Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Duration 0.27 seconds
Igt-Version 
IGT-Version: 1.28-g0e1019715 (x86_64) (Linux: 6.7.0-rc5-linus-v6.7-rc5-ga39b6ac3781d+ x86_64)
Out 
Using IGT_SRANDOM=1702248034 for randomisation
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1ec/0x740
   drm_ioctl_kernel+0xbf/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x7c/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915]
   __intel_runtime_pm_put+0x179/0x2c0 [i915]
   intel_dmc_debugfs_status_show+0x349/0x450 [i915]
   seq_read_iter+0x114/0x450
   seq_read+0xab/0xe0
   full_proxy_read+0x5b/0x80
   vfs_read+0xac/0x2e0
Wakeref count: 1
Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   __intel_display_power_put_async+0x3d/0x160 [i915]
   intel_atomic_commit_tail+0xa49/0xd50 [i915]
   intel_atomic_commit+0x381/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1ec/0x740
   drm_ioctl_kernel+0xbf/0x150
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.270s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.270s)
Dmesg
<6> [74.824546] Console: switching to colour dummy device 80x25
<6> [74.824595] [IGT] kms_pm_rpm: executing
<7> [74.832194] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [74.836067] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [74.836074] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [74.836232] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [74.836680] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [74.836685] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [74.837771] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [74.838698] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [74.839453] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [74.839887] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [74.839892] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [74.840283] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.840399] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [74.840819] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.840968] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.840972] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [74.841084] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [74.845341] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.845346] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [74.845471] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [74.845831] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [74.845836] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [74.845976] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [74.845991] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [74.845994] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [74.847076] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [74.848196] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [74.848957] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [74.848975] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [74.848978] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [74.849390] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.849557] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [74.849949] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.850095] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.850099] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [74.850210] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [74.854489] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.854493] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [74.854620] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [74.854645] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [74.854649] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [74.854787] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [74.854839] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [74.854842] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [74.855926] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [74.856969] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [74.857709] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [74.857757] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [74.857761] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [74.858174] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.858292] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [74.858627] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.858798] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.858802] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [74.858914] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [74.863043] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.863047] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [74.863162] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [75.052655] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [75.053193] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.053708] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.054290] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.055204] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [85.244633] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [85.251335] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [85.921630] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [85.931000] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [85.932474] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [85.932926] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [85.933737] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [85.934551] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [85.935768] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [85.935658] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [85.935970] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [85.936155] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [85.937478] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [85.938427] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [85.938938] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [85.939745] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [85.939895] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [85.940313] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [85.940508] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [85.940514] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [85.940638] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [85.944986] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [85.944991] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [85.945229] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [86.060596] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [86.060782] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [86.060924] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [86.061061] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [86.061706] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [86.062330] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [86.065461] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [86.146706] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [86.158499] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [86.170840] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [86.179848] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [86.180946] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [86.181357] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [86.182086] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [86.182968] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [86.183291] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [86.183676] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [86.183879] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [86.184030] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [86.185530] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [86.186268] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [86.186795] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [86.187318] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [86.187541] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [86.188021] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [86.188259] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [86.188266] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [86.188481] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [86.192670] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [86.192674] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [86.308634] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [86.308973] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [86.309254] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [86.309564] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [86.310389] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [86.310713] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [86.317146] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [86.405952] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [86.413556] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [86.414314] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [86.414686] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [86.415399] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [86.417232] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [86.417537] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [86.417933] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [86.418287] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [86.419610] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [86.420488] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [86.421164] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [86.421647] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [86.421764] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [86.422172] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [86.422334] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [86.422339] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [86.422466] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [86.426649] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [86.426657] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<6> [86.427241] [IGT] kms_pm_rpm: exiting, ret=0
<6> [86.428203] Console: switching to colour frame buffer device 128x48
Created at 2023-12-10 23:55:45