696916] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [128.696929] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.696937] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.696945] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.696957] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [128.696965] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [128.696973] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [128.697258] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 2 to 0 or reprobing
<7> [128.697268] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.697279] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [128.697580] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [128.698003] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [128.698545] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.698872] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [128.699375] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.699664] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.699673] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.700001] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [128.701027] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.701039] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [128.701434] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.701443] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.701453] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.701462] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [128.701472] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [128.701481] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [128.701546] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.701557] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [128.701885] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [128.702182] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [128.702696] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.703016] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [128.703513] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.703817] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.703825] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.704120] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [128.705154] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.705165] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [128.705546] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.705555] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.705563] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.705572] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [128.705580] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [128.705588] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<6> [128.706064] [IGT] kms_force_connector_basic: finished subtest prune-stale-modes, SUCCESS
<7> [128.706356] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [128.707189] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 0 or reprobing
<7> [128.707200] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.707212] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [128.707515] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [128.707828] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [128.708329] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.708569] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [128.708956] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.709208] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.709219] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.709416] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [128.710326] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.710334] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [128.710599] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.710606] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.710613] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.710618] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [128.710624] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [128.710630] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [128.710681] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.710688] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [128.710917] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [128.711143] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [128.711531] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.711737] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [128.712128] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.712317] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.712322] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.712512] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [128.713407] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.713414] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [128.713668] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.713674] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.713679] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.713684] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [128.713689] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [128.713694] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [128.713889] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:61:VGA-1] EDID override reset
<7> [128.713920] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.713926] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [128.714126] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [128.714316] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [128.714702] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.714919] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [128.715311] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.715499] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.715505] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.715695] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [128.716607] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.716614] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [128.716933] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.716940] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.716945] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.716950] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [128.716955] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [128.716960] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [128.717155] [drm:status_store] [CONNECTOR:64:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [128.717163] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:64:HDMI-A-1]
<7> [128.717170] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [128.717563] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [128.717787] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [128.718183] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [128.718389] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [128.718398] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.718587] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [128.719529] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [128.719537] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [128.719754] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [128.719815] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:64:HDMI-A-1]
<7> [128.719826] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [128.720218] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [128.720405] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [128.720746] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [128.720955] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [128.720961] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.721145] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [128.722044] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [128.722051] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [128.722240] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [128.722375] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:64:HDMI-A-1] EDID override reset
<7> [128.722403] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:64:HDMI-A-1]
<7> [128.722409] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [128.722804] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [128.722992] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [128.723360] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [128.723548] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [128.723554] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.723755] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [128.724678] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [128.724684] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [128.724907] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [128.725090] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:72:DP-1] EDID override reset
<7> [128.725122] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:72:DP-1]
<7> [128.725129] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:72:DP-1]
<7> [128.725375] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:72:DP-1] disconnected
<6> [128.726127] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [128.726307] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 0 or reprobing
<7> [128.726316] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1]
<7> [128.726323] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [128.726543] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [128.726794] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [128.727218] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.727460] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [128.727916] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [128.728109] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.728115] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.728306] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [128.729207] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [128.729215] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [128.729480] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:VGA-1] probed modes :
<7> [128.729486] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [128.729493] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [128.729498] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [128.729504] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [128.729509] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [128.729577] [drm:status_store] [CONNECTOR:64:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [128.729583] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:64:HDMI-A-1]
<7> [128.729590] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [128.730026] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [128.730216] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [128.730588] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [128.730806] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [128.730812] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [128.731038] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [128.731939] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [128.731947] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [128.732138] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [128.732448] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<6> [128.763174] Console: switching to colour frame buffer device 128x48
Created at 2023-12-18 01:03:21